Texas Instruments LMX1906-SP Manual de usuario
EVM User's Guide: LMX1906EVM-CVAL
LMX1906-SP Evaluation Module
Description
The LMX1906-SP evaluation module (EVM) is
designed to evaluate the performance of the
LMX1906-SP, which is a four-output, ultra-low
additive jitter radio-frequency (RF) buffer, divider and
multiplier. The device can buffer RF frequencies up
to 18 GHz, multiply RF outputs up to 6.4 GHz,
and divide outputs by up to 6.4 GHz. This board
consists of an LMX1906-SP device and an integrated
USB2ANY programmer.
Features
• 300-MHz to 18-GHz output frequency
• 4 high-frequency clocks with corresponding
SYSREF outputs
– Shared divide by 2, 3, 4, 5, 6, 7 and 8
– Shared programmable multiplier ×2, ×3, and ×4
• 3.3-V supply voltage (with onboard 2.5-V LDOs) or
2.5-V supply voltage (with LDOs bypassed)
• –55ºC to +125ºC operating temperature (with
onboard MCU bypassed)
• Optional pin mode control without register
programming
Applications
• General purpose:
– Data converter clocking
– Clock distribution/multiplication/division
• Aerospace and defense:
–Radar
–Electronic warfare
–Seeker front end
– Phased array antenna/beam forming
www.ti.com Description
SNAU288 – DECEMBER 2023
Submit Document Feedback
LMX1906-SP Evaluation Module 1
Copyright © 2023 Texas Instruments Incorporated
1 Evaluation Module Overview
1.1 Introduction
The LMX1906-SP EVM is an ultra-low additive-jitter RF buffer, divider, and multiplier, with integrated SYSREF
generation capability. A separate auxiliary clock divider can be used for FPGAs or other logic ICs. Each RF
output (and the logic clock) is paired with a complementary SYSREF output with picosecond-precision delay-
tuning capability, and can be operated as a generator (with synchronization capability across multiple devices) or
as a repeater.
The EVM can be operated with a 3.3-V supply voltage when the onboard LDOs are utilized. The LDOs can be
bypassed, in this case the supply voltage is 2.5-V.
The EVM contains LMX1906-SP, two LDOs, a microcontroller and an IO expander. LMX1906-SP and the LDOs
can support –55ºC to +125ºC operation. For high temperature evaluation, use an USB2ANY dongle to control
the EVM.
1.2 Kit Contents
Included within each evaluation kit is:
• One LMX1906-SP EVM board (DC238) with integrated USB2ANY controller
• One USB cable
1.3 Specification
Table 1-1. LMX1906-SP EVM Specification
Parameter Value Conditions
Supply voltage (VCCIN SMA) 3.1 V to 3.5 V On-board voltage regulator outputs are 2.5 V
Supply current 1.3 A max. Various configurations
CLKIN input frequency
300 MHz to 18 GHz Buffer mode
150 MHz to 6.4 GHz Divider mode
3.2 to 6.4 GHz
Multiplier mode
CLK_MULT = ×1
1.6 to 3.2 GHz CLK_MULT = ×2
1.066 to 2.133 GHz CLK_MULT = ×3
800 MHz to 1.6 GHz CLK_MULT = ×4
1.4 Device Information
The high-frequency capability and extremely low jitter of this device, makes a great design to clock precision,
high-frequency data converters without degradation to the signal-to-noise ratio. Each of the four high-frequency
clock outputs, and additional LOGICLK output with larger divider range, is paired with a SYSREF output clock
signal. The SYSREF signal for JESD interfaces can either be internally generated or passed in as an input and
re-clocked to the device clocks. For data converter clocking applications, to have the jitter of the clock be less
than the aperture jitter of the data converter is critical. In applications where more than four data converters must
be clocked, a variety of cascading architectures can be developed using multiple devices to distribute all the
high-frequency clocks and SYSREF signals required. With low jitter and noise floor, this device combined with
an ultra-low noise reference clock source is an exemplary design for clocking data converters, especially when
sampling above 3 GHz.
Evaluation Module Overview www.ti.com
2LMX1906-SP Evaluation Module SNAU288 – DECEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
2 Hardware
2.1 Setup
2.1.1 Evaluation Setup Requirement
At a minimum, evaluation of the buffer mode requires:
• A DC power supply capable of at least 3.1 V, 2 A
• A high-quality signal source, such as an SMA100B
• A spectrum analyzer or signal analyzer
• A PC with a USB port, running Windows 7 or a more recent version of Windows
• Texas Instruments Clocks and Synthesizers TICS Pro software
Full evaluation requires the following additional hardware:
• A high-speed 4-CH oscilloscope capable of resolving 5-ps step size for SYSREF delay tuning
• A 2-CH arbitrary function generator or other pulse source capable of outputting complementary LVDS pulses
and DC levels (1.25 V ± 0.2 V, differential, into 100-Ω DC load) for triggering SYSREF, SYNCing the dividers,
and determining SYSREF windowing values
• A phase noise analysis system capable of measuring at up to 18 GHz
2.1.2 Connection Diagram
50Ω
50Ω
50Ω
50Ω
Power Supply
3.3V, 2A
2-CH Arbitrary
Function Generator
1.3V ± 0.2V
High-Quality Signal
Generator
PC with TICSPro &
device profile installed
50Ω
50Ω
Balun
Signal Analyzer
50Ω
50Ω
50Ω
50Ω
4-CH
Oscilloscope
50Ω
50Ω
50Ω
50Ω
TP14
TP16
J14
TP11
TP10
TP1
TP6
TP4 TP9
TP5
TP12
TP7
J29
J28
J40
Figure 2-1. EVM Connection Diagram
www.ti.com Hardware
SNAU288 – DECEMBER 2023
Submit Document Feedback
LMX1906-SP Evaluation Module 3
Copyright © 2023 Texas Instruments Incorporated
Table 2-1. SPI Test Points
Test Point Net
TP1 SDO
TP4 CSB
TP5 SCK
TP6 SDI
TP9 CE
Table 2-2. I2C Testpoints for IO Expander
Test Point Net
TP10 SDA
TP11 SCL
Table 2-3. Supply Voltage Test Points
Test Point Net
TP7 VCC01_23
TP12 VCC_CLK_LOGIC
TP14 VCC_PinM
TP16 VCC_BIAS
Table 2-4. VCC Power Jumpers
Header Net Short Position Configuration
J14 CE
1-2 (EVM default) CE pulled high via 10 kΩ resistor results in LMX1909-SP enabled
2-3 External CE signal from USB2ANY in TICSpro 'pin' tab
J28 VCC_BYPASS or 1st LDO
2-3 (EVM default) Use on-board LDOS
1-2 Direct Supply from J23 (VCCIN) SMA connector
J29 VCC_IN or VCC_BYPASS
2-3 (EVM default) Use on-board LDOS
1-2 Direct Supply from J23 (VCCIN) SMA connector
J40 VCC_IN or 2nd LDO 2-3 (EVM default) Use on-board LDOS
1-2 Direct Supply from J23 (VCCIN) SMA connector
Table 2-5. Pin Control Jumpers (IO Expander Configurable)
Jumper Short position Configuration
SYSREFEN (Acts as CE pin for
entire SYSREF sub-system)
J38-J39 (Pulled HIGH) When SYSREFEN is set to HIGH, the entire SYSREF sub-system is
enabled with register defaults set accordingly. SPI can still be used to
disable.
J37-J38 (Pulled LOW) When SYSREFEN is set to low, the entire SYSREF sub-system is
deactivated and SPI cannot re-enable.
LOGICEN (Acts as CE pin for
LOGICH)
J38-J39 (Pulled HIGH) When LOGICEN is set to HIGH, the entire SYSREF sub-system is
enabled with register defaults set accordingly. SPI can still be used to
disable.
J37-J38 (Pulled LOW) When LOGICEN is set to low, all FPGA/LOGIC circuits and the
SYSREF sub-system are deactivated and SPI cannot re-enable.
Hardware www.ti.com
4LMX1906-SP Evaluation Module SNAU288 – DECEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
Table 2-6. Pin State Headers (IO Expander Configurable)
Header Short Position Configuration
PWRSEL[2:0]
000 Output power configurable via SPI
001 - Lowest output power
Pin Mode (Also controllable via IO expander)⋮
111 - Highest Output Power
CLKx_EN Pulled LOW (GND) J31-J32 Disables corresponding CLKOUTx
Pulled HIGH (VCC) J32-J33 Enables corresponding CLKOUTx
CAL Transition from LOW to HIGH Calibrates the multiplier or Resets the divider
LOW Calibration & Reset controllable via SPI
WARNING
If the user wishes to use IO expander, then make sure that no shorts are present on any of the
header pins. Otherwise, the IO expander or the MCU is damaged.
The onboard TCA9535 IO expander allows the user to change pin states without the need of physical shorts on
the header pin. This allows users to toggle pin modes through the GUI as well. If the user wishes to evaluate the
LMX1906-SP without MCU control (physical pin strapping), then make sure no jumpers are present on any of the
pin state headers.
USB POWER needs to be provided if LDOs utilization is desired. VCCIN can have a 3.3 V supply connected but,
if the USB cable is disconnected, then the board is without power.
Table 2-7. Usage Modes
Usage Configuration
With USB & DUT LDOs
• Short J28, J29 and J40 jumpers to LDO
• Apply 3.3 V to VCCIN
• Apply USB connection
Without USB & DUT LDOs
• Short J28, J29 and J40 jumpers to LDO
• Apply 3.3 V to VCCIN
• Apply 5 V to VBIAS (TP16) - To avoid damage to host pc usb port, do not apply
external source to vbias unless usb is disconnected or r44 has been removed.
With USB & DUT LDOs bypassed
• Short J28, J29 and J40 jumpers to bypass
• Apply 2.5 V to VCCIN
• Apply USB connection
Without USB & DUT LDOs bypassed
• Short J28, J29 and J40 jumpers to LDO
• Apply 2.5 V to VCCIN
Note
SPI reading while using DUT LDOs: 3.3 V supply can prevent SPI read-back from functioning as
intended. Make sure the input voltage to U7 is larger than 0.7 * VCCIN and that output voltage of U7 is
greater than 2.31 V.
www.ti.com Hardware
SNAU288 – DECEMBER 2023
Submit Document Feedback
LMX1906-SP Evaluation Module 5
Copyright © 2023 Texas Instruments Incorporated
2.1.2.1 How to Enable Full SPI Control
Short positions for full SPI control (not using IO expander).
Header Short Position Configuration
PWRSEL[2:0] 000 Output power configurable via SPI.
CLKx_EN Pulled HIGH (VCC) Enables corresponding CLKOUTx, SPI can still disable each output.
MUXSEL[1:0] 000 MUXSEL controlled via SPI.
DIVSEL[2:0] 000 DIVSEL controlled via SPI.
SYSREF_EN Pulled HIGH (VCC) Enables entire SYSREF system which is controlled via SPI.
LOGICEN Pulled HIGH (VCC) Enables entire LOGICLK system which is controllable via SPI.
2.1.3 Power Requirements
Apply 3.3 V to the J23 header. The acceptable supply voltage range is 3.1 V to 3.5 V, and the board can draw
up to 1.3 A during operation, so the resistance of the cable is matter. The on-board LDOs have about 40 mA
ground current for converting 3.3 V to 2.5 V supply. Furthermore, enabling or disabling various system functions
can change the board current by 50 % or more.
2.1.4 Pin Mode Strapping
Mode of Operation Jumper Position Multiplier/Divider Short
Position
Multiplier/Divider Value Short
Position
Multiplier mode Short MUXSEL[1:0] to VCC (J35-
J36)
Short DIVSEL[0] & DIVSEL[2] to
GND & short DIVSEL[1] to VCC
x2 Multiplier value
Short DIVSEL[2] to GND x3 Multiplier value
Short DIVSEL[1:0] to GND &
DIVSEL[2] to VCC
x4 Multiplier Value
Divider mode Short MUXSEL[0] to GND
Short DIVSEL[2:1] to GND Div by 2
Short DIVSEL[0] & DIVSEL[2] to
GND
Div by 3
Short DIVSEL[2] to GND Div by 4
Short DIVSEL[1:0] to GND Div by 5
Short DIVSEL[1] to GND Div by 6
Short DIVSEL[0] to GND Div by 7
DIVSEL [2:0] float Div by 8
Buffer mode Short MUXSEL[1] to GND N/A
Note
1. In multiplier mode, A LOW to HIGH transition on CAL header must be done. This is accomplished
using a short on CAL header pin (J38) to VCC.
2. Only divider values of 2/3/4 are available in pin mode. Divider values of 5 , 6 , 7 & 8 are valid
divider values only when in SPI mode.
Hardware www.ti.com
6LMX1906-SP Evaluation Module SNAU288 – DECEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
2.1.5 Reference Clock
Connect the CLKINP SMA connector to a high-quality signal source such as an SMA100B signal generator. Both
CLKIN inputs are terminated internally with 50 Ω to AC-GND (that is, GND connection is formed by an internal
capacitor), so no external termination is required or recommended. Input can be driven differentially, connect
both CLKINP and CLKINN SMA connectors to a balun or a differential clock source.
The default EVM profile configures the device in buffer mode. Logiclk is on by default with a predefined output
divider value of 128. The input frequency can be modified per the operating range of each functional element if
desired. This EVM setup guide and related plots assume 800-MHz input at CLKIN for buffer mode.
To evaluate SYSREF repeater mode, connect the SYSREF input SMAs to a differential output source such
as an arbitrary function generator. The EVM connections for the SYSREF input are DC-coupled and provide
internal 100-Ω termination with several biasing options. At POR, the EVM automatically applies a weak 1.3-V
common mode bias to the SYSREFREQ pins. However, the default EVM profile configures the SYSREF input
for DC-coupled input. In DC-coupled mode, the common mode bias on the SYSREFREQ pins must be between
1 V and 2 V. The input common mode requirements can be fulfilled with a standard LVDS output buffer.
For evaluating SYNC mode and SYSREF windowing, to have a SYSREFREQ input source capable of
consistently meeting setup and hold requirements for a single cycle of the input clock is critical. This can become
very challenging at higher frequencies where set up and hold requirements can be < 50 ps. Another device
capable of picosecond-precision timed pulses, such as LMX2820 or LMX2594, can be used as a reference input
to both CLKIN and SYSREF for evaluating these features.
2.1.5.1 Output Connections
All CLKOUT connections are AC-coupled at the LMX1906-SP EVM and can be connected directly to RF
instruments with 0VDC requirements; an additional DC block is not required. The unused CLKOUT SMA
connector must be terminated with a 50-Ω load, or a differential connection can be used if a balun with the
best frequency range is available.
Recommended oscilloscope connections include one CLKOUT and one SYSREF output from the same channel,
as well as the one LOGICLK and one LOGISYS output.
Other unused CLKOUT SMA connectors must be terminated with 50-Ω single-ended or 100-Ω differential load,
or alternately must be disabled in software, to minimize unterminated output effects on performance.
2.1.5.2 Header Information
The LMX1906-SP EVM can be operated in either pin mode or SPI mode. Pin mode allows basic configuration
of the LMX1906-SP device without the need of a microcontroller. SPI mode provides full customization of the
LMX1906-SP device. Mode of operation is set via on-board headers J31 to J39 which can also be controlled
via the IO expander, more information on this can be found in Section 2.1.5.7. Other headers are used to select
power supply source and set the CE pin.
2.1.5.3 Default Configuration
The LMX1906-SP EVM silicon default is buffer mode with all outputs enabled with maximum output power. SPI
is disabled in this mode assuming no jumpers are being utilized and neither the IO expander. LOGICLOCK is
also enabled in this mode with a fixed divider value of 128.
www.ti.com Hardware
SNAU288 – DECEMBER 2023
Submit Document Feedback
LMX1906-SP Evaluation Module 7
Copyright © 2023 Texas Instruments Incorporated
2.1.5.4 How to Generate SYSREF
To generate a continuous SYSREF signal proceed with the following steps:
1. Set SRREQ_MODE (R14[2:1] ) = SYSREFREQ (0x1)
2. Set SYSREF_MODE (R17[1:0]) = Generator Mode Continuous (0x1)
Figure 2-2. How to Enable Continuous SYSREF and Set SYSREFREQ
3. Set SYSREFREQ_FORCE (R72[2:1]) = HIGH
Figure 2-3. SYSREFREQ_FORCE
Hardware www.ti.com
8LMX1906-SP Evaluation Module SNAU288 – DECEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
2.1.5.5 Multiplier Mode Example
To set LMX1906-SP to multiplier mode by using SPI, follow the steps below:
Set CLK_MUX (R25[2:0] = Multiplier (0x3).
Figure 2-4. Selecting Multiplier Mode
Set CLK_MULT (R25[5:3]) to appropriate multiplier value for respective CLKIN frequency.
Figure 2-5. Selecting Multiplier Value
www.ti.com Hardware
SNAU288 – DECEMBER 2023
Submit Document Feedback
LMX1906-SP Evaluation Module 9
Copyright © 2023 Texas Instruments Incorporated
Press Calibrate Multiplier button in GUI.
Figure 2-6. Calibrate Multiplier
2.1.5.6 Divider Mode Example
To set LMX1906-SP to divider mode via SPI do the following:
Set CLK_MUX (R25[2:0] = Divider (0x2).
Refer to image above in Section 2.1.5.5.
Set CLK_DIV (R25[5:3]) to appropriate divider value for respective CLKIN frequency.
Figure 2-7. Divider Value
The CLKIN frequency divided by respective divider value at CLKOUTx is now available for viewing.
Hardware www.ti.com
10 LMX1906-SP Evaluation Module SNAU288 – DECEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
Tabla de contenidos
Otros manuales de Placa madre de Texas Instruments
Texas Instruments
Texas Instruments bq51025EVM-649 Manual de usuario
Texas Instruments
Texas Instruments TPD3S716-Q1EVM Manual de usuario
Texas Instruments
Texas Instruments DLP5532HBQ1EVM Manual de usuario
Texas Instruments
Texas Instruments TPS40130EVM-001 Manual de usuario
Texas Instruments
Texas Instruments LMP91300SWIFEVM Manual de usuario
Texas Instruments
Texas Instruments DRV8432EVM Manual de usuario
Texas Instruments
Texas Instruments DS110DF111EVM Manual de usuario
Texas Instruments
Texas Instruments ADS5413EVM Manual de usuario
Texas Instruments
Texas Instruments INA253EVM Manual de usuario
Texas Instruments
Texas Instruments TMAG5328 Manual de usuario
Texas Instruments
Texas Instruments TAS5733LEVM Guía de solución de problemas
Texas Instruments
Texas Instruments TPS53915EVM-PWR587 Manual de usuario
Texas Instruments
Texas Instruments CC1175EM Manual de usuario
Texas Instruments
Texas Instruments UCD3138CC64EVM-030 Manual de usuario
Texas Instruments
Texas Instruments Stellaris LM3S1968 Manual de usuario
Texas Instruments
Texas Instruments REF35 Manual de usuario
Texas Instruments
Texas Instruments AM574 Series Manual de usuario
Texas Instruments
Texas Instruments bq25606 Manual de usuario
Texas Instruments
Texas Instruments DAC7811EVM Manual de usuario
Texas Instruments
Texas Instruments ISO1644DWEVM Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
Biostar
Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación
