TPI PGM100 Manual de usuario

PGM100

Carbon Monoxide

Single Gas Monitor

The Value LeaderTM

www.tpi-thevalueleader.com

Contents

Agency Listings................................................... 1

Safety Information................................................ 2

General Description & Physical Specifications.............. 3

Product Features..................................................4

Sensor Specifications, Alarm Settings, Bump Testing..... 5

Adjust Date / Time................................................ 6

Alarm Adjustment.................................................7

Calibration......................................................... 8

Operation and Use................................................9-10

Warranty and Repair Policy..................................... 11

TPI PGM100

SINGLE GAS MONITOR

INSTRUCTION MANUAL

For use with Carbon Monoxide (CO)

Read and understand instructions before use.

Warning: To prevent ignition of flammable or combustible atmos-

pheres, disconnect power before servicing.

Warning: To reduce the risk of ignition of a flammable atmosphere, bat-

teries must only be changed in an area known to be nonflammable.

Avertissement: Pour reduire le risque d’fallumage d’fune atmosphere

inflammable, des batteries doivent seulement etre changees dans un

secteur connu pour etre inflammables.

IP65

EMC Directive (2004/108/EC)

EN 61000-4-2:1995, EN 61000-4-3:2002, EN 55011:2007

Class 1, Groups A, B, C & D

Exia, Temp code: T4

Safety Information

1. IMPORTANT:Read and understand this manual prior to use.

2. IMPORTANT:Oxygen instruments will show high readings for up to

30 minutes if taken from warm air to cold temperatures and vice-versa. For

best results let them "soak" in the ambient conditions prior to use.

3. WARNING: Substitution of components may impair intrinsic Safety.

4. WARNING: This instrument contains a lithium battery which may

leak or explode if improperly used. DO NOT DISPOSE OF IN A FIRE.

5. WARNING: Only service in an area known to be free of combustible

gases.

6. WARNING: Instruments are not certified intrinsically safe in environ-

ments above 21% oxygen.

7. WARNING: To verify operation prior to each day's use a function test

(bump test) should be performed. If the instrument does not pass this

test, full calibration should be performed.

8. WARNING: Keep all openings free from dirt, debris and foreign

objects.

9. WARNING: Do not use a damaged or improperly operating instru-

ment. Contact a service representative immediately.

ONLYzero instrument in a gas free environment

SEULEMENT l'instrument zéro dans un gas libèrent l'environnenment.

WARNING: To maintain intrinsic safety, service must be performed by fac-

tory authorized technicians with approved replacement parts only.

AVERTISSEMENT:Pour maintenir la sûreté intrinsèque, service doit être

exécuté par les techniciens autorisés par usine avec les pièces de rechange

approuvées seulement

General Description

The TPI PGM100 is an exceptionally rugged personal gas monitor. The

PGM100 is available in single gas configurations only. Preset alarms pro-

vide visual, audible and vibration alerts for low and high alarm conditions.

Built-in "Time Weighted Average" (TWA) and "Short Term Exposure Limit"

(STEL) alarms provide even greater margin of safety for the user. A cus-

tom display provides the user with easy to view information including gas

concentration, time remaining in months to sensor replacement, battery

low alert and activation of calibration process. (See Figure 1)

FUNCTION INDICATORS

• Battery Low

• Operation Time Remaining (months)

• Calibration

• High/Low Alarm Set Points:

Factory preset to OSHA requirements

• TWA/STEL Alarms: Preset to OSHA limits

• Other alarm settings available

• Data logging: Up to 100 alarm events

• Continuous "ON" Option

PHYSICAL SPECIFICATIONS

Operational Temp: -4 to 122° F (-20 to 50° C)

Humidity: 15-90% RH (Non-condensing)

Duty Cycle: Continuous

Response Time: T90 < 30 seconds

Alarms: Sound: 90 Db @ 12" (30cm)

Sight: Display Alerts 270° viewable LEDs

Touch: Vibration

Power Source: 3.6V Lithium Battery

Size: 3.81" x 2.31" x 0.8" (9.67 x 5.87 x 2 cm)

Weight: 3.6 oz. (105 g)

Battery Life: 2+ Years

Sensor: Electrochemical

Construction: Environmental resistance IP65

Impact resistant rubberized housing

Durable belt clip 3

Figure 1: Custom Display

PRODUCT FEATURES

The PGM100 is constructed of durable ABS plastic. The top housing is

additionally protected with a shock absorbing material to protect the

instrument from the rigors of field use. The front of the instrument has an

opening for the sensor and sounder. These are sealed to maintain the

integrity of the IP65 rating. Two buttons operate the instrument. The left

button is for power while the right is for zeroing and performing calibra-

tion. Multiple LED's beneath the frosted area create a very bright warning

even in bright sunlight.

The instrument is mounted using a sturdy suspender clip on the back of

the instrument. This instrument cannot be powered off or zeroed when in

alarm mode.

All sensors and batteries are designed for 2 years of continuous normal

use. The on-board memory will store up to 100 events or alarm condi-

tions. These can be downloaded through the use of SCal-100 with

SmartLink Software. Oldest events are over-written automatically when the

maximum is reached

Alarm LED / Optical Communication

Port.

Sensor

Sounder

On / Off

Zero / Calibrate

LCD Display

Belt Clip On Back

SENSOR SPECIFICATIONS

TYPE RESOLUTION RANGE

CO 1ppm 0-999

ALARMS

The PGM100 has two basic styles of alarm. Low Alarms activate at two second

intervals while High Alarms activate at one second intervals.

The sound, LEDs and vibrating motor are sequenced during alarms. The alarm

settings are controlled during the set-up of the product. All instruments are preset

for the standards that need to be adhered for various locations and needs. Fig. 2

shows examples of some of the alarm ranges.

Fig.2 STANDARD ALARM SETTINGS

Type Low High TWASTEL

CO 50 200 50 75

See page 7 for Alarm Adjustment instructions

FUNCTION (BUMP) TEST - MANUAL

Turn the instrument on and wait for the working display to illuminate. Apply an

approved concentration of gas to the sensor area using the PGM100 calibration

adapter. The flow should be 200-400 cc/min. The alarm should occur in less than

20 seconds.

To verify the operation of this product this test should be done prior to each day's

use. Failure to pass this test may indicate a product failure or the need for calibra-

tion.

ADJUST DATE/TIME

To adjust the PGM100 date/time manually, enter the menu by simultaneously pressing

both buttons then release them. (The PGM100 will force the user to update the time if it is

invalid during startup.) PGM100 will show "Pin". Press and release either button to show

"900". Press right button to increase the number to 925. Number will rollover to 900 when

it exceeds 998. Press and release the left button.

1. PGM100 will (beep continuously if invalid at startup and) show "rtc" until either button

is pressed and released.

2. PGM100 shows "Yr" until either button is pressed and released. PGM100 shows the

last two digits of the current year.

3. The number is increased by pressing the right button and will roll-over to 12 if it

exceeds 50. Adjust to desired "Yr".

4. Press and release the left button to accept it.

5. PGM100 turns on the Month icon and shows the current month.

6. The number is increased by pressing the right button and will roll-over to 01 if it

exceeds 12. Adjust to desired "MO".

7. Press and release the left button to accept it.

8. PGM100 shows "dd" until either button is pressed and released.

9. PGM100 shows the current date.

10. The number is increased by pressing the right button and will roll-over to 01 if it

exceeds the maximum number of days for the month specified. Adjust to desired "dd".

11. Press and release the left button to accept it.

12. PGM100 shows "Hr" until either button is pressed and released.

13. PGM100 shows the current hour in the 24-Hour format (no AM/PM selection)

14. The number can be increased by pressing the right button and will roll-over to 00 if it

exceeds 23. Adjust to desired "Hr".

15. Press and release the left button to accept it.

16. PGM100 shows "nn" until either button is pressed and released.

17. PGM100 shows the current minute .

18. The number can be increased by pressing the right button and will roll-over to

00 if it exceeds 59. Adjust to desired "nn".

19. Press and release the left button to accept it.

20. The PGM100 date/time have now been updated.

ALARM ADJUSTMENT

1. Press both buttons together when unit starts up and displays Gas Type and

then release it OR.

2. From working display, push both buttons simultaneously and release. The unit

will display Pin, press either key to display 900.

3. Press the Right button to scroll up to 980 and then push left button. The num-

ber increases to 998 and then restarts from 900. It will go to the menu to

adjust the alarm and display "Con" for Continuous On operation. Press Left

button to select. Press Right Button to toggle mode. Press Left button to save

the setting. It will now display "LO" for the low alarm.

4. Press Left button to adjust the "LO" alarm. The current setting will be displayed.

5. Press Right button to adjust the alarm. You can only increase the number.

Once it exceeds 300 it will start from 0.

6. Press Left button to save the alarm setting and it will now display "HI".

7. Press the Left button to adjust the "HI" alarm. The current setting will be dis-

played.

8. Press Right button to adjust the alarm. You can only increase the number.

Once it exceeds 300 it will start from 0.

9. Press Left button to save the alarm settings. It will now display "tA" for TWA.

10. Press Left button to adjust the TWA alarm. The current setting will be dis-

played.

11. Press Right button to adjust the alarm. You can only increase the number.

Once it exceeds 300 it will start from 0.

12. Press Left button to save the alarm settings. It will now display "StL" for

STEL.

13. Press Left button to adjust the STEL alarm. The current setting will be dis-

played.

14. Press Right button to adjust the alarm. You can only increase the number.

Once it exceeds 300 it will start from 0.

15. Press Left button to save the alarm settings. It will automatically exit the

menu and perform auto zero.

CALIBRATION

Turn on the PGM100 until the working display is illuminated. Wait for 2 minutes prior to

beginning the calibration process.

1. Prepare the approved gas cylinder and regulator with the calibration adapter attached.

The flow should be 200-400 cc/min.

2. Push and hold the Zero button until the display reads "GAS".

3. Attach the PGM100 calibration adapter.

4. Start the gas flow.

5. Push and release the Zero button. A changing number will flash as will the CAL icon.

6. Successful calibration is indicated when only the gas concentration is displayed. The

CAL icon will no longer be illuminated.

7. Bad calibration will be indicated by the word "BAD" and the CAL icon on the display.

Press the power button to acknowledge. (Retry calibration)

8. Successful calibration will be logged as an Alarm event in the log.

BUMP/CALIBRATION using SCal-100 (Sold Separately)

1. Prepare SCal-100 Station.

2. Turn PGM100 On and allow to Zero.

3. Install PGM100 into SCal-100 Station.

4. Remove PGM100 when test is complete

Tabla de contenidos

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario