Transition Networks C/F-SM-MM-06 Manual de usuario

COMPLIANCE INFORMATION

UL Listed

C-UL Listed (Canada)

CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on

the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes

Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen

werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des

interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques

appropriées

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Printed in the U.S.A. 33056.C

The TRANSITION Networks C/F-SM-MM-06 series OC-12 Ethernet media

converters, designed to be installed in the TRANSITION Networks Media

Conversion Center, E-MCC-1600, connect 1300 nM OC-12 multimode fiber-

optic cable to 1300nM OC-12 singlemode fiber-optic cable.

OC-12 1300 Nanometer

Slide-In-Module Media Converter

C/F-SM-MM-06

USER’S GUIDE

wer Modules

edia

onversion

enter

Power

In Use

Power

In Use

anagement

odule

Power

Link

C/F- M-MM-06

OC12

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten

verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur

Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen

einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

C/F-SM-MM-06

Provides an RX (receive) and TX

(transmit) SC OC-12 connector to

1300nm multimode fiber-optic cable

and an RX (receive) and TX (transmit)

SC OC-12 connector to 1300nm

singlemode fiber-optic cable.

C/F-SM-MM-06(XL)

Provides an RX (receive) and TX

(transmit) SC OC-12 connector to

1300nm multimode fiber-optic cable

and an RX (receive) and TX (transmit)

SC OC-12 connector to 1300nm

singlemode extra-long-haul fiber-optic

cable.

C/F-SM-MM-06 in the Network . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . .3

Operation . . . . . . . . . . . . . . . . . . . . .4

Fault Isolation and Correction . . . . .5

Cable Specifications . . . . . . . . . . . . .6

Technical Specifications . . . . . . . . . .7

Compliance Information . . . . . . . . . .8

C/F-SM-MM-06 IN THE NETWORK

NOTE: This product is NOT a repeater. Therefore, maximum distances depend on

specific characteristics of the installation. The full distances of BOTH singlemode

and multimode fiber MAY NOT be supported in the same installation.

TECHNICAL SPECIFICATIONS

Standards ANSI TI.646-1995, ITU G.957

Dimensions 3.8" x 2.4" x 1.0" (97mm x 61mm x 25mm)

Weight 8 oz (approximate)

Power Consumption 5 watts

Environment Typical Operating Temperature: 0-50°C (32°to122°F)

Storage Temperature: -20 to 85°C

Humidity 10-90%, non condensing

Altitude 0-10,000 feet

Warranty Lifetime

DECLARATION OF CONFORMITY

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 USA

Model: C/F-SM-MM-06 Series Media Converters

Part Number(s): C/F-SM-MM-06, C/F-SM-MM-06(XL)

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the C/F-SM-MM-06 to which this declaration refers is

in conformity with the following standards.

EMC-CISPR 22: 1985 Class A; EN 55022: 1988 Class A; EN 50082-1:1992;

EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950

I, the undersigned, hereby declare that the equipment specified above conforms to the

above Directive(s) and Standard(s).

_January 1, 1997_____

Stephen Anderson, Vice-President of Engineering Date

CABLE SPECIFICATIONS

The physical characteristics of the cable must meet or exceed ANSI TI.646-1995

and ITU G.957 specifications.

Fiber Specifications

Bit error rate: ≤10-10

MULTIMODE

Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber

Optional: 100 / 140 µm multimode fiber

85 / 125 µm multimode fiber

50 / 125 µm multimode fiber

Wavelength : 1300 nM

Fiber Optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber Optic Receiver Sensitivity: min: -23.0 dBm max: -8.0 dBm

Minimum Cable Distance: 2 meters

Maximum Cable Distance: 2 kilometers

SINGLEMODE

C/F-SM-MM-06

Fiber Optic Cable Recommended: 9 µm singlemode fiber

Wavelength : 1300 nM

Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber-optic Receiver Sensitivity: min: -28.0 dBm max: -8.0 dBm

Minimum Cable Distance: 2 meters

Maximum Cable Distance: 15 kilometers

C/F-SM-MM-06(XL)

Fiber Optic Cable Recommended: 9 µm singlemode fiber

Wavelength : 1300 nM

Fiber-optic Transmitter Power: min: -3.0 dBm max: -2.0 dBm

Fiber-optic Receiver Sensitivity: min: -28.0 dBm max: -8.0 dBm

Minimum Cable Distance: 2 meters

Maximum Cable Distance: 40 kilometers

INSTALLATION

Install Slide-In-Module in E-MCC-1600 Chassis

NOTE: Media Converter Slide-in-Modules can be installed in any installation

slot, in any order.

1. Remove Media Converter Slide-in-Module protective plate from

selected installation slot by removing screw that secures plate to

front of E-MCC-1600.

2. Carefully slide Media Converter Slide-in-Module into installation

slot, aligning Media Converter Slide-in-Module with installation

guides.

NOTE: Ensure that the Media Converter Slide-in-Module is firmly

seated against the backplane.

3. Secure Media Converter Slide-in-Module to E-MCC-1600 chassis by

turnng Media Converter Slide-in-Module panel fastener screw

clockwise to tighten.

Install Cable

1. Locate or build fiber cable with male two-stranded TX to RX

connectors appropriate to the media converter installed at both

ends.

2. Connect cable to connector to TX location on media converter and

connect same cable strand to RX location on attached device.

3. Connect cable to connector to RX location on media converter and

connect same cable strand to TX location on attached device.

4. Repeat steps 1-3 for second fiber cable.

Power the Slide-In-Module

NOTE: The Media Converter Slide-In-Module is powered through the

E-MCC-1600 Media Conversion Center.

OPERATION

After installation, the media converter should function without operator

intervention.

Status LEDs

Use the status LEDs to monitor media converter

operation in the network.

P(o)w(e)r Steady green LED indicates connection to

external AC power.

Link Steady green LED indicates that

singlemode and/or multimode fiber link is

connected properly.

FAULT ISOLATION and CORRECTION

If the media converter fails, isolate and correct the failure by determining the

answers to the following questions and then taking the indicated action:

1. Is the P(o)w(e)r LED on the media converter illuminated?

• Is the media converter inserted properly into the chassis?

• Is the power cord properly installed in the chassis and at the

external power source?

• Does the external power source provide power?

• Contact Technical Support: (800) 260-1312.

YES

• Proceed to step 2.

2. Is the Multimode Link LED illuminated?

• Check fiber cables for proper connection.

• Verify that TX and RX cables on media converter are connected to

RX and TX ports, respectively, on the other device.

• Power-cycle the media converter.

• Refer to Tech Tips available at: http://www.transition.com

• Contact Technical Support: (800) 260-1312.

YES

• Proceed to step 3.

3. Is the Singlemode Link LED illuminated?

• Check fiber cables for proper connection.

• Verify that TX and RX cables on media converter are connected to

RX and TX ports, respectively, on the other device.

• Power-cycle the media converter.

• Refer to Tech Tips available at: http://www.transition.com

YES

• Contact Technical Support: (800) 260-1312.

C/F- M-MM-06

OC12

Tabla de contenidos

Otros manuales de Convertidor de medios de Transition Networks

Transition Networks

Transition Networks SPOEB1039-105 Manual de usuario

Transition Networks

Transition Networks J-CF-02 Manual de usuario

Transition Networks

Transition Networks 10BASE-2 Manual de usuario

Transition Networks

Transition Networks M/GE-PSW-SX-01 Manual de usuario

Transition Networks

Transition Networks C/B-CF-01(SC) Manual de usuario

Transition Networks

Transition Networks M/GE-xSW-SFP-01-xx-U Series Manual de usuario

Transition Networks

Transition Networks E-TBT-FRL-FD-01 Manual de usuario

Transition Networks

Transition Networks Milan Raven Series Manual de usuario

Transition Networks

Transition Networks SPSVT26xx-10x Manual de usuario

Transition Networks

Transition Networks SWITCHABLE ETHERNET AND FAST ETHERNET... Manual de usuario

Transition Networks

Transition Networks CETCT1020-100 Manual de usuario

Transition Networks

Transition Networks E-100BTX-FRL-03(SC) E-100BTX-FRL-03(SM) Manual de usuario

Transition Networks

Transition Networks SMACF10XX Manual de usuario

Transition Networks

Transition Networks M/E-PSW-FX-02 Manual de usuario

Transition Networks

Transition Networks SAPTF33xx-100 Manual de usuario

Transition Networks

Transition Networks AS4TEF10xx-10x Manual de usuario

Transition Networks

Transition Networks C/E-100BTX-FRL-03 Manual de usuario

Transition Networks

Transition Networks NANOMETER E-100BTX-SX-01 Manual de usuario

Transition Networks

Transition Networks SRS4F3111-100 Manual de usuario

Transition Networks

Transition Networks J/E-PSW-FX-01 Manual de usuario

Transition Networks

Transition Networks F-SM-MM-05 Manual de usuario

Transition Networks

Transition Networks CFETF1011-200 Manual de usuario

Transition Networks

Transition Networks CRS4Fxxxx-10x Manual de usuario

Transition Networks

Transition Networks SI-IES-111D-LRT Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario