Theben thePiccola P360-100 DE Manual de usuario
1
thePiccola P360-100 DE WH
2090200
307146 02
Presence detector
EN
1. Basic safety information 3
2. Proper use 3
Disposal 3
3. Device description 4
4. Installation and connection4
Installing the presence
detector 4
Connecting the presence
detector 6
Individual switching 7
Parallel switching 7
2
Push button control 8
Installation instructions and
detection area 8
5. Walking test 9
6. Setting 9
Setting the brightness
switching value (LUX) 10
Setting the time delay (TIME) 12
7. Settings with remote
control 12
Settings by using theSenda S 13
Settings by using theSenda P 13
Settings with Sendo Pro
868-A 15
8. Technical data 15
9. Contact 16
3
1. Basic safety information
Danger of death through electric shock or fire!
Installation should only be carried out by a
qualied electrician!
WARNING
•The device conforms with EN 60669-2-1 if correctly
installed
2. Proper use
•Presence detector for automatic lighting control depen-
dent on presence and brightness
•Suitable for ceiling installation (false ceilings)
•Suitable for small rooms, corridors, toilets, etc.
Disposal
Dispose of the device in an environmentally sound manner
(electronic waste)
4
3. Device description
Sensor unit
red LED
Power supply unit
2 potentiometers for setting
the time delay (TIME) and
the brightness switching
value (LUX)
4. Installation and connection
Installing the presence detector
LInstallation height: 2–4 m
LCable length: 45 cm
LPresence detector requires clear line of sight to people
5
Disconnect power source
Create a ceiling opening of Ø 34–36 mm
Connect power supply unit according to the
wiring diagram
Make settings at the potentiometers
Push the power supply unit through the ceiling opening
and attach the sensor with tensioned springs in the ceiling
Ø 34-36 mm
6–8 mm
max. 1 x 2,5 mm2
6
Connecting the presence detector
Danger of death through electric shock or fire!
Installation should only be carried out by a
qualied electrician!
WARNING
Disconnect power source
Ensure device cannot be switched on
Check absence of voltage
Earth and bypass
Cover or shield any adjacent live components
The warm-up phase takes approx. 1 min. The LED is perma-
nently red.
7
Individual switching
In individual switching, the presence detector as master
detects presence and brightness and controls lighting.
L’
Parallel switching
If the detection area covered by a single presence detector
is insufcient (in larger rooms), then the switch contacts of
several detectors can be directly connected with each other.
Set brightness switching value and time delay on all detec-
tors identically.
L’ L’
8
Push button control
The lighting can be manually switched on/off via a button. If
the light is switched on manually, it will remain on as long as
people are present (plus time delay). Then the light goes into
the set automatic mode. If the light is switched off manually,
it will remain off as long as people are present (plus time
delay). Then the light goes back to automatic mode.
Installation instructions and detection
area
As the detector reacts to variations in temperature, avoid the
following situations:
Do not point the presence detector at objects with highly-
reective surfaces such as mirrors, etc.
Do not install the presence detector near heat sources such
as heating vents, air conditioners, lamps, etc.
Do not point the presence detector at objects that move in
the wind such as curtains, large plants, etc.
Pay attention to the direction of motion during the test run.
2,5 m
360°
Ø 2 m
Ø 8 m
9
Lrecommended installation height: 2 – 4 m
LTransverse detection area: 8 m (transversal to the detector)
LFrontal detection area: 2 m (directly approaching the detector)
LDetection angle: 360°
5. Walking test
The walking test is used to test the detection area.
Set the time delay potentiometer (TIME) to T(Test). The
presence detector only reacts to movements, brightness
measurement is switched off.
Walk through the detection area. Every detected movement
is indicated by the LED, and the light switch contact closes.
When no one is present the light switch contact opens after
3 seconds.
3 sec
6. Setting
The presence detector has 2 potentiometers for setting time
delay (TIME) and brightness switching value (LUX).
10
Setting the brightness switching value
(LUX)
You can set different brightness values with the potentiome-
ter for the brightness switching value (LUX).
If you want to change the preset brightness
Set the potentiometer to the desired brightness (5 – 1000
lux = ).
Otros manuales para thePiccola P360-100 DE
1
Tabla de contenidos
Otros manuales de Sensor de seguridad de Theben
Theben
Theben thePrema S360-101 E UP WH Manual de usuario
Theben
Theben LUXA 104 S360-200-24 DE-UP WH Manual de usuario
Theben
Theben PlanoCentro A-KNX Instrucciones de uso
Theben
Theben theRonda S360 KNX UP WH Manual de usuario
Theben
Theben theMura S180-100 UP WH Manual de usuario
Theben
Theben ECO-IR 180EIB-AC Manual de usuario
Theben
Theben Luxa 103-200 Manual de usuario
Theben
Theben theLuxa S150 WH Manual de usuario
Theben
Theben TIMEGUARD LEDPROPCB Manual
Theben
Theben 201 0 090 Manual de usuario
Theben
Theben Timeguard PDSM361AB Manual
Theben
Theben compact office EIB Manual de usuario
Theben
Theben PlanoCentro 000-E Series Manual de usuario
Theben
Theben TA 4 S DALI-2 Manual de usuario
Theben
Theben theLeda D S AL Manual de usuario
Theben
Theben theRonda S360-100 UP WH Manual de usuario
Theben
Theben thePrema S360 DALI UP WH Manual de usuario
Theben
Theben PlanoSpot 360 DALI-2 S DE Series Manual de usuario
Theben
Theben theLeda D B AL Manual de usuario
Theben
Theben thePixa P360 KNX UP WH Manual de usuario
