Transition Networks CFETF1011-105 Manual de usuario

Installation . . . . . . . . . . . . . . . . . .2

Operation . . . . . . . . . . . . . . . . . . .5

Cable Specifications . . . . . . . . . . .7

Technical Specifications . . . . . . . .9

Troubleshooting . . . . . . . . . . . . .10

Compliance Information . . . . . . .12

User’s Guide

CFETF10xx-105

Slide-in-Module Media Converter

• Fast Ethernet™

• Copper to Fiber

• 100Base-TX to 100Base-FX

Transition Networks CFETF10xx-105 series Fast

Ethernet™ 100Base-TX to 100Base-FX media

converters (designed to be installed in a

PointSystem™ chassis) connect 100Base-TX twisted-

pair copper cable to multimode or single mode

100Base-FX fiber-optic cable.

*Typical maximum cable distance. Actual distance is dependent upon the physical

characteristics of the network installation.

Part Number Port One - Copper

100Base-TX

Port Two - Fiber-Optic

100Base-FX

CFETF1011-105 RJ-45

100 m (328 ft)*

ST, 1300 nm multimode

2 km (1.2 miles)*

CFETF1013-105 RJ-45

100 m (328 ft)*

SC, 1300 nm multimode

2 km (1.2 miles)*

CFETF1014-105 RJ-45

100 m (328 ft)*

SC, 1300 nm single mode

20 km (12.4 miles)*

CFETF1015-105 RJ-45

100 m (328 ft)*

SC, 1300 nm single mode

40 km (24.9 miles)*

CFETF1016-105 RJ-45

100 m (328 ft)*

SC, 1310 nm single mode

60 km (32.3 miles)*

CFETF1017-105 RJ-45

100 m (328 ft)*

SC, 1550 nm single mode

80 km (49.7 miles)*

CFETF1018-105 RJ-45

100 m (328 ft)*

MT-RJ, 1300 nm multimode

2 km (1.2 miles)*

CFETF1019-105 RJ-45

100 m (328 ft)*

LC, 1310 nm single mode

20 km (12.4 miles)*

CFETF1039-105 RJ-45

100 m (328 ft)*

LC 1300 nm multimode

2 km (1.2 miles)*

CFETF10xx-105

224-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Installation

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when setting the 4-position switch and the jumper and when

installing the slide-in-module media converter. Failure to observe this caution

could result in damage to, and subsequent failure of, the media converter.

Set the 4-Position Switch

• The 4-position switch is located

on the circuit board.

• Use a small flat-blade screwdriver

or a similar device to set the

recessed switches (see the

drawing to the right).

1. Auto-Negotiation™

up Advertises 100 Mb/s full-duplex and half-duplex (only during

Auto-Negotiation). (See page 5.)

down Disable Auto-Negotiation.

2. Link Pass-Through

up Enable Link Pass-Through. (See page 6.)

down Disable Link Pass-Through.

3. AutoCross™

up Enable AutoCross™ - The media converter connects automatically

to either straight-through or crossover twisted-pair copper cable.

(See page 5.)

down Disable AutoCross™ - Either straight-through or crossover twisted-

pair copper cable must be installed, according to the site

requirements.

4. (not used)

Set the Hardware/Software Jumper

The hardware/software jumper is located on the media converter circuit

board. Use small needle-nosed pliers or a similar device to set the jumper.

Refer to the drawings below when setting the media converter for hardware or

software mode.

Hardware The media converter mode is determined by

the 4-position switch settings listed above.

Software The media converter mode is determined by

the most-recently saved, on-board

microprocessor settings.

Software Mode

Hardware Mode

Not Used

Link Pass-Through (up=Enable)

AutoCross (up=Enable)

uto-Negotiation (up=Enable)

1234

[email protected] -- Click the “Transition Now” link for a live Web chat. 3

Installation -- Continued

Install the Slide-In-Module

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when installing the CFETF10xx-105 slide-in-module media

converter. Failure to observe this caution could result in damage to, and

subsequent failure of, the media converter.

1. Carefully slide the slide-in-module into the installation slot, aligning the

module with the installation guides.

2. Ensure that the module is firmly seated inside the chassis.

3. Push in and rotate the attached panel fastener screw clockwise to secure

the module to the chassis front.

Connect the Twisted-Pair Copper Cable

1. Locate or build 100Base-TX compliant cables, with male RJ-45

connectors installed at both ends.

2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on

the CFETF10xx-105 media converter.

3. Connect the RJ-45 connector at the other end of the cable to the RJ-45

port on the other device (switch, workstation, etc.).

CFMFF100 CFMFF100

CETCF100 CFETF100

CFETF110

CFMFF100

SPD PWR

FRX

CRX

FLNK

CLNK

10/100TX

10/100SX

100BASE-TX

100BASE-FX

LinkAlert

050½

LA PWR

RXF

RXC

LNK

COL

LKS

PWR

LKM

10BASE-2

10BASE-FL

LKS

PWR

LKM

LKS

PWR

LKM

Multimode

Singlemode

Multimode

Singlemode

Multimode

Singlemode

TERM

INIT

LNK

PWR

CPSMM120

SERIAL

10BASE-T

PWR

TX FX

100BASE-TX

100BASE-FX

panel fastener screw

RJ-45 port

on the other device

(switch, work station, etc.)

RJ-45 port

on the media

converter

CFETF10xx-105

424-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Installation -- Continued

Connect the Fiber Cable

1. Locate or build 100Base-FX compliant fiber cable with male, two-

stranded TX to RX connectors installed at both ends.

2. Connect the fiber cables to the CFETF10xx-105 media converter as

described:

• Connect the male TX cable connector to the female TX port.

• Connect the male RX cable connector to the female RX port.

3. Connect the fiber cables to the other device (another media converter,

hub, etc.) as described:

• Connect the male TX cable connector to the female RX port.

• Connect the male RX cable connector to the female TX port.

Power the Media Converter

The slide-in-module media converter is powered through the Transition

Networks PointSystem™ chassis.

Connect the fiber cable

to the media converter

as shown.

Connect the fiber cable

to the other device

(media converter,

hub, etc.) as shown

[email protected] -- Click the “Transition Now” link for a live Web chat. 5

Operation

Status LEDs

The CFETF10xx-105 media converter is designed to operate without user

intervention. Use the status LEDs to monitor the media converter operation in

the network.

PWR On = Connection to external AC power.

FX On = A link has been established for the fiber connection.

Flashing = The fiber connection is receiving data.

TX On = A link has been established for the copper connection.

Flashing = The copper connection is receiving data.

Product Features

Auto-Negotiation™

The Auto-Negotiation feature allows the CFETF10xx-105 media converter to

automatically configure itself to achieve the best possible mode of operation

over a link. The media converter broadcasts its speed (100 Mb/s) and duplex

capabilities (full or half) to the other devices and negotiates the best mode of

operation. Auto-Negotiation allows quick and easy installation because the

optimal link is established automatically. No user intervention is required to

determine the best mode of operation.

A scenario where the media converter is linked to a non-negotiating device is

a case where the user may want to disable Auto-Negotiation. In this instance,

the mode of operation will drop to the least common denominator between

the two devices (e.g. 100 Mb/s, half-duplex). Disabling this feature gives the

user the ability to force the connection to the desired speed and duplex mode

of operation.

AutoCross™

When the AutoCross feature is activated, it allows either straight-through

(MDI) or crossover (MDI-X) copper cables to be used when connecting to

100Base-TX devices. AutoCross determines the characteristics of the

connection and automatically configures the unit to link up, regardless if the

copper cable is MDI or MDI-X configuration.

NOTE: Factory default is “enable AutoCross.” Transition networks

recommends leaving the device in the “enable” mode.

PWR

TX FX

CFETF105

CFETF10xx-105

624-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Operation -- Continued

Link Pass-Through

When the Link Pass-Through feature is activated (see page 2), the media

converter monitors both the fiber and copper RX (receive) ports for loss of signal.

In the event of a loss of an RX signal (1), the media converter will automatically

disable the TX (transmit) signal (2), thus, “passing through” the link loss (3). The

far-end device is automatically notified of the link loss (4), which prevents the

loss of valuable data unknowingly transmitted over an invalid link.

Full-Duplex Network

In a full-duplex network, maximum cable lengths are determined by the type of

cables that are used. See page 1 (front cover) for the cable specifications for the

different CFETF10xx-105 models.

The 512-Bit Rule does not apply in a full-duplex network.

Half-Duplex Network (512-Bit Rule)

In a half-duplex network, the maximum cable lengths are determined by the

round trip delay limitations of each Fast Ethernet™ collision domain. (A

collision domain is the longest path between any two terminal devices, e.g. a

terminal, switch, or router.)

The 512-Bit Rule determines the maximum length of cable permitted by

calculating the round-trip delay in bit-times (BT) of a particular collision

domain. If the result is less than or equal to 512 BT, the path is good.

For more information on the 512-Bit Rule, see the white paper titled “Collision

Domains” on the Transition Networks website at: www.transition.com.

Media

Converter A

Media

Converter B

Near-End

Device

Far-End

Device

original fault

on the copper link media converter B

disables the copper lin

media converter A

disables the fiber TX link

media converter B

loses the fiber RX link

[email protected] -- Click the “Transition Now” link for a live Web chat. 7

Cable Specifications

Copper Cable

Category 5:

Gauge 24 to 22 AWG

Attenuation 22.0 dB /100m @ 100 MHz

Maximum Cable Distance 100 meters

• Straight-through (MDI) or crossover (MDI-X) twisted-pair cable may be used.

• Shielded (STP) or unshielded (UTP) twisted-pair cable may be used.

• Pins 1&2 and 3&6 are the two active pairs in an Ethernet™ network .

• Use only dedicated wire pairs for the active pins:

(e.g., blue/white & white/blue, orange/white & white/orange, etc.)

• Do not use flat or silver satin wire.

Fiber Cable

The physical characteristics must meet or exceed IEEE 802.3™ specifications.

Bit Error Rate: <10-9

Single mode fiber (recommended): 9 µm

Multimode fiber (recommended): 62.5/125 µm

Multimode fiber (optional): 100/140, 85/140, 50/125 µm

Crossover Cable

Straight-Through Cable

Twisted Pair #1

Twisted Pair #2

Operation -- Continued

SNMP

See the on-line documentation that comes with Transition Networks

FocalPoint™ software for applicable commands and usage.

Use SNMP at an attached terminal or at a remote location to monitor the media

converter by monitoring:

• Media converter power

• Copper link and fiber link status

• Hardware switch settings

• Fault condition

Also, use SNMP to enter network commands that:

• Enable/disable full- / half-duplex

• Enable/disable Link Pass-Through (LPT)

• Power down the media converter

CFETF10xx-105

824-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Cable Specifications -- Continued

CFETF1011-105 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

CFETF1013-105 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

CFETF1014-105 1300 nm single mode

Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber-optic Receiver Sensitivity: min: -31.0 dBm max: -8.0 dBm

Link Budget: 16.0 dB

CFETF1015-105 1300 nm single mode

Fiber-optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 26.0 dB

CFETF1016-105 1310 nm single mode

Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 29.0 dB

CFETF1017-105 1550 nm single mode

Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 29.0 dB

CFETF1018-105 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -33.5 dBm max: -14.0 dBm

Link Budget: 14.5 dB

CFETF1019-105 1310nm single mode

Fiber-optic Transmitter Power: min: -15.2 dBm max: -8.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.5 dBm max: -3.0 dBm

Link Budget: 17.3 dB

CFETF1039-105 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

The fiber optic transmitters on this device meet Class I Laser safety

requirements per IEC-825/CDRH standards and comply with 21

CFR1040.10 and 21CFR1040.11.

[email protected] -- Click the “Transition Now” link for a live Web chat. 9

Technical Specifications

For use with Transition Networks Model CFETF10xx-105 or equivalent.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,

Subchapter J applicable at the date of manufacture.

Standards IEEE 802.3™

Data Rate 100 Mb/s

Dimensions 3.4" x 5.0" x 0.87" (86 x 182 x 22 mm)

Weight 3 oz (91 g) (approximate)

Power Consumption 3.5 watts, 200 mA @ 13.9 VDC

MTBF 406,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)

1,593,000 hours (Bellcore7 V5.0)

Environment Tmra*: 0 to 60°C (32 to 140°F )

Storage Temp: -20 to 85°C (-4 to 185°F )

Humidity 5 to 95%, non condensing

Altitude 0 to 10,000 feet

Warranty Lifetime

*Manufacturer’s rated ambient temperature: Tmra range for this slide-in-module

depends on the physical characteristics and the installation configuration of the

Transition Networks PointSystem™ chassis in which this slide-in-module will be

installed.

The information in this user’s guide is subject to change. For the most up-to-date

information on the CFETF10xx-105 media converter, view the user’s guide on-

line at: www.transition.com.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,

Subchapter J applicable at the date of manufacture.

CAUTION: Visible and invisible laser radiation when open. Do not stare into

the beam or view directly with optical instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other

than those specified herein may result in hazardous radiation exposure.

CFETF10xx-105

10 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

Troubleshooting

If the media converter fails, isolate and correct the failure by determining the

answers to the following questions and then taking the indicated action:

1. Is the PWR LED illuminated?

• Is the media converter slide-in-module installed properly in the

chassis?

• Is the power cord properly installed in the chassis and at the external

power source?

• Does the external power source provide power?

• Contact Technical Support: 1-800-260-1312 (Int’l: 00-1-952-7600).

YES

• Proceed to step 2.

2. Is the TX LED illuminated?

• Check the twisted-pair cables for proper connection.

• Contact Technical Support: 1-800-260-1312 (Int’l: 00-1-952-7600).

YES

• Proceed to step 3.

3. Is the FX LED illuminated?

• Check the fiber cables for proper connection.

• Verify that the TX and RX cables on the media converter are

connected to the RX and TX ports, respectively, on the other device.

• Contact Technical Support: 1-800-260-1312 (Int’l: 00-1-952-7600).

YES

• Proceed to step 4.

4. Is the TX LED flashing?

• If there is no activity on the 100Base-TX port, proceed to step 5.

• If there is activity on the 100Base-TX port, disconnect and reconnect

the 100Base-TX cable to restart the initialization process.

• Restart the workstation to restart the initialization process.

• Contact Technical Support: 1-800-260-1312 (Int’l: 00-1-952-7600).

YES

• Proceed to step 5.

5. Is the FX LED flashing?

• If there is no activity on the 100Base-FX port, continue below

• If there is activity on the 100Base-FX port, disconnect and reconnect

the 100Base-FX cable to restart the initialization process.

• Verify that the TX and RX cables on the media converter are

connected to the RX and TX ports, respectively, on the other device.

• Restart the workstation to restart the initialization process.

• Contact Technical Support: 1-800-260-1312 (Int’l: 00-1-952-7600).

YES

• Contact Technical Support: 1-800-260-1312 (Int’l: 00-1-952-7600).

[email protected] -- Click the “Transition Now” link for a live Web chat. 11

Technical Support

Technical support is available 24 hours a day.

US and Canada: 1-800-260-1312

International: 00-1-952-941-7600

Transition Now

Chat live via the Web with Transition Networks Technical Support.

Log onto www.transition.com and click the Transition Now link.

Web-Based Seminars

Transition Networks provides seminars via live web-based training.

Log onto www.transition.com and click the Learning Center link.

E-Mail

Ask a question anytime by sending an e-mail to our technical support staff.

[email protected]

Address

Transition Networks

6475 City West Parkway

Minneapolis, MN 55344, USA

telephone: 952-941-7600

toll free: 800-526-9267

fax: 952-941-2322

Declaration of Conformity

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 U.S.A.

Model: CFETF10xx-105 Series media converters

Part Number(s): CFETF1011-105, CFETF1013-105, CFETF1014-105, CFETF1015-105,

CFETF1016-105, CFETF1017-105, CFETF1018-105, CFETF1019-105

CFETF1039-105

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the

CFETF10xx-105

to which this declaration refers is in

conformity with the following standards.

CISPR 22:1993; EN 55022:1994+A1: 1995+A2:1997, Class A; EN 55024:1998; FCC Part

15 Subpart B; EN 61000-3-2:1995+A14:2000; EN 61000-3-3: 199521 CFR subpart J

I, the undersigned, hereby declare that the equipment specified above conforms to the above

Directive(s) and Standard(s).

September 19, 2005_____

Stephen Anderson, Vice-President of Engineering Date

Trademark Notice

All trademarks and registered trademarks are the property of their respective owners.

means - graphic, electronic, or mechanical - without written permission from Transition

Networks.

Printed in the U.S.A. 33205.E

Compliance Information

CISPR22/EN55022 Class A + EN55024

CE Mark

FCC Regulations

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference, in which case the user will be required to correct the

interference at the user's own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus

set out on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

European Regulations

Warning This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können

bei Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für

Gegenmaßnahmen verantwortlich.

Attention! Ceci est un produit de Classe A. Dans un environment domestique, ce produit

risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de

prende les measures spécifiques appropriées.

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-

Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der

Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über

Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer

Konformität.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Transition Networks

Transition Networks

Transition Networks TR-CF-01 Manual de usuario

Transition Networks

Transition Networks SSDTF1011-105 Manual de usuario

Transition Networks

Transition Networks SGFEB10 Series Manual de usuario

Transition Networks

Transition Networks E-PSW-SX-01(SC) Manual de usuario

Transition Networks

Transition Networks J/FE-CF-04 SMLC Manual de usuario

Transition Networks

Transition Networks CRS2F31-100 Series Manual de usuario

Transition Networks

Transition Networks SGFEB1040-140 Manual de usuario

Transition Networks

Transition Networks SBFTF10XX-10X Manual de usuario

Transition Networks

Transition Networks SCSCF3011-100 Manual de usuario

Transition Networks

Transition Networks SRS4F3111-100 Manual de usuario

Transition Networks

Transition Networks J/POE-CF-01(SC) Manual de usuario

Transition Networks

Transition Networks SBFTF10xx-1xx Manual de usuario

Transition Networks

Transition Networks CBFTF1011-100 Manual de usuario

Transition Networks

Transition Networks M/GE-PSW-PSE-01 Manual de usuario

Transition Networks

Transition Networks E-TBT-FRL-05(L) Manual de usuario

Transition Networks

Transition Networks CSETF1011 Manual de usuario

Transition Networks

Transition Networks CSETF1011-205 Manual de usuario

Transition Networks

Transition Networks J/E-CX-TBT-01 Manual de usuario

Transition Networks

Transition Networks C/E-R-TX-FX-01 Manual de usuario

Transition Networks

Transition Networks CFMFF1314-280 Manual de usuario

Transition Networks

Transition Networks SFMFF1314-280 Manual de usuario

Transition Networks

Transition Networks SWITCHABLE ETHERNET AND FAST ETHERNET... Manual de usuario

Transition Networks

Transition Networks C/E-100BTX-FRL-03 Manual de usuario

Transition Networks

Transition Networks E-100BTX-FX-04(LH) Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario