Texas Instruments TS3USB221 Manual de usuario

User's Guide

SCDU001A–July 2009–Revised October 2009

TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2

Multiplexer/Demultiplexer Switch Evaluation Module

Contents

1 Preface ....................................................................................................................... 2

2 Introduction .................................................................................................................. 3

3 EVM Configuration and Description ...................................................................................... 5

4 Related Documentation ................................................................................................... 14

List of Figures

1 TS3USB221/A/E EVM Block Diagram ................................................................................... 3

2 Quick Start Evaluation...................................................................................................... 4

3 Jumpers J6, J7, and J8 Configuration ................................................................................... 5

4 EVM Schematic ............................................................................................................. 7

5 Top Silkscreen/Assembly .................................................................................................. 9

6 Top Metal (High-Speed Differential) .................................................................................... 10

7 Internal Ground Plane .................................................................................................... 11

8 Internal Power Plane...................................................................................................... 12

9 Bottom Metal (Low-Speed Single-Ended).............................................................................. 13

10 Bottom Silkscreen/Assembly............................................................................................. 13

List of Tables

1 EVM Jumper Description................................................................................................... 5

2 EVM Connector Description............................................................................................... 5

3 Board Stack-Up ............................................................................................................. 6

4 Bill of Materials............................................................................................................. 14

SCDU001A–July 2009–Revised October 2009 TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer

Switch Evaluation Module

ATTENTION

HANDLE ONLY AT

STATIC SAFE WORK STATIONS

STATIC SENSITIVE DEVICES

Preface

www.ti.com

1 Preface

1.1 About This Manual

This user’s guide describes the TS3USB221/A/E Evaluation Module (EVM). This guide contains the EVM

schematics, bill of materials, assembly drawings, and top and bottom board layouts.

1.2 How to Use This Manual

This document contains the following chapters:

• Chapter 1 – Preface

• Chapter 2 – Introduction and Quick Start

• Chapter 2 – EVM Configuration and Description

• Chapter 3 – Related Documents

1.2.1 Information about Cautions and Warnings

CAUTION

This EVM contains components that can potentially be damaged by

electrostatic discharge. Always transport and store the EVM in its supplied ESD

bag when not in use. Handle using an antistatic wristband. Operate on an

antistatic work surface. For more information on proper handling, see the

Electrostatic Discharge (ESD) application note (SSYA008).

The information in a caution or a warning is provided for your protection. Please read each caution and

warning carefully.

1.2.2 FCC Warning

This equipment is intended for use in a laboratory test environment only. It generates, uses, and can

radiate radio frequency energy and has not been tested for compliance with the limits of computing

devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonable

protection against radio frequency interference. Operation of this equipment in other environments may

cause interference with radio communications, in which case the user at his/her own expense will be

required to take whatever measures may be required to correct this interference.

2TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer SCDU001A–July 2009–Revised October 2009

Switch Evaluation Module Submit Documentation Feedback

TS3USB221/A/E EVM

TS3USB221/A/E

www.ti.com

Introduction

2 Introduction

The TS3USB221/A/E EVM is an evaluation module for the Texas Instruments (TI) 1:2

multiplexer/demultiplexer high-bandwidth USB switches. It is specially designed for high-speed USB 2.0

signals, supports bidirectional signaling, and offers high-bandwidth (1.1 GHz). When interfacing other USB

devices with this EVM, the switch allows signals to pass with minimum edge and phase distortion as well

as little or no signal attenuation.

This evaluation module is designed to demonstrate the small printed circuit board (PCB) areas that can be

achieved when designing with the TS3USB221/A/E USB switches. It is powered from the 5-V rail of the

USB input. Additionally, the TS3USB221/A/E provides an output enable input and an output select input

for flexible configuration of the USB. See Figure 1 for the EVM block diagram.

Figure 1. TS3USB221/A/E EVM Block Diagram

2.1 List of Hardware Items for Operation

The following items are required for EVM evaluation:

• The TS3USB221/A/E EVM

• USB cables with connector type depending on the surrounding system

The following items are optional for EVM evaluation:

• USB type A or type B connectors to change connectors J1 through J5 for optimal system interface

configuration

• IBM compatible PC with USB 2.0 ports for quick start evaluation

SCDU001A–July 2009–Revised October 2009 TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer

Switch Evaluation Module

TS3USB221/A/E EVM

TS3USB221/A/E

Introduction

www.ti.com

2.2 Quick Start

Figure 2. Quick Start Evaluation

1. Connect the PC to the USB connector J3 through a USB cable.

2. Make sure the 3.3-V LDO output is enabled by opening J8 without a jumper.

3. Make sure the TS3USB221/A/E IC is enabled by shunting J7 with a jumper.

4. Connect two USB downstream devices (for example, mouse, keyboard, USB memory stick, etc) to J4

and J5 on the EVM.

5. To select USB downstream device 1 connected to J4, make sure J6 is shunted with a jumper. To

select USB downstream device 2 connected to J5, make sure J6 is open without a jumper.

6. Connector J1 and J2 are connected together without a USB switch. This through-path can serve as a

reference to compare with the TS3USB221/A/E path.

4TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer SCDU001A–July 2009–Revised October 2009

Switch Evaluation Module Submit Documentation Feedback

TS3USB221/A/E

Output Select or

Ouput Enable

3.3-V LDO

Ouput Enable

10 kW10 kW

www.ti.com

EVM Configuration and Description

3 EVM Configuration and Description

3.1 EVM Description

To conform to the USB 2.0 specification, the differential traces D+ and D- lines on the board are

impedance matched to 90-Ωdifferential. The trace length of the through-path and the trace length through

the TS3USB221/A/E switch are also matched for comparison purpose. The PCB is a simple four-layer

top-side populated board (see the schematic and PCB layout in Section 3.4 and Section 3.5). The major

features of the hardware design are detailed in the following sections.

3.2 Jumper Configuration (J6 to J8)

The EVM has jumper J6 through J8 (see Figure 3) to provide configuration to the TS3USB221/A/E and the

3.3-V LDO. J6 allows switch output channel select, J7 provides switch enable control, and J8 provides

3.3-V LDO enable control. Table 1 lists all of the jumpers in the EVM and their respective functionality (all

default settings are in bold).

Figure 3. Jumpers J6, J7, and J8 Configuration

Table 1. EVM Jumper Description

Jumper Functionality Configuration

Shunt J6 to select output 1

J6 TS3USB221/A/E Select Open J6 to select output 2

Shunt J7 to enable the switch

J7 TS3USB221/A/E Enable Open J7 to disable the switch

Shunt J8 to disable the LDO

J8 3.3V LDO Enable Open J8 to enable the LDO

The EVM provides USB connectors J1 through J5 to interface with other USB devices. Depending on the

application need, the connectors can be de-soldered and changed to either type A or type B connector.

See Table 2 for the default connectors on the EVM.

Table 2. EVM Connector Description

Connector Functionality Configuration

Default as type B connector

J1 USB Connector Can be replaced with type A connector

Default as type A connector

J2 USB Connector Can be replaced with type B connector

Default as type B connector

J3 USB Connector Can be replaced with type A connector

Default as type B connector

J4 USB Connector Can be replaced with type A connector

Default as type B connector

J5 USB Connector Can be replaced with type A connector

SCDU001A–July 2009–Revised October 2009 TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer

Switch Evaluation Module

EVM Configuration and Description

www.ti.com

3.3 Board Stack-Up

Table 3 shows the board stack-up.

Table 3. Board Stack-Up

Subclass Thickness Dielectric Loss Width Impedance Coupling Spacing Diff Zo

Type Shield

Name (mils) Constant Tangent (mils) (Ω) Type (mils) (Ω)

1 SURFACE

2 TOP CONDUCTOR 2.4 1 0 7.5 47.72 EDGE 7.5 85.004

3 DIELECTRIC 4 4.1 0.035

4 GND PLANE 1.2 1 0 YES

5 DIELECTRIC 48 4.1 0.035

6 VCC PLANE 1.2 1 0 YES

7 DIELECTRIC 4 4.1 0.035 7.5 47.72 EDGE 7.5 85.004

8 BOTTOM CONDUCTOR 2.4 1 0

9 SURFACE

6TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer SCDU001A–July 2009–Revised October 2009

Switch Evaluation Module Submit Documentation Feedback

www.ti.com

EVM Configuration and Description

3.4 Schematics

Figure 4. EVM Schematic

SCDU001A–July 2009–Revised October 2009 TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer

Switch Evaluation Module

EVM Configuration and Description

www.ti.com

3.5 PCB Layout

Figure 5. Top Silkscreen/Assembly

8TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer SCDU001A–July 2009–Revised October 2009

Switch Evaluation Module Submit Documentation Feedback

www.ti.com

EVM Configuration and Description

Figure 6. Top Metal (High-Speed Differential)

SCDU001A–July 2009–Revised October 2009 TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer

Switch Evaluation Module

EVM Configuration and Description

www.ti.com

Figure 7. Internal Ground Plane

10 TS3USB221/A/E High Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer SCDU001A–July 2009–Revised October 2009

Switch Evaluation Module Submit Documentation Feedback

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments ADS8350EVM-PDK Manual de usuario

Texas Instruments

Texas Instruments TLV3802 Manual de usuario

Texas Instruments

Texas Instruments TPS25944XEVM-635 Manual de usuario

Texas Instruments

Texas Instruments BQ76PL536EVM-3 Manual de usuario

Texas Instruments

Texas Instruments BQ25303J Manual de usuario

Texas Instruments

Texas Instruments BQ25616J Manual de usuario

Texas Instruments

Texas Instruments DS320PR410-RSC-EVM Manual de usuario

Texas Instruments

Texas Instruments TLV320AIC32EVM Manual de usuario

Texas Instruments

Texas Instruments bq24070/1 Manual de usuario

Texas Instruments

Texas Instruments TMP451EVM Manual de usuario

Texas Instruments

Texas Instruments MSP-EXP430F5438 Manual de usuario

Texas Instruments

Texas Instruments DS90C189-Q1EVM Manual de usuario

Texas Instruments

Texas Instruments DAC9881 Manual de usuario

Texas Instruments

Texas Instruments DLP3030-Q1 Manual de usuario

Texas Instruments

Texas Instruments ADS7056EVM Manual de usuario

Texas Instruments

Texas Instruments SLAU039 Manual de usuario

Texas Instruments

Texas Instruments AFE539A4EVM Manual de usuario

Texas Instruments

Texas Instruments TMUX9832BGAEVM Manual de usuario

Texas Instruments

Texas Instruments ADS5120EVM Manual de usuario

Texas Instruments

Texas Instruments ADS54J42EVM Manual de usuario

Texas Instruments

Texas Instruments TSW1200EVM Manual de usuario

Texas Instruments

Texas Instruments TMS320C5545 BoosterPack Manual de instalación

Texas Instruments

Texas Instruments TLV320AIC23 Manual de usuario

Texas Instruments

Texas Instruments ADS58J64 EVM Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario