Texas Instruments LM3000 Manual de usuario

User’s Guide

LM3000 Buck Controller Evaluation Module User's Guide

Table of Contents

1 Introduction.............................................................................................................................................................................2

2 Powering and Loading Considerations................................................................................................................................ 3

2.1 Quick Setup Procedure...................................................................................................................................................... 3

3 Board Configuration...............................................................................................................................................................4

3.1 External Clock Synchronization......................................................................................................................................... 4

3.2 CLKOUT.............................................................................................................................................................................4

3.3 Tracking..............................................................................................................................................................................4

3.4 Output Voltage Ripple........................................................................................................................................................ 5

4 Typical Performance Waveforms.......................................................................................................................................... 6

5 Evaluation Board Schematic................................................................................................................................................. 7

6 Bill of Materials....................................................................................................................................................................... 8

7 PCB Layout............................................................................................................................................................................10

8 Revision History................................................................................................................................................................... 13

List of Figures

Figure 2-1. Basic Test Setup for LM3000EVAL Board................................................................................................................. 3

Figure 3-1. Synchronization at 3.3-V Output............................................................................................................................... 4

Figure 3-2. Tracking with an External Ramp for 3.3-V Output..................................................................................................... 5

Figure 3-3. Output Voltage Ripple Measurement Setup.............................................................................................................. 5

Figure 4-1. Efficiency of 3.3-V Output at 500 kHz........................................................................................................................6

Figure 4-2. Efficiency of 1.2-V Output at 500 kHz........................................................................................................................6

Figure 4-3. Output Ripple Voltage for 3.3-V Output at 8-A Load................................................................................................. 6

Figure 4-4. Output Ripple Voltage for 1.2-V Output at 15-A Load............................................................................................... 6

Figure 4-5. Output Load Transient from 0 A to 6 A for 3.3-V Output........................................................................................... 6

Figure 4-6. Output Load Transient from 0 A to 10 A for 1.2-V Output......................................................................................... 6

Figure 5-1. Evaluation Board Full Schematic.............................................................................................................................. 7

Figure 7-1. Top Overlay as Viewed from Top.............................................................................................................................10

Figure 7-2. Top Layer as Viewed from Top................................................................................................................................ 10

Figure 7-3. Bottom Overlay as Viewed from Top....................................................................................................................... 11

Figure 7-4. Bottom Layer as Viewed from Top...........................................................................................................................11

Figure 7-5. Internal Layer 1 as Viewed from Top.......................................................................................................................12

Figure 7-6. Internal Layer 2 as Viewed from Top.......................................................................................................................12

List of Tables

Table 6-1. Bill of Materials............................................................................................................................................................8

Trademarks

All trademarks are the property of their respective owners.

www.ti.com Table of Contents

SNVA389B – JULY 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

LM3000 Buck Controller Evaluation Module User's Guide 1

1 Introduction

The LM3000 evaluation board is designed to provide the design engineer with a fully functional power converter-

based solution using the LM3000 dual output emulated current mode controller. This evaluation board provides

two output voltages of 3.3 V and 1.2 V. The 3.3-V output is designed to handle a maximum current of 8 A,

whereas the 1.2-V output has a maximum current capability of 15 A. The switching frequency for the converter

is set at 500 kHz. The gate signals for each output voltage will be 180 degree out of phase from each other. The

printed circuit board consists of four layers of FR4 material with 2-ounce copper on top and bottom layer and

1-ounce copper for internal layers. This user's guide contains the evaluation board schematic, bill of materials

(BOM), and a quick setup procedure. Refer to the LM3000 Dual Synchronous Emulated Current-Mode Controller

data sheet for complete circuit design information.

The performance of the evaluation board is as follows:

Input Range 6 V to 18 V

Output voltage 1 (VO1) 3.3 V

Output current 1 0 A to 8 A

Output voltage 2 (VO2) 1.2 V

Output current 2 0 A to 15 A

Switching frequency 500 kHz

Load regulation 1%

Board size 2.68 × 3.146 × 0.068 inches

Introduction www.ti.com

2LM3000 Buck Controller Evaluation Module User's Guide SNVA389B – JULY 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

2 Powering and Loading Considerations

Read this entire page prior to attempting to power the evaluation board.

2.1 Quick Setup Procedure

1. Set the input power supply current limit to 10 A. Turn off the input power supply. Connect the input power

supply to the VIN terminal. Make sure to connect power supply ground to each GND1 and GND2 terminals

in order to provide a short path for input current to return to the power supply.

2. Connect the load with an 8-A capability on VO1 and 15-A capability on VO2. Connect the positive terminal to

VO1 and VO2 and negative terminal to GND1 and GND2.

3. Connect a secondary power supply to EN1 and EN2 terminals. Set the power supply voltage to 5 V. The

ground return for this power supply should be connected to GND terminal. Since the evaluation board is

configured such that VOUT2 tracks VOUT1, VOUT2 cannot be turned on without turning on VOUT1. Different

configuration can be required in order to turn on VOUT2 independently. This will be discussed later in

Section 3.3.

4. Set VIN to 12 V with no load being applied. Turn on the input power supply followed by the secondary power

supply in order to power up the enable pins. The output voltage should be in regulation with a value of 3.3 V

on VO1 and 1.2 V on VO2.

5. Slowly increase the load in each output into its maximum output current while monitoring the output voltages

in each channel. The output voltages should also be in regulation at each respective maximum output

current.

6. Slowly vary the input voltages from 6 V and 18.5 V. Both output voltages should remain in regulation with a

nominal value of 3.3 V on VO1 and 1.2 V on VO2.

Figure 2-1. Basic Test Setup for LM3000EVAL Board

www.ti.com Powering and Loading Considerations

SNVA389B – JULY 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

LM3000 Buck Controller Evaluation Module User's Guide 3

3 Board Configuration

3.1 External Clock Synchronization

A SYNC terminal has been provided in this evaluation board in order to synchronize the converter to an

external clock or other fixed frequency signal from 200 kHz to 1.5 MHz. Refer to the LM3000 Dual Synchronous

Emulated Current-Mode Controller data sheet for complete information.

Figure 3-1. Synchronization at 3.3-V Output

3.2 CLKOUT

A CLKOUT terminal provides an external clock signal 90 degrees out of phase with the main clock. This clock

signal can be used to synchronize a second LM3000.

3.3 Tracking

The LM3000 evaluation board is configured such that VOUT2 tracks VOUT1, while VOUT1 voltage increases

with a rate determined by the value of C17, the soft-start capacitor for VOUT1 (Condition 1). This configuration

will not allow VOUT2 to be turned on independently without turning on VOUT1. In order to track VOUT1, the

TRK2 pin should be connected to a divider junction between R14 and R15 through R26.

When both outputs are used to track an external source (Condition 2), then R25, R26, and R28 should be left

open and a 10-Ω resistor should be added into R24 and R27.

If no tracking feature is required, both TRK1 and TRK2 should then be tied to VDD in order to soft start each

output voltage based on a soft-start capacitor value (Condition 3). This can be done by keeping R24, R26, and

R27 open while adding a 10-Ω resistor onto R25 and R28.

Please note that the slew rate of track signal should be lower than the soft-start slew rate, which is set by

soft-start capacitor value.

The following are the summary of different tracking configuration on the LM3000EVAL board:

Condition R24 R25 R26 R27 R28

1 Open 10 Ω 10 Ω Open Open

2 10 Ω Open Open 10 Ω Open

3 Open 10 Ω Open Open 10 Ω

Board Configuration www.ti.com

4LM3000 Buck Controller Evaluation Module User's Guide SNVA389B – JULY 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

Figure 3-2. Tracking with an External Ramp for 3.3-V Output

3.4 Output Voltage Ripple

Output voltage ripple measurement should be taken directly across the output capacitor C21 or C22. Care has to

be taken to minimize the loop area between the scope probe tip and the ground lead in order to minimize noise

in the measurement. This can be achieved by removing the spring tip of the probe and ground lead and then

wire a bare wire around the scope probe shaft. The bare wire should be in contact with the probe shaft because

this is the “new” ground lead for the probe. The measurement can be taken by connecting the bare wire onto the

ground side of the capacitor and the probe tip onto the other side of the capacitor. Figure 3-3 shows a diagram of

this measurement technique.

Figure 3-3. Output Voltage Ripple Measurement Setup

www.ti.com Board Configuration

SNVA389B – JULY 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

LM3000 Buck Controller Evaluation Module User's Guide 5

4 Typical Performance Waveforms

Figure 4-1. Efficiency of 3.3-V Output at 500 kHz Figure 4-2. Efficiency of 1.2-V Output at 500 kHz

Figure 4-3. Output Ripple Voltage for 3.3-V Output

at 8-A Load

Figure 4-4. Output Ripple Voltage for 1.2-V Output

at 15-A Load

Figure 4-5. Output Load Transient from 0 A to 6 A

for 3.3-V Output

Figure 4-6. Output Load Transient from 0 A to 10 A

for 1.2-V Output

Typical Performance Waveforms www.ti.com

6LM3000 Buck Controller Evaluation Module User's Guide SNVA389B – JULY 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

5 Evaluation Board Schematic

Figure 5-1. Evaluation Board Full Schematic

www.ti.com Evaluation Board Schematic

SNVA389B – JULY 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

LM3000 Buck Controller Evaluation Module User's Guide 7

6 Bill of Materials

Table 6-1. Bill of Materials

ID Part Number Type Size Parameters Qty Vendor

C1, C2,

C3, C4 GRM31CR6E106KA12L Capacitor, Ceramic 1206 10 µF, 25 V, X5R, 10% 4 Murata

C5 7343-43 Not Used 0

C6,C7,

C8 EEF-UE0G221R Capacitor, Polymer 7343-43 220 µF, 4 V, 12 mΩ 3 Panasonic

C9, C10,

C11, C14 GRM188R61E105KA12D Capacitor, Ceramic 0603 1 µF, 25 V, X5R, 10% 4 Murata

C12, C13,

C30, C31 GRM188R71E104KA01D Capacitor, Ceramic 0603 0.1 µF, 25 V, X7R, 10% 4 Murata

C15 VJ0603Y821KXXA Capacitor, Ceramic 0603 820 pF, 25 V, X7R, 10% 1 Vishay

C16 VJ0603Y272KXXA Capacitor, Ceramic 0603 2.7 nF, 25 V, X7R, 10% 1 Vishay

C17 06035C273KAT2A Capacitor, Ceramic 0603 0.027 µF, 50 V, X7R, 10% 1 AVX

C18 VJ0603Y183KXXA Capacitor, Ceramic 0603 18 nF, 25 V, X7R, 10% 1 Vishay

C19 VJ0603A121JXAA Capacitor, Ceramic 0603 120 pF, 50 V, COG, 5% 1 Vishay

C20, C21 GRM31CR60J226KE19L Capacitor, Ceramic 1206 22 µF, 6.3 V, X5R, 10% 2 Murata

C22 VJ0603A120KXAA Capacitor, Ceramic 0603 12 pF, 50 V, COG, 5% 1 Vishay

C23 06031A270KAT2A Capacitor, Ceramic 0603 27 pF, 100 V, COG, 10% 1 AVX

C24 06035C122KAT2A Capacitor, Electrolytic 0603 1200 pF, 50 V, X7R, 10% 1 AVX

C25,C26 GRM188R71C104KA01D Capacitor, Ceramic 0603 0.1 µF, 16 V, X7R, 10% 2 Murata

C27 06035A121JAT2A Capacitor, Ceramic 0603 120 pF, 50 V, COG, 5% 1 AVX

C28, C29 EEEFK1H151P Capacitor, Aluminum 10x10.2 mm 150 µF, 50 V, 670 mA 2 Panasonic

C32, C33 06031A180KAT2A Capacitor, Ceramic 0603 18 pF, 100 V, COG, 10% 2 AVX

D1, D2 CMSH3-40M Diode, Schottky SMA 3 A, 40 V 2 Central

Semiconductor

D3 CMPD1001A Diode, Switching SOT-23 250 mA, 90 V 1 Central

Semiconductor

Dz1, Dz2 CMHZ4690 Diode, Zener SOD-123 5.6 V, 500 mW 2 Central

Semiconductor

L1 7443551280 Inductor 2.8 µH, 20 A, 3.8 mΩ 1 Wurth

Elektronik

L2 744318120 Inductor 1.2 µH, 22 A, 1.79 mΩ 1 Wurth

Elektronik

Q1, Q3 HAT2168H N-CH MOSFET LF-PAK 30 A, 30 V, 6 mΩ 2 Renesas

Technology

Q2, Q4 RJK0330DPB N-CH MOSFET LF-PAK 45A, 30V, 2.1 mΩ 2 Renesas

Technology

R1 CRCW060313k3FKEA Resistor 0603 13.3 kΩ, 1% 1 Vishay

R2 CRCW06032k94FKEA Resistor 0603 2.94 kΩ, 1% 1 Vishay

R3, R4 CRCW060322k6FKEA Resistor 0603 22.6 kΩ, 1% 2 Vishay

R5 CRCW06033R01FNEA Resistor 0603 3.01 Ω, 1% 1 Vishay

R6 CRCW06032k67FKEA Resistor 0603 2.67 kΩ, 1% 1 Vishay

R7 CRCW06034k64FKEA Resistor 0603 4.64 kΩ, 1% 1 Vishay

R8 CRCW06034M99FKEA Resistor 0603 4.99 MΩ, 1% 1 Vishay

R9 CRCW060315k4FKEA Resistor 0603 15.4 kΩ, 1% 1 Vishay

R10 CRCW060314k3FKEA Resistor 0603 14.3 kΩ, 1% 1 Vishay

R11, R12 CRCW0603100kFKEA Resistor 0603 100 kΩ, 1% 2 Vishay

R13 CRCW060342k2FKEA Resistor 0603 42.2 kΩ, 1% 1 Vishay

R14 CRCW060335k7FKEA Resistor 0603 35.7 kΩ, 1% 1 Vishay

Bill of Materials www.ti.com

8LM3000 Buck Controller Evaluation Module User's Guide SNVA389B – JULY 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

Table 6-1. Bill of Materials (continued)

ID Part Number Type Size Parameters Qty Vendor

R15 CRCW060310k0FKEA Resistor 0603 10 kΩ, 1% 1 Vishay

R16, R17 CRCW06030000Z0EA Resistor 0603 0 Ω 2 Vishay

R18 CRCW060375k0FKEA Resistor 0603 75 kΩ , 1% 1 Vishay

R19, R21 CRCW06031k33FKEA Resistor 0603 1.33 kΩ, 1% 2 Vishay

R20 CRCW0603102kFKEA Resistor 0603 102 kΩ, 1% 1 Vishay

R22, R23 CRCW040210R0FKED Resistor 0402 10 Ω, 1% 2 Vishay

R24, R27,

R28, R29,

R30

Resistor 0603 Not Used

R25, R26 CRC060310R0FKEA Resistor 0603 10 Ω, 1% 2 Vishay

U1 LM3000 Controller 32 Lead

WQFN 1Texas

Instruments

VIN, VO1,

VO2,

GND1,

GND2

1514-2 Turret Terminal 0.090"

diameter 5 Keystone

CLKOUT,

PGOOD2,

TRK2,

EN2,

GND

1573-2 Turret Terminal 0.072"

diameter 5 Keystone

GND,

EN1,

TRK1,

PGOOD1,

SYNC

1573-2 Turret Terminal 0.072"

diameter 5 Keystone

www.ti.com Bill of Materials

SNVA389B – JULY 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

LM3000 Buck Controller Evaluation Module User's Guide 9

7 PCB Layout

Figure 7-1. Top Overlay as Viewed from Top

Figure 7-2. Top Layer as Viewed from Top

PCB Layout www.ti.com

10 LM3000 Buck Controller Evaluation Module User's Guide SNVA389B – JULY 2009 – REVISED FEBRUARY 2022

Submit Document Feedback

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments TAS5722L Manual de usuario

Texas Instruments

Texas Instruments DS320PR810-RSC-EVM Manual de usuario

Texas Instruments

Texas Instruments TPS65300EVM Manual de usuario

Texas Instruments

Texas Instruments DRV8889-Q1EVM Manual de usuario

Texas Instruments

Texas Instruments IWR1443BOOST Manual de usuario

Texas Instruments

Texas Instruments LP5012EVM Manual de usuario

Texas Instruments

Texas Instruments BUF12800 Manual de usuario

Texas Instruments

Texas Instruments ADS7056EVM Manual de usuario

Texas Instruments

Texas Instruments TPA3220EVM Manual de usuario

Texas Instruments

Texas Instruments LMK1C1104DQF Manual de usuario

Texas Instruments

Texas Instruments OPT3001EVM Manual de usuario

Texas Instruments

Texas Instruments TUSB3210 Manual de usuario

Texas Instruments

Texas Instruments TPA3200D1 Manual de usuario

Texas Instruments

Texas Instruments DAC5687 EVM Manual de usuario

Texas Instruments

Texas Instruments TAS5733L Manual de usuario

Texas Instruments

Texas Instruments ADS1146EVM Manual de usuario

Texas Instruments

Texas Instruments TPS2378 Manual de usuario

Texas Instruments

Texas Instruments BQ25170EVM Manual de usuario

Texas Instruments

Texas Instruments AM1810 Manual de usuario

Texas Instruments

Texas Instruments LMR36503RFEVM Manual de usuario

Texas Instruments

Texas Instruments INA185EVM Manual de usuario

Texas Instruments

Texas Instruments INA282-286EVM Manual de usuario

Texas Instruments

Texas Instruments FDC1004EVM Manual de usuario

Texas Instruments

Texas Instruments PCM186xEVM Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario