Transition Networks E-TBT-HB-1004 Manual de usuario

Model 1004

(E-TBT-HB-1004)

7366.C

For assistance in installing, using, or

maintaining the TRANSITION Networks

Model 1004 Ethernet™ Repeater Hub,

contact TRANSITION Networks

Technical Support at:

(800) 260-1312

or contact your local distributor.

Model 1004

12-Port Ethernet Hub

MODEL 1004 12-PORT HUB

SPECIFICATIONS

Standards

IEEE 802.2, 802.3

Physical

Dimensions

17.0" X 7.5" X 1.7" (432 mm x 191 mm x 43 mm

Input Power

Universal Power Supply

Input Range: 85 to 265 VAC at 47 to 63 Hz.

(Rated at 40 watts maximum.)

AC Input:

TN PN Requirement Location

3344 120 volts, 60 hertz USA/Canada/Mexico

3344 100 volts, 50-60 hertz Japan

3347 230 volts, 50 hertz Europe

3348 240 volts, 50 hertz Australia

3349 240 volts, 50 hertz United Kingdom

Environment

Temperature: 0-50°C (32° to 122° F )

Humidity 10-90%, non condensing

Altitude 0-10,000 feet

Warranty

5 years

Model 1004 12-Port Ethernet™ Repeater Hub 20

CAUTION: RJ connectors are NOT INTENDED FOR

CONNECTION TO THE PUBLIC TELEPHONE

NETWORK. Failure to observe this caution could result

in damage to the public telephone network.

Compliance Information

UL Listed

C-UL Listed (Canada)

CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class

A digital device, pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user

will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for

digital apparatus set out on the radio interference regulations of the Canadian

Department of Communications.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

form or by any means – graphic, electronic, or mechanical – without written

permission from TRANSITION Networks Inc.

Trademark Notice

All registered trademarks and trademarks are the property of their respective

owners.

Der Anschluss dieses Gerätes an ein öffentlickes

Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst gegen die

jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie

91/263/EWG zur Angleichung der Rechtsvorschriften der

Mitgliedstaaten über Telekommunikationsendeinrichtungen

einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

10Base2 Cable Specifications

The physical characteristics of the 10Base2 cable must meet or exceed IEEE 802.3

10Base2 specifications.

Cable Characteristics:

Cable type: Stranded Coaxial RG58 (ThinNet)

Impedance: 50 Ω@ 10 MHz

Mutual Capacitance: 24 pF/ft ±20% @ 10 MHz

Maximum Cable Length:185 meters (610 feet)

Maximum number network connections:30

Minimum distance between connections: 0.5 meters (1.6 feet)

Terminate 10Base2 cable at one end using a 50 ohm terminator and at the

other end using a 50 ohm terminator grounded to earth ground.

10BaseT Cable and Connector Specifications

The physical characteristics of the 10BaseT cable must meet or exceed IEEE 802.3

10BaseT specifications.

10BaseT Cable Characteristics:

Category 3 wire or better is required; category 5 wire is recommended. Either

shielded twisted pair (STP) or unshielded twisted pair (UTP) can be used. DO

NOT USE FLAT OR SILVER SATIN WIRE.

Category 3:

Gauge 24 to 22 AWG

Attenuation 28 dB/1000’ @ 10 MHz

Differential Characteristic Impedance 100 Ω±10% @ 10 MHz

Category 5:

Gauge 24 to 22 AWG

Attenuation 20 dB/1000’ @ 10 MHz

Differential Characteristic Impedance 100 Ω±10% @ 10 MHz

Maximum Cable Length: 100 meters (330 feet)

10BaseT Connector Characteristics:

The two active pairs in a 10BaseT network are pins 1 & 2 and pins 3 & 6. Use

only dedicated wire pairs (such as blue/white & white/blue, orange/white &

white/orange) for the active pins. 10BaseT cable for unlike devices (such as

hub to terminal device) must be configured as straight through; 10BaseT cable

for like devices (such as hub to hub or terminal device to terminal device) must

be configured as crossover.

Twisted

Pair #1

Twisted

Pair #2

Crossover Cable

Connectors for like devices

Twisted

Pair #1

Twisted

Pair #2

Straight Through Cable

Connectors for unlike devices

Model 1004 12-Port Ethernet™ Repeater Hub

Table of Contents

1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1

The Model 1004 Repeater Hub . . . . . . . . . . . . . . . . . . . . . . .1

Model 1004 Repeater Hub Features . . . . . . . . . . . . . . . . . . . . .1

Networking the Model 1004 Repeater Hub . . . . . . . . . . . . . . . .2

Model 1004 Repeater Hub Connectors, Indicators,

and Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2 SITE CONSIDERATIONS. . . . . . . . . . . . . . . . . . . . 4

Ensuring Correct Segment Number . . . . . . . . . . . . . . . . . . . .5

Ensuring Correct 10BaseT Configuration . . . . . . . . . . . . . . . .8

3 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpacking the Model 1004 Repeater Hub . . . . . . . . . . . . . .7

Installing Slide-In Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Installing Model 1004 Repeater Hub . . . . . . . . . . . . . . . . . . .9

Connecting Cable to SIC and RJ-45 Connectos . . . . . . . . . .r10

BNC Connector/10Base2 Connection . . . . . . . . . . . . . . . . . . .10

Twisted Pair Connector/10BaseT Connection . . . . . . . . . . . . .11

Female AUConnector/10Base5 or Transceiver Connection . . .12

Male AUIConnector/PC Connection . . . . . . . . . . . . . . . . . . . .13

Fiber OpticConnector/10BaseFL Connection . . . . . . . . . . . . . .13

Connecting Power to Model 1004 Repeater . . . . . . . . . . . .14

4 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Monitoring Power LED . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Monitoring Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

5 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . 16

Fault Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Technical Support Contact . . . . . . . . . . . . . . . . . . . . . . . . .16

WARRANTY STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

ETHERNET CABLE SPECIFICATIONS. . . . . . . . . . . . . . . . . . 19

MODEL 1004 12-PORT HUB SPECIFICATIONS . . . . . . . . 21

ETHERNET CABLE SPECIFICATIONS

AUI Cable and Connector Specifications

The cable is a special 4-pair individually shielded with an overall braided

shield.

Maximum AUI Cable Length: 50 meters (165 feet)

AUI Connector Characteristics:

AUI Port: Male DB-15 with locking posts.

AUI Connection: Cable shell must be grounded.

Connector Legend: 1 Logic Ref. 6 Power Return 11 Logic Ref

2 Collision+ 7 N/C 12 Receive

3 Transmit+ 8 Logic Ref. 13 Power

4 Logic Ref. 9 Collision-- 14 Logic Ref.

5 Receive+ 10Transmit- 15 N/C

10BaseFL Cable and Connector Specifications

The physical characteristics of the 10BaseFL cable must meet or exceed IEEE

802.3 10BaseFL specifications.

10BaseFL Cable Characteristics:

Fiber Optic Cable Recommended: 62.5/125 µm multimode fiber

Optional: 100/140 µm multimode fiber

85/125 µm multimode fiber

50/125 µm multimode fiber

Fiber Optic Transmitter Power: Average power: -15.0 dBm

Peak power:-12.0 dBm ±1dBm

Fiber Optic Receiver Sensitivity: Average sensitivity: -27.4 dBm

Bit error rate: ≤10-10

Maximum Cable Length: 2000 meters (6500 feet)

10BaseFL Connector Characteristics:

ST type connectors (SMA type available upon request)

10Base5 Cable and Connector Specifications

The physical characteristics of the 10Base5 cable must meet or exceed IEEE 802.3

10Base5 specifications.

10Base5 Cable Characteristics:

Cable type: RG8 Solid Coaxial (ThickNet)

Impedance: 50 Ω@ 10 MHz

Capacitance: 26pF/ft

Maximum Cable Length: 500 meters (1650 feet)

Maximum number network connections: 100

Minimum distance between connections: 2.5 meters (8.2 feet)

Terminate 10Base5 cable at one end using a 50 ohm terminator and at the

other end using a 50 ohm terminator grounded to earth ground.

Maximum number of terminal devices on Ethernet network: 1024

Model 1004 12-Port Ethernet™ Repeater Hub 18

1. INTRODUCTION

This guide is intended for the system or network administrator

responsible for installing and monitoring a TRANSITION Networks

Model 1004 12-Port Ethernet™ Repeater Hub. A working knowledge of

local area network (LAN) operations, including familiarity with

communications protocols used on interconnected LANs, is assumed.

The Model 1004 Repeater Hub

The TRANSITION Networks Model 1004 12-Port Ethernet™ Repeater

Hub, is a small, multi-purpose Ethernet repeater that is site-

configurable, using an optional Slide In Card (SIC), for various signal

transmission media.

• Twelve fixed RJ-45 twisted-pair connectors

• SICs, if installed, provide fiber optic, male and female AUI,

BNC, or RJ-45 connectors.

• SICs allow future network expansion or modification

12 Port Ethernet 10BaseT Hub w/ SIC Slot

™

LAN Master T12

networks

TRANSITION

L/P

12 3 4 5 67 8 9101112

Power

MDI MDI-X L/P

L/P

Port 1

The sole purpose of this remedy shall be provided the customer with the replacement or

repair of non-conforming goods in the manner described in this Warranty statement. This

exclusive remedy shall not be deemed to have failed of its essential purpose so long as TN is

willing and able to repair or replace the defective item(s) or refund the purchase price.

TN reserves the right to inspect products claimed to be defective under warranty either at the

customer’s location or at TN’s plant. TN assumes no liability for liability charges incidental

to the adjustment, service, repairing, removal or replacement of the product, or other costs,

or the expense of repairs made outside of its factory, except when made with TN’s prior

written consent. Additionally, Transition Networks reserves the right to charge for all testing

and shipping incurred, if after testing, a return is classified as “No Problem Found”.

TN’s total liability in connection with the products and their installation to all persons and

from all causes in the aggregate, whether in contract, tort, or strict liability, shall not exceed

the amount paid to TN for the product directly related to the alleged damage. However, in

no event shall TN have any liability to a customer or any third party for products

manufactures according to the customer’s specifications.

C. Return Procedure

The customer must follow this procedure for the return of defective items:

1. Locate the serial number(s) of the item(s) to be returned.

2. Determine the date the item(s) was received.

3. Contact Transition Networks Technical Support to determine if the problem can be

corrected on site.

If not, and the product is covered by warranty, then:

• Call the distributor directly or contact TN.

• Request a Return Material Authorization (RMA).

• Ship the item, prepaid in original packaging to Transition Networks at the above

address.

• Include the RMA number on the outside of the carton and/or on the Packing List.

• Include a copy of the RMA form.

• Include a copy of the original invoice or packing list (if possible) to expedite

processing.

• The item(s) may be shipped by the customer or the distributor.

• Transition Networks will repair or replace the unit, at TN’s discretion, and cover the

cost of the return freight to the distributor or to the customer, whichever requested

the RMA number.

If the item(s) was received more than five years ago, or if the item(s) is no longer covered by

warranty for other reasons, then:

• Call the distributor or contact TN.

• Request a Material Repair Authorization number (MRA).

• Ship the item(s), prepaid, in the original packaging to Transition Networks at the

above address.

• Include the MRA number on the outside of the carton add/or on the Packing List.

• Include a copy of the MRA form.

• Include a copy of the original invoice or packing list (if possible) to expedite processing.

• Only the customer (end-user) may send the items(s) to TN.

• TN will contact the customer after the item(s) have been received, inspected, and a

cost estimate of the repair determined.

• The repair charges may be billed, with customer’s approval, though the distributor, or

on a prepaid or C.O.D. basis directly to the customer. The charges will include the

cost of shipping.

The return authorization numbers are valid only for 90 days from the date issued.

Model 1004 12-Port Ethernet™ Repeater Hub 2

Networking the Model 1004 Repeater Hub

The Model 1004 Repeater Hub can be installed in an Ethernet network

by connecting 10BaseT cable between RJ-45 connectors on the front of

the hubs.

Additionally, the SIC slot on the back of the hub can be used to

connect various media, selectable from among 10Base2, 10BaseT,

10BaseFL, and 10Base5.

SIC Connection

networksTRANSITION

12 3 4 5 6 7 8 9 10 11 12

networksTRANSITION

12 3 45 678 9 10 1112

10BaseT (100 meters)

10Base2 (185 meters)

10Base5 (500 meters)

10BaseFL (2000 meters)

networksTRANSITION

12 3 4 5 6 7 8 9 10 11 12

networksTRANSITION

12 3 4 5 6 7 8 9 10 11 12

Warranty Statement

A. Five Year Warranty

Transition Networks, Inc. (TN) warrants, for a period of five years, that TN products (with

the exception of power supplies and fans that TN warrants for two years) will be free from

defects in materials and workmanship, and will be in conformity with TN’s specifications.

TN’s warranty on products manufactured by or assembled for TN in accordance with a

customer’s specifications, is a five-year warranty that the goods conform to such

specifications.

The warranty is invalidated if the goods have been subject to alterations, misuse, accident,

Acts of God (e.g., damage by floods, lightning strikes, Etc.), tampering, improper

maintenance, improper installation, or abuse. If the user is unsure about the proper means

of installing or using the equipment, contact TN’s free Technical Support or Network

Design Services, which can be reached by:

Telephone 1.800.LAN.WANS or 612.941.7600

Fax 612.941.2322

E-mail [email protected]

Internet http://www.transition.com

THE ABOVE WARRANTY IS EXCLUSIVE AND EXTENDS ONLY TO PRODUCTS

ASSEMBLED BY TRANSITION NETWORKS, INC. TO THE EXTENT PERMITTED BY LAW,

TN DOES NOT MAKE AND DISCLAIMS ALL OTHER WARRANTIES, EXCEPT TITLE,

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF

DESCRIPTION, MERCHANTIBILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-

INFRINGEMENT, AND ANY WARRANTY BASED UPON PRIOR WRITTEN OR ORAL

REPRESENTATIONS REGARDING SUCH PRODUCTS MADE BY TN, ITS EMPLOYEES,

AGENTS, OR REPRESENTATIVES.

B. Limitations and Exclusions

If the customer believes any goods sold by TN are defective and within the warranty period,

the following general procedure will be followed:

1. Locate the serial number and delivery date of the item(s).

2. Notify TN within the warranty period.

3. TN will promptly issue a return authorization form for the goods.

4. Upon receiving the form, the customer will promptly return the item(s) at customers

own expense, shipped prepaid, to the distributor from which it was purchased, or

directly to TN.

TN will only accept goods for return if the following conditions have been met:

1. A return form is obtained from TN.

2. The freight charges have been prepaid by the customer.

3. Goods are re-packed in their original packaging.

If under warranty TN shall, at its option, (1) repair the goods free of charge (2) replace the

goods free of charge, or (3) accept the return of the item(s) and credit the current price to

the reseller (within 90 days of purchase), or (4) if the goods are not under warranty, will

repair the item(s) at a minimum charge of USD $200 (two hundred U.S. dollars) per item.

THIS IS THE EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. IN NO EVENT

SHALL TRANSITION NETWORKS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FOR BREACH OF ANY

CONDITION OF SALE, FOR NEGLIGENCE, ON THE BASIS OF STRICT LIABILITY,

CONTRACT, OR OTHERWISE AND IRRESPECTIVE OF WHETHER TN IS INFORMED BY

CUSTOMER OF THE POSSIBILITY OF SUCH DAMAGES IN ADVANCE OF THIS SALE.

Model 1004 12-Port Ethernet™ Repeater Hub 16

1004 Repeater Connectors, Indicators and

Switch

Connectors

Twelve (12) RJ-45 10BaseT connectors are located on the front of

the Model 1004 Repeater Hub.

One (1) power connector is located on the back of the Model 1004

Repeater Hub.

NOTE: Slide-In cards (SICs), if installed, provide additional fiber

optic, male and female AUI, BNC, or RJ-45 connectors.

LEDs

The Power LED indicates the Model 1004 Repeater Hub connection

to AC power.

One set of Partition, Link and Receive LEDs indicate (for each port)

the status of the Model 1004 Repeater Hub 10BaseT connections.

MDI Switch

The MDI switch reverses the straight-through/crossover cable

polarity of the RJ-45 10BaseT connector #1.

5. MAINTENANCE

WARNING: DO NOT, UNDER ANY CIRCUMSTANCES,

open and attempt to repair the Model 1004 Repeater Hub.

Failure to observe this warning could result in personal

injury or death from electrical shock.

NOTE: Failure to observe the above warning will immediately void

the warranty.

Fault Isolation

If two network devices fail to communicate through the 1004

Repeater, consider the following:

•Are the LEDs described in the previous section functioning

properly?

•Do network devices have Link Integrity enabled?

•Do network devices communicate when the 1004

Repeater is not installed between them?

•Is flat or “silver satin”wire used in site internal wiring?

•Are internal wiring patch cords, punch down blocks, and

wall jacks properly pinned or configured?

•Is the thinnet cable unbroken and properly connected?

•Are network interface cards properly configured?

Technical Support Contact

For assistance in fault isolation and in maintaining the Model 1004

Repeater, contact:

Technical Support (800) 260-1312

or your local distributor.

L/P

Power

12 Port Ethernet 10BaseT Hub w/ SIC Slot

™

LAN Master T12

networks

TRANSITION

L/P

1 2 3 4 5 6 7 8 9 10 11 12

Power

MDI MDI-X L/P

L/P

Port 1

RJ-45 Connector and Indicators

Port 1

MDI Switch

Power Indicator

Model 1004 12-Port Ethernet™Repeater Hub 4

4. OPERATION

The Model 1004 Repeater Hub requires no intervention beyond

occasionally monitoring the Power and Status LEDs.

Monitoring Power LED

The green Power LED is illuminated when the Model 1004 Repeater

Hub is connected to power.

Monitoring Status LEDs

The green Link LED blinks, indicating a partition condition, when the

Model 1004 Repeater Hub port registers sixty-four consecutive

collisions.

The green Link LED is illuminated a good port link has been achieved.

The green Receive LED is illuminated continuously when the Model

1004 Repeater Hub port registers packets received.

2. SITE CONSIDERATIONS

The site for the Model 1004 Repeater Hub must provide:

•AC power outlet for each Model 1004 Repeater Hub

•Adequate ventilation

•Standard environmental conditions

•Isolation from electrical noise, including radio transmitters and

broadband amplifiers, motors, high power electrical lines, or

fluorescent light fixtures.

Additionally:

•The twisted pair cables should not run in the same conduit with

power line cables.

•Phone lines should be separated from data cables.

•Flat or “silver satin”wires should not be used.

•RJ-45 connected cables should be configured as crossover or

straight through according to installation requirements.

And:

•Since the Model 1004 Repeater Hub is an Ethernet repeater, the

entire installation should comply with the IEEE Ethernet 802.3

specification

•RJ-45 connected cables should be configured as crossover or

straight through according to installation requirements.

Model 1004 12-Port Ethernet™Repeater Hub 14

Connecting Power to Model 1004 Repeater

To power ON the Model 1004 Repeater:

1. At Model 1004 Repeater back, locate the Unit power

receptacle and associated fuse.

2. Verify that fuse is installed at correct setting for power source

voltage.

NOTE: The installed fuse rating is indicated by the reading at

lower right corner of fuse holder.

If not installed at correct setting for power source voltage:

•Carefully open fuse receptacle, using a small flat

blade screwdriver.

•Rotate fuse holder 180°to the correct rating

orientation.

•Install fuse holder in correct rating orientation.

•Close fuse receptacle.

3. Plug unit end (female) of power cord into Model 1004

Repeater power receptacle.

4. Plug outlet end (male) of power cord into correct voltage AC

wall socket.

5. At Model 1004 Repeater front, verify that POWER LED is

illuminated.

NOTE: After the power supply adapter is connected to the Model

1004 Repeater and to external power, the green Power LED is

illuminated.

Ensuring Correct Segment Number

Ethernet 802.3 specifications define segment number, as well as cable

characteristics. (A segment is the cable connection between cable

interfaces in an Ethernet LAN.)

When connecting 1004 Repeaters, the transmission path between any

two Data Terminating Equipment (DTE) terminals can consist of no

more than five segments.

To assign segment numbers to cable connections:

1. Determine the two terminals in the network which are

separated by the greatest number of segments.

2. Assign a segment path between the terminals by labeling the

cable connected to one of the terminals “segment 1”and the

segment connected to the other terminal “segment n”(n = total

number of segments ≤5).

3. To verify that no segment paths contain more than n segments,

assign segment paths and numbers to all other terminals.

SIC Connection

3 3

. . . . . . . .

networksTRANSITION

12 3 45 678 9 10 1112

networksTRANSITION

12 3 4 5 6 7 8 9 10 11 12

. . . .

. . . . . . . .

networksTRANSITION

12 3 45 678 9 10 1112

networksTRANSITION

12 3 45 678 9 10 1112

. . . .

. . . . . . . .

. . . .

110-120

220-240

110-120 Orientation 220-240 Orientation

Fuse Holder Fuse Holder

Model 1004 12-Port Ethernet™Repeater Hub 6

Male AUI Connector/PC Connection

The male AUI card (E-AUI-

DC-SIC) provides a male

AUI connector for

connection, through an AUI

drop cable, to a 10Base5

port on a powered PC.

Fiber Optic Connector/10BaseFL Connection

The fiber optic card (E-FRL-SIC) provides one set of transmit (TX) and

receive (RX) ST connectors to fiber optic cable.

The redundant fiber optic card (E-FL/RED-SIC) provides a back-up fiber

optic connection by using two sets of transmit (TX) and receive (RX) ST

connectors to fiber optic cable.

Ensuring Correct 10BaseT Configuration

The 10BaseT cable and RJ-45 jacks for Hub to Terminal connections

must be configured as straight through. The 10BaseT cable and RJ-45

jacks for Hub to Hub connections must be configured as crossover.

NOTE: When installing the 1004 Hub using the MDI port, a crossover

cable is not needed. The MDI switch can be used to change the

straight through configuration to crossover at port 1.

The two active pairs

in a 10BaseT network

are pins 1 & 2 and

pins 3 & 6. Use only

dedicated wire pairs

(such as blue/white &

white/blue,

orange/white &

white/orange) for the

active pins.

Straight Through Cable

at RJ-45 Plug

Hub . . . . . . . . . . . . . . . .PC, transceiver, NIC, printer

RJ-45 Male . . . . . . . . . . . . . . .RJ-45 Male

1 . . . . . . . . . . . . . . . . . . .1

2 . . . . . . . . . . . . . . . . . .2

3 . . . . . . . . . . . . . . . . . .3

6 . . . . . . . . . . . . . . . . . . .6

18RJ-45PLUG

RJ-45JACK

234567

up to 2000 meters

Crossover Cable

at RJ-45 Plug

Hub . . . . . . . . . . . . . . .Hub

RJ-45 Male . . . . . . . . . . . . . . .RJ-45 Male

1 . . . . . . . . . . . . . . . . . . .3

2 . . . . . . . . . . . . . . . . . . .6

3 . . . . . . . . . . . . . . . . . .1

6 . . . . . . . . . . . . . . . . . .2

Model 1004 12-Port Ethernet™Repeater Hub 12

3. INSTALLATION

To install the Model 1004 Repeater Hub:

•Unpack the Model 1004 Repeater Hub.

•Install Model 1004 Repeater Hub on flat surface.

•Optionally install Slide In Card.

•Connect Cable to SIC and RJ-45 connectors.

•Connect Model 1004 Repeater Hub to power.

Direction is provided in the pages that follow.

Unpacking the Model 1004 Repeater Hub

The Model 1004 Repeater Hub packing contents should include the

following:

Item Part Number

Model 1004 Repeater

Hub E-TBT-HB-1004

Power Cord 3344, 3347, 3348, 3349, or 3523,

(depending upon power configuration

in country where installed)

User’s Guide 7366

In addition, any of the following optional SICs may be included:

Item Part Number

Thinnet Coaxial E-CX-SIC

Fiber Optic E-FRL-SIC

Twisted Pair E-TBT-SIC

Female AUI E-AUI-DT-SIC

Male AUI E-AUI-DC-SIC

Bridge E-BR-SIC

Redundant Fiber Optic E-FL/RED-SIC

Female AUI Connector/10Base5 or Transceiver

Connection

The female AUI card (E-AUI-DT-SIC) provides a female AUI connecto.r

for connection to 10Base5 through an AUI drop cable or to 10Base2,

10BaseT, or10BaseFL through a transceiver NOTE: The bridge card (E-

BR-SIC) also provides a female AUI connector.

Connecting 10Base5 Using AUI Drop Cable

To connect 10Base5 Cable to a

female AUI connector:

1. Locate or build IEEE 802.3

compliant AUI drop cable.

2. Connect AUI drop cable

male connector to the

female AUI (DTE) connector

on repeater.

3. Connect AUI drop cable female connector to the AUI port on

a transceiver or media attachment unit (MAU).

Connecting to Network Using Transceiver

To connect to a network using transceiver:

1. Locate IEEE 802.3 compliant transceiver with male AUI

connector and correct network media connector.

2. Connect transceiver male AUI connector to the female AUI

connector.

3. Connect transceiver network media connector to the network

media.

TOFIBER, COAX,

RTWISTED PAIR

Tabla de contenidos

Otros manuales de Cambiar de Transition Networks

Transition Networks

Transition Networks SM8T2DPA Manual de usuario

Transition Networks

Transition Networks LAN MASTER 33022.B Manual de usuario

Transition Networks

Transition Networks SM8TAT2SA-DC Manual de usuario

Transition Networks

Transition Networks SM TAT4X Series Manual de usuario

Transition Networks

Transition Networks SISPM1040-582-LRT Manual de usuario

Transition Networks

Transition Networks SESPM1040-541-LT Series Manual de usuario

Transition Networks

Transition Networks LANMaster T8-FL Manual de usuario

Transition Networks

Transition Networks E-PSW-TX-02 Manual de usuario

Transition Networks

Transition Networks SISGM-CHAS L2 Manual de usuario

Transition Networks

Transition Networks SISTM1040-262D-LRT-B Instrucciones de funcionamiento y mantenimiento

Transition Networks

Transition Networks SM8TAT2SA Manual de usuario

Transition Networks

Transition Networks SM8TAT2SA Manual de instrucciones

Transition Networks

Transition Networks SM24T6DPA Manual de usuario

Transition Networks

Transition Networks SISTP10xx-141-LR(T) Manual de usuario

Transition Networks

Transition Networks E-TBT-HB-0400 Manual de usuario

Transition Networks

Transition Networks E-TBT-HB-1600 Manual de usuario

Transition Networks

Transition Networks SISTF10xx-130-LR(T) Manual de usuario

Transition Networks

Transition Networks SM4T4DPA Manual de usuario

Transition Networks

Transition Networks SISPM1040-3-L Series Manual de usuario

Transition Networks

Transition Networks E-TBT-HB-1002 Manual de usuario

Transition Networks

Transition Networks MIL-S2400S Manual de usuario

Transition Networks

Transition Networks SISPM1040-384-LRT-C Manual de usuario

Transition Networks

Transition Networks SISPM1040-3 L Series Manual de usuario

Transition Networks

Transition Networks SISPM1040-3248-L Instrucciones de funcionamiento y mantenimiento

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario