Transition Networks SSDTF1011-105 Manual de usuario

Installation . . . . . . . . . . . . . . . . . .3

Operation . . . . . . . . . . . . . . . . . . .9

Cable Specifications . . . . . . . . . .10

Technical Specifications . . . . . . .12

Troubleshooting . . . . . . . . . . . . .13

Compliance Information . . . . . . .16

* Typical maximum cable distance. (Actual

distance is dependent upon the physical

characteristics of the network.)

Note: The SSDTF10xx-10x requires a CSU

between the converter and the Public

Telephone Network.

SSDTF1027-105 RJ-45

1.5 km (5,000 feet)*

ST, 1300 nm multimode

5 km (3.1 miles)*

Part Number Port One - Copper Port Two - Duplex Fiber-Optic

SSDTF1011-105 RJ-45

1.5 km (5,000 feet)*

ST, 850 nm multimode

2 km (1.2 miles)*

SSDTF1012-105 RJ-45

1.5 km (5,000 feet)*

ST, 1310 nm single mode

8 km (4.8 miles)*

SSDTF1013-105 RJ-45

1.5 km (5,000 feet)*

SC, 850 nm multimode

2 km (1.2 miles)*

SSDTF1014-105 RJ-45

1.5 km (5,000 feet)*

SC, 1310 nm single mode

20 km (12.4 miles)*

SSDTF1015-105 RJ-45

1.5 km (5,000 feet)*

SC, 1310 nm single mode

40 km (24.8 miles)*

SSDTF1016-105 RJ-45

1.5 km (5,000 feet)*

SC, 1310 nm single mode

60 km (37.3 miles)*

SSDTF1017-105 RJ-45

1.5 km (5,000 feet)*

SC, 1550 nm single mode

80 km (49.7 miles)*

SSDTF1018-105 RJ-45

1.5 km (5,000 feet)*

MT-RJ, 1300 nm multimode

2 km (1.2 miles)*

SSDTF1022-105 RJ-45

1.5 km (5,000 feet)*

ST, 1310 nm single mode

15 km (9.3 miles)*

SSDTF1025-105 RJ-45

1.5 km (5,000 feet)*

MT-RJ, 1310 nm single mode

20 km (12.4 miles)*

User’s Guide

SSDTF10xx-10x

Stand-Alone Media Converter

•T1 / E1 with Remote Management

• Copper to Fiber

Transition Networks SSDTF10xx-10x series media

converters encode and decode T1 or E1 twisted-pair

copper signals over fiber optic cable to extend the

distance and transmission reliability of high-speed

T1 or E1 data traffic. The device is framing independent (as ESF vs. D4) and supports all

common line codes (e.g., AMI, B8ZS, HDB3).

The SSDTF10xx-10x is designed to be installed in pairs. For example, install one

SSDTF1011-105 as the “local” media converter and another SSDTF1011-105 as the

“remote” media converter.

224-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

SSDTF10xx-10x

(TX) = transmit (RX) = receive

* Typical maximum cable distance. Actual distance is dependent upon the physical

characteristics of the network.

** SSDTF1029-105 and -106 are intended to be installed in the same network where

one is the local converter and the other is the remote converter.

*** SSDTF1029-107 and -108 are intended to be installed in the same network where

one is the local converter and the other is the remote converter.

Note: The chassis version of the media converter is CSDTF10xx-10x. For more

information, see the CSDTF10xx-10x user’s guide on-line at: www.transition.com

Optional Accessories (sold separately)

Part Number Port One - Copper Port Two - Single Fiber Optic

SSDTF1029-105 ** RJ-45

1.5 km (5,000 feet)*

SC, 1310 mn (TX)/1550 nm (RX)

single mode, 20 km (12.4 miles)*

SSDTF1029-106 ** RJ-45

1.5 km (5,000 feet)*

SC, 1550 mn (TX)/1310 nm (RX)

single mode, 20 km (12.4 miles)*

SSDTF1029-107 *** RJ-45

1.5 km (5,000 feet)*

SC, 1310 mn (TX)/1550 nm (RX)

single mode, 40 km (24.8 miles)*

SSDTF1029-108 *** RJ-45

1.5 km (5,000 feet)*

SC, 1550 mn (TX)/1310 nm (RX)

single mode, 40 km (24.8 miles)*

Part Number Description

SPS-1872-SA Optional External Power Supply; 18-72VDC Stand-Alone

Output: 12.6VDC, 1.0 A

SPS-1872-PS Optional External Power Supply; 18-72VDC Piggy-back;

Output: 12.6VDC, 1.0 A

E-MCR-04 12-Slot media converter Rack (includes universal internal power

supply) 17 x 15 x 5 in. (432 x 381 x 127 mm)

WMBL Optional Wall Mount Brackets

Length: 4.0 in. (102 mm), Fits converter length: 4.7 in. (119 mm)

WMBV Optional Vertical Mount Bracket; 5.0 in. (127 mm)

WMBD Optional DIN Rail Mount Bracket; 5.0 in. (127 mm)

WMBD-F Optional DIN Rail Mount Bracket (flat); 3.3in. (84 mm)

[email protected] -- Click the “Transition Now” link for a live Web chat. 3

Installation

CAUTION: Wear a grounding device and observe electrostatic discharge precautions

when setting the jumper and switches. Failure to observe this caution could result in

damage to, and subsequent failure of, the media converter.

Set the hardware/software jumper

The hardware/software jumper is located on the circuit board inside the media

converter housing.

Hardware: The media converter mode is determined

by the switch settings.

Software: The media converter mode is determined

by the most-recently saved, on-board

microprocessor settings.

To set the two-position jumper:

1. Using a small screwdriver, remove the four (4) screws that secure the cover and

carefully remove the cover from the media converter.

2. The jumper is located on the circuit board and is labeled “H” and “S”.

3. Using small needle-nosed pliers or similar device, move the jumper to the

desired position. (Refer to the above drawing.)

4. Carefully replace the cover on the media converter and replace the four (4)

screws that secure the cover to the media converter.

Set the MDI/MDI-X switch (hardware mode only)

The MDI/MDI-X switch is located on the side of the media converter. This switch

allows the network administrator to use straight-through cable in installations where

crossover configuration cable is required. Use a small flat-blade screwdriver or a

similar device to set the recessed switch.

Set the switch to MDI if using

straight-through copper cable to

connect two unlike devices.

Set the switch to MDI-X if using

crossover copper cable to connect

two like devices.

424-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

SSDTF10xx-10x

Installation -- Continued

Set the loop-back switch

Hardware mode:

The loop-back switch is located on the front panel of the media converter and is

used for installation and network debugging procedures.

To set the switch, use a small flat-blade screwdriver or a

similar device (see the drawing to the right).

CL (Copper loop-back) Enable loop-back on the local copper interface.

-- (Center Position) Normal operation.

FL (Fiber loop-back) Enable loop-back on the local fiber interface.

Software mode:

If both media converters are under software control, the network administrator can

initiate the loop-back test function on the copper interface (local or remote) or on

the fiber interface (local or remote). These four loop-back test scenarios are

described in detail on page 14.

Set the configuration switches

The configuration switches are located on the side of the media converter and are

used to configure the media converter for various network conditions.

The switches are labeled 1 through 8 on the media converter housing top. There are

two sets (a “left, SW 2” and a “right, SW 1”) each with four switches labeled 1

through 4 (see the drawing below).

Use a small, flat-blade screwdriver or a similar device to set the recessed switches.

Transmit all ones (switches 1 & 2, left set, SW 2)

The Transmit All Ones function allows the insertion of an “all ones” pattern on the

copper and/or fiber interface when the signal detect is lost, creating an alarm

condition at the device connected to the interface.

[email protected] -- Click the “Transition Now” link for a live Web chat. 5

Installation -- Continued

Switch 1, Copper -- transmit all ones

UP - Disables the transmit all ones

function on the copper interface.

DOWN - Transmits an “all ones” pattern

on the copper interface when the signal

detect on the fiber interface is lost.

Switch 2, Fiber -- transmit all ones

UP - Disables the transmit all ones function

on the fiber interface.

DOWN - Transmits an “all ones” pattern on

the fiber interface when the signal detect on

the copper interface is lost.

Select T1 configuration (switches 3 & 4, left set, SW2)

Use switches 3 and 4 to configure the media converter for T1 configuration.

Switch 3, long haul/short haul (T1 only)

UP - Short haul.

DOWN - Long haul.

Switch 4, T1 / E1

UP - T1 configuration.

Set switches 1, 2, 3, and 4 on the right

set for the required network cable

settings (see pages 6 and 7).

Select E1 configuration (switch 4, left set, SW 2)

Use switch 4 to configure the media converter for E1 configuration.

Switch 4, T1 / E1

DOWN- E1 configuration.

The default network cable setting is 3.0 V, 120

ohm.

Switch 3 on the left set and switches 1, 2, 3, and

4 on the right set are disabled.

624-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

SSDTF10xx-10x

Installation -- Continued

Settings for T1 configuration (right switch set, SW 1)

T1/long-haul signal

Use switches 3 and 4 on the left switch set to select T1/long-haul signal (see the

drawing below).

Use switches 1 and 2 on the right switch set to select the proper network cable

settings. The drawing below lists the four options.

(Switches 3 and 4 on the right switch

set are not used for configuring

T1/long- haul signals.)

[email protected] -- Click the “Transition Now” link for a live Web chat. 7

Installation -- Continued

T1/short-haul signal

Use switches 3 and 4 on the left switch set to select T1/short-haul signal (see the

drawing below).

Use switches 1, 2, and 3 on the right switch set to select the proper network cable

settings. The drawing below lists the seven options.

(Switch 4 on the right switch set is

not used for configuring T1/short-

haul signals.)

824-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

SSDTF10xx-10x

Installation -- Continued

Install the copper cable

1. Locate or build twisted-pair copper cables that are compliant with the

specifications on page 11 with RJ-45 connectors at both ends.

2. Ensure that the MDI/MDI-X switch is set according to the network conditions

(see page 3).

3. Connect the RJ-45 connector at one end of cable to the RJ-45 port on the

media converter.

4. Connect the RJ-45 connector at the other end of the cable to the RJ-45 port on

the other device (switch, workstation, etc.).

Install the fiber cable

1. Locate or build fiber cables with male, two-stranded TX to RX connectors

installed at both ends.

2. Connect the fiber cables to the local SSDTF10xx-10x media converter as

described:

• Connect the male TX cable connector to the female TX port.

• Connect the male RX cable connector to the female RX port.

3. Connect the fiber cables to the remote SSDTF10xx-10x media converter as

described:

• Connect the male TX cable connector to the female RX port.

• Connect the male RX cable connector to the female TX port.

[email protected] -- Click the “Transition Now” link for a live Web chat. 9

Operation

After installation, the media converter should function without operator

intervention. Use the status LEDs to monitor the media converter operation in the

network.

SDC (Signal Detect/Copper) ON = the twisted-pair copper link is up.

SDF (Signal Detect/Fiber) ON = the fiber link is up.

PWR (Power) ON = the media converter is connected to

external power.

Dry-contact relay

The RJ-45 copper port has a dry-contact relay

that opens if the power, signal detect/copper, or

signal detect/fiber are lost. The operational

rating on pins 3 and 6 are 0-30 VDC, 100 mA

(maximum).

Remote management function

A remote, stand-alone media converter (revision SSDTF10xx-105 or higher) can be

managed when connected to a local CSDTF10xx-105 media converter. Please note

that in a managed network, both the local and remote media converters must be set to

“software” mode (see page 3). For more information, see the SNMP section in the

CSDTF10xx-10x manual online at: www.transition.com

Installation -- Continued

Power the media converter

Note: The external power supply provided with this product is UL listed by the

power supply’s manufacturer.

1. Install the power adapter cord to the back of the media converter.

2. Connect the power adapter plug to AC power.

3. Verify that the media converter is powered by observing the illuminated LED

power indicator light.

For DC power, consult the user’s guide for the Transition Networks SPS1872-xx

DC external power supply for powering the media converter.

10 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

SSDTF10xx-10x

Cable Specifications

Fiber cable

single mode fiber (recommended): 9 μm

Multimode fiber (recommended): 62.5/125 μm

Multimode fiber (optional): 100/140, 85/140, 50/125 μm

SSDTF1011-105 850 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm

Link Budget: 13.5 dB

SSDTF1012-105 1310 nm single mode

Fiber-optic Transmitter Power: min: -27.0 dBm max: -10.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -14.0 dBm

Link Budget: 7.0 dB

SSDTF1013-105 850 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm

Link Budget: 13.5 dB

SSDTF1014-105 1310 nm single mode

Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber-optic Receiver Sensitivity: min: -31.0 dBm max: -8.0 dBm

Link Budget: 16.0 dB

SSDTF1015-105 1310 nm single mode

Fiber Optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm

Fiber Optic Receiver Sensitivity: min: -38.0 dBm max: -8.0 dBm

Link Budget: 30.0 dB

SSDTF1016-105 1310 nm single mode

Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm

Fiber-optic Receiver Sensitivity: min: -38.0 dBm max: -8.0 dBm

Link Budget: 33.0 dB

SSDTF1017-105 1550 nm single mode

Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 29.0 dB

SSDTF1018-105 1300 nm multimode

Fiber-optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber-optic Receiver Sensitivity: min: -33.5 dBm max: -14.0 dBm

Link Budget: 14.5 dB

SSDTF1022-105 1310 nm single mode

Fiber Optic Transmitter Power: min: -15.0 dBm max: -5.0 dBm

Fiber Optic Receiver Sensitivity: min: -25.0 dBm max: -14.0 dBm

Link Budget: 10.0 dB

SSDTF1025-105 1310 nm single mode

Fiber-optic Transmitter Power: min: -11.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm

Link Budget: 9.0 dB

[email protected] -- Click the “Transition Now” link for a live Web chat. 11

Cable Specifications -- Continued

Fiber cable

SSDTF1027-105 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -10.0 dBm

Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm

Link Budget: 13.5 dB

SSDTF1029-105 1310 nm (TX)/1550 nm (RX) simplex

Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

SSDTF1029-106 1550 nm (TX)/1310 nm (RX) simplex

Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

SSDTF1029-107 1310 nm (TX)/1550 nm (RX) simplex

SSDTF1029-108 1550 nm (TX)/1310 nm (RX) simplex

Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm

Link Budget: 25.0 dB

The fiber optic transmitters on this device meet Class I Laser safety requirements

per IEC-825/CDRH standards and comply with 21 CFR1040.10 and

21CFR1040.11.

Copper cable

Connector: RJ-45 / RJ-48C

Elec. network connection: Single 4-wire (Tip/Ring - Tip1/Ring1)

Mechanical arrangement: 8-position miniature modular jack

Usage: 1.544 Mb/s or 2.0478 Mb/s access lines

Interface codes: 04DU9 (any applicable)

Cable type:

Long Haul T1: 0db, -7.5dp, -15db, -22db

E1 (120 ohm): E1 3.0V, 120

J1 (110 ohm): 0-655’, 110

DSX-1 (100 ohm): 0-133’, 133-266’, 266-399’,

399-533’, 533-655’

12 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

SSDTF10xx-10x

Technical Specifications

For use with Transition Networks Model SSDTF10xx-10x or equivalent

Standards: Emissions: CISPR A; Telecordia TR-NWT-001089

(designed to meet; NOT tested); FCC Part 68; T1/E1

Physical layer: ITU-T, ANSI, AT&T, and ETSI; European

Technical Standard: TBR 12; British Technical

Publication: PD 7024 : 1994 (NTR 4)

Dimensions: 3.25" x 4.7" x 1" (83 mm x 119 mm x 25 mm)

Weight: 10 oz. (283 g) approximately

Power consumption: 3.7 Watts

Power supply: 12VDC, 0.8A (North America, Europe, UK)

12VDC, 1.25A (NZ, Australia, S Africa, JP, Latin Am)

(The external power supply provided with this product

is UL listed by the power supply’s manufacturer.)

MTBF: 47,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)

116,000 hours (Bellcore7 V5.0)

Environment: 0°C to 50°C (32°F to 122° F )

Storage Temp: -15°C to 65°C (5°F to 149°F)

Humidity: 10 to 90%, non condensing

Altitude: 0 to 10,000 feet

Warranty: Lifetime

The information in this user’s guide is subject to change. For the most up-to-date

information on the SSDTF10xx-10x media converter, view the user’s guide on-line at:

www.transition.com.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,

Subchapter J applicable at the date of manufacture.

CAUTION: Visible and invisible laser radiation when open. Do not stare into the

beam or view directly with optical instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other than

those specified herein may result in hazardous radiation exposure.

[email protected] -- Click the “Transition Now” link for a live Web chat. 13

Troubleshooting

If the media converter fails, isolate and correct the failure by determining the answers

to the following questions and then taking the indicated action:

1. Is the PWR (Power) LED illuminated?

• Is the power adapter the proper type of voltage and cycle frequency for

the AC outlet? (See “Technical Specifications” on page 12.)

• Is the power adapter properly installed in the media converter and in the

outlet?

• Does the grounded AC outlet provide power?

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 2.

2. Is the SDC (Signal Detect/Copper) LED illuminated?

• Check the twisted-pair copper cable for the proper connection.

• Check the MDI/MDI-X switch for the correct twisted-pair copper cable

configuration (see page 3).

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 3.

3. Is the SDF (Signal Detect/Fiber) LED illuminated?

• Check the fiber cables for proper connection.

• Verify that the TX and RX cables on the local media converter are

connected to the RX and TX ports, respectively, on the remote media

converter.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 4.

14 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600

SSDTF10xx-10x

4. Is data transfer failing?

YES

• Verify the local copper connection by starting a local copper loop-back

(hardware mode: set the loop-back switch on the local media converter to

“CL”, software mode: enter the local copper loop-back command) and

then use a bit error test unit to run a bit error test.

• Verify the local fiber connection by starting a remote fiber loop-back

(hardware mode: set the loop-back switch on the remote media converter

to “FL”, software mode: enter the remote fiber loop-back command) and

then use a bit error test unit to run a bit error test.

• Verify the remote copper connection by starting a remote copper loop-back

(hardware mode: set the loop-back switch on the remote media converter

to “CL”, software mode: enter the remote copper loop-back command) and

then use a bit error test unit to run a bit error test.

• Verify the remote fiber connection by starting a local copper loop-back

(hardware mode: set the loop-back switch on the local media converter to

“FL”, software mode: enter the local fiber loop-back command) and then

use a bit error test unit to run a bit error test.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

[email protected] -- Click the “Transition Now” link for a live Web chat. 15

Technical support

Technical support is available 24 hours a day:

U.S.A. and Canada: 1-800-260-1312

International: 00-1-952-941-7600

Transition now

Chat live via the Web with Transition Networks Technical Support.

Log onto www.transition.com and click the Transition Now link.

Web-based seminars

Transition Networks provides seminars via live web-based training.

Log onto www.transition.com and click the Learning Center link.

E-Mail

Ask a question anytime by sending an e-mail to our technical support staff.

[email protected]

Address

Transition Networks

6475 City West Parkway

Minneapolis, MN 55344, U.S.A.

Telephone: 952-941-7600

Toll free: 800-526-9267

Fax: 952-941-2322

Declaration of Conformity

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 U.S.A.

Model: SSDTF10xx-10x Series Media Converter

Part Number: SSDTF1011-105, SSDTF1012-105, SSDTF1013-105,

SSDTF1014-105, SSDTF1015-105, SSDTF1016-105,

SSDTF1017-105, SSDTF1018-105, SSDTF1022-105,

SSDTF1025-105, SSDTF1027-105, SSDTF1029-105,

SSDTF1029-106, SSDTF1029-107, SSDTF1029-108

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the SSDTF10xx-10x to which this declaration refers is in

conformity with the following standards.

CISPR 22:1993; EN 55022:1994+A1:1995+A2:1997 Class A; EN 55024:1998; FCC

Part 15 Subpart B; EN 61000-3-2:1995+A14:2000; 61000-3-3:1995; CFR 21 subpart J

I, the undersigned, hereby declare that the equipment specified above conforms to the above

Directive(s) and Standard(s).

August 31, 2005

Stephen Anderson, Vice-President of Engineering Date

Compliance Information

CISPR22/EN55022 Class A + EN55024

CE Mark

FCC regulations

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which

case the user will be required to correct the interference at the user's own expense.

Canadian regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus

set out on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage

radioélectrique édicté par le ministère des Communications du Canada.

European regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses

Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für Gegenmaßnahmen

verantwortlich.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des

interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures spécifiques

appropriées.

Trademark notice

All trademarks and registered trademarks are the property of their respective owners.

graphic, electronic, or mechanical - without written permission from Transition Networks.

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-

Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der

Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über

Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer

Konformität.

SSDTF10xx-10x

16 Printed in the U.S.A. 33246.F

Otros manuales para SSDTF1011-105

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Transition Networks

Transition Networks

Transition Networks CEMTF1011-100 Manual de usuario

Transition Networks

Transition Networks E-TBT-FRL-1007 Manual de usuario

Transition Networks

Transition Networks C4TEF1011-100 Manual de usuario

Transition Networks

Transition Networks J/E-PSW-FX-01 Manual de usuario

Transition Networks

Transition Networks SFMFF1314-280 Manual de usuario

Transition Networks

Transition Networks M/GE-PSW-LX-01 Manual de usuario

Transition Networks

Transition Networks SISTG10 211-LR Series Manual de usuario

Transition Networks

Transition Networks CFMFF1314-210 Manual de usuario

Transition Networks

Transition Networks E-R-TX-FX-01(SC) Manual de usuario

Transition Networks

Transition Networks SRS4F3111-100 Manual de usuario

Transition Networks

Transition Networks E-MCR-02 Manual de usuario

Transition Networks

Transition Networks SGPOE1013-100 Manual de usuario

Transition Networks

Transition Networks CBFTF1011-100 Manual de usuario

Transition Networks

Transition Networks J/GE-CF-01(LX1) Manual de usuario

Transition Networks

Transition Networks SSETF10XX-200 Manual de usuario

Transition Networks

Transition Networks SBFTF10xx-1xx Manual de usuario

Transition Networks

Transition Networks SGPOE1013-100 Manual de usuario

Transition Networks

Transition Networks C/E-TBT-FRL-04(L) Manual de usuario

Transition Networks

Transition Networks ARCNET AR-CF-02 Manual de usuario

Transition Networks

Transition Networks CGETF1013-110 Manual de usuario

Transition Networks

Transition Networks SSDTF3011-110 Manual de usuario

Transition Networks

Transition Networks Stand-Alone Media Converter S4TEF10xx-11x Manual de usuario

Transition Networks

Transition Networks C/E-R-TX-FX-01 Manual de usuario

Transition Networks

Transition Networks E-100BTX-FX-N-02 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario