Texas Instruments TPA3200D1 Manual de usuario

User's GuideSLOU173B – June 2005 – Revised July 2005

TPA3200D1 Audio Power Amplifier Evaluation Module

The TPA3200D1 evaluation module consists of a single 20-W digital input mono audiopower amplifier complete with a small number of external components mounted on acircuit board that can be used to directly drive a speaker with an external I

S audiosource as the input.

Contents1 Introduction .......................................................................................... 22 Operation ............................................................................................ 43 Schematic, PCB Layers and Parts List .......................................................... 94 TPA3200D1 EVM Parts List ..................................................................... 11

List of Figures

1 The TI TPA3200D1 Audio Power Amplifier EVM – Top View ................................ 22 The TI TPA3200D1 Audio Power Amplifier EVM – Bottom View ............................ 33 DEM-DAI/DAC Evaluation Platform .............................................................. 64 TPA3200D1 EVM Schematic ..................................................................... 95 TPA3200D1 EVM – Top Layer .................................................................. 106 TPA3200D1 EVM – Bottom Layer .............................................................. 10

List of Tables

1 TPA3200D1 EVM Specifications ................................................................. 32 Gain Settings ........................................................................................ 53 Digital Audio Receiver Data Format .............................................................. 74 Gain Settings ........................................................................................ 85 TPA3200D1 EVM Parts List ..................................................................... 11

SLOU173B – June 2005 – Revised July 2005 TPA3200D1 Audio Power Amplifier Evaluation Module 1

www.ti.com

1 Introduction

Introduction

This section provides a top and bottom view of the EVM and the EVM board specifications.

Figure 1. The TI TPA3200D1 Audio Power Amplifier EVM – Top View

TPA3200D1 Audio Power Amplifier Evaluation Module2 SLOU173B – June 2005 – Revised July 2005

www.ti.com

Introduction

Figure 2. The TI TPA3200D1 Audio Power Amplifier EVM – Bottom View

Table 1. TPA3200D1 EVM Specifications

TPA3200D1

8 V to 18 VSupply voltage rangeV

4.5 V to 5.5 VI

3 A maxSupply currentI

40 mA maxContinuous output power per channel, PO: 8 Ω,

20 WV

= 18 V, THD+N = 10%R

Minimum load impedance 4 Ω

SLOU173B – June 2005 – Revised July 2005 TPA3200D1 Audio Power Amplifier Evaluation Module 3

www.ti.com

2 Operation

2.1 Quick Start List for Stand-Alone Operation

Operation

To use the TPA3200D1EVM stand-alone or when connecting it into existing circuits or equipment, followthese steps. Connections to the EVM module can be made by inserting stripped wire into the platedthrough holes on the J1, J2 headers and using banana plugs for the other connectors on the PCB.

2.1.1 Power Supply (Step 1)1. Ensure that all external power sources are set to OFF.2. Connect an additional external regulated power supply set to 5 V to the module VDD and GND pins onthe top side of the J2 header.

Note:

This supply should be turned ON before the VCC supply is turned ON.

3. Connect an external regulated power supply adjusted from 8 V–18 V to the module VCC ( J4) and GND(J3) banana jacks taking care to observe marked polarity.

2.1.2 Evaluation Module Preparations (Step 2)

Inputs and Outputs1. Ensure that all connections are made to the I

S inputs (SCLK, BCK, LRCK, DATA, and GND) on theJ1 header.

2. Connect a speaker across OUTP ( J8) and OUTN ( J7)3. Install both gain jumpers GAIN0 ( J5) and GAIN1 ( J6). This sets the gain of the amplifier to the lowestlevel, 12 dB.

Control Inputs1. SHUTDOWN: This terminal is active low. A low on the device terminal (< 0.8 V) shuts down theamplifier; a high (> 2 V) on the device terminal places the amplifier in the active state. Holding downswitch S1 places the amplifier in the SHUTDOWN state. Releasing S1 returns the amplifier to theactive state.2. MUTE: This terminal is active high. A high on this terminal immediately terminates audio playbackthrough the speakers. However, the outputs are still active (they are switching). The outputs are notdisabled like the SHUTDOWN case. S3 on the EVM controls the state of the MUTE terminal. Switchingthe left side of S3 to 1 turns Mute on. Switching S3 to the 0 position turns Mute off.3. FORMAT: This terminal selects between two possible digital data input formats. S2 on the EVMcontrols the data format. Switching the right side of S2 to 0 selects the 16-24 bit, I

S format. Switchingthe right side of S2 to 1 selects the 16-bit right-justified format.4. LSEL/RSEL: A typical digital input data stream consists of 2 channels of data. However, this amplifieris a mono, bridged-tied amplifier. Therefore, it is necessary to select which channel of data is sent tothe mono output. This terminal is used to select between the 2 channels, typically left/right data.Switching the left side of S2 to the RSEL position selects right-channel data. Switching the left side ofS2 to the LSEL position selects left-channel data.5. DEMP: This terminal is used to enable/disable the internal 44.1-kHz de-emphasis filter. S3 on the EVMcontrols the functionality of this terminal. Switching the right side of S3 to the 0 position disables the44.1-kHz de-emphasis. Switching the right side of S3 to the 1 position enables the 44.1-kHzde-emphasis.

6. GAIN0/GAIN1: Together, these terminals control the back-end gain of the amplifier. Jumpers J5 andJ6 control these terminals. The position of these jumpers and resulting gain is shown in Table 2 .

4TPA3200D1 Audio Power Amplifier Evaluation Module SLOU173B – June 2005 – Revised July 2005

www.ti.com

Operation

Table 2. Gain Settings

GAIN1 (J6)

(1)

GAIN0 (J5)

(1)

AMPLIFIER GAIN (dB)

ON ON 12ON OFF 18OFF ON 23.6OFF OFF Reserved

(1)

OFF = Jumper removed; ON = Jumper installed

Control Outputs1. ZERO: This pin is a TTL output for monitoring the state of the digital input. If the data for L-channeland R-channel remains at a 0 level for 1024 sampling periods (or LRCK clock periods), ZERO is set toa logic 1 state. If an input is present, the ZERO output is set to a logic 0. If desired, the output of thisterminal can be inverted with an external transistor and used to place the amplifier in a SHUTDOWNstate when no input is detected (see the operation of the SHUTDOWN terminal in the Control Inputsection). A test point, TP1, is provided to monitor this output.

Power Up1. Verify correct voltage and input polarity, and turn the external power supplies on. The supplies shouldbe sequenced such that the 5-V supply comes up first before the 8-V – 18-V supply is turned on.The EVM should begin operation.2. Adjust the control inputs to the desired settings.3. If no sound is audible, check the state of the MUTE ( S3) switch.4. If the sound is distorted, check the status of the FORMAT ( S2) switch to ensure that the formatselected matches the incoming digital data stream.5. Adjust the amplifier gain by installing/removing the gain jumpers, J5 and J6.6. Switch between the left and right digital data by moving the left side of switch S2 between the twosettings.

SLOU173B – June 2005 – Revised July 2005 TPA3200D1 Audio Power Amplifier Evaluation Module 5

www.ti.com

2.2 Quick Start List for DEM-DAI/DAC Platform Operation

INSTALL EVM

HERE

Operation

To use the TPA3200D1EVM with a DEM-DAI/DAC platform, follow these steps. The DEM-DAI/DACplatform consists of a 96-kHz digital audio receiver that accepts S/PDIF and optical inputs for directinterface to a digital audio source such as an audio precision or component CD/DVD player. This platformcan be used to evaluate the audio performance of the TPA3200D1EVM using a measurement systemsuch as the Audio Precision system. Figure 3 is referenced throughout this section. See theDEM-DAI1742 document (SBAU034 ) for detailed information on the operation of this board.

Figure 3. DEM-DAI/DAC Evaluation Platform

2.2.1 Evaluation Platform Preparations (Step 1)

Setup

1. Install the EVM into the DEM-DAI/DAC platform in the location at the center of the platform. Theheader labeled J1 should be attached to CN101 on the DEM platform. The header labeled J2 shouldbe attached to CN102 on the DEM platform. See Figure 3 for proper alignment.2. Connect a CD/DVD player or audio precision via a single RCA cable from the coaxial (digital) output toCN001 or use an optical cable to connect from the optical (digital) output to U001 on the DEMplatform. See Note 1 in Figure 3 .3. Set switches SW001–SW003 on the DEM platform according to Table 3 . Settings of this switch needto match the FORMAT selection on the TPA3200D1EVM. Other settings of SW001–SW003 are notsupported by the TPA3200D1EVM. See Note 2 in Figure 3 .

6TPA3200D1 Audio Power Amplifier Evaluation Module SLOU173B – June 2005 – Revised July 2005

www.ti.com

Operation

Table 3. Digital Audio Receiver Data Format

SW001 SW002 SW003 Receiver Output Data Format

L H L 16-24 bit I

SH L H 16-bit Right Justified

4. Set switch SW005 to INT (CS8414). See Note 4 in Figure 3 .

Power Supply1. Ensure that all external power sources are set to off2. Connect a 5-V supply to CN054 and CN055 on the DEM-DAI/DAC platform. See Note 3 in theFigure 3 .CN054 should be connected to the positive and CN055 connected to the negative side of thesupply.

3. Connect an external regulated power supply adjusted from 8 V–18 V to the module VCC ( J4) and GND(J3) banana jacks taking care to observe marked polarity. Be careful when inserting the banana plugsto ensure that they are not inserted too far and short out vias on the DEM-DAI/DAC platform below.

2.2.2 Evaluation Module Preparations (Step 2)

Inputs and Outputs1. Ensure that a CD/DVD player or audio precision is connected via a single RCA cable from the coaxial(digital) output to CN001 or use an optical cable to connect from the optical (digital) output to U001 onthe DEM–DAI/DAC platform.2. Connect a speaker across OUTP ( J8) and OUTN ( J7) on the TPA3200D1EVM.3. Install both gain jumpers GAIN0 ( J5) and GAIN1 ( J6) on the TPA3200D1EVM. This sets the gain ofthe amplifier to the lowest level, 12 dB.

Control Inputs1. SHUTDOWN: This terminal is active low. A low on the device terminal (< 0.8 V) shuts down theamplifier; a high (> 2 V) on the device terminal places the amplifier in the active state. Holding downswitch S1 places the amplifier in the SHUTDOWN state. Releasing S1 returns the amplifier to theactive state.2. MUTE: This terminal is active high. A high on this terminal immediately terminates audio playbackthrough the speakers. However, the outputs are still active (they are switching). The outputs are notdisabled like the SHUTDOWN case above. S3 on the EVM controls the state of the MUTE terminal.Switching the left side of S3 to 1 turns Mute on. Switching S3 to the 0 position turns Mute off.3. FORMAT: This terminal selects between two possible digital data input formats. S2 on the EVMcontrols the data format. Switching the right side of S2 to 0 selects the 16–24 bit, I

S format. Switchingthe right side of S2 to 1 selects the 16-bit right-justified format. Switches SW001–SW003 should be seton the DEM platform to match the settings on the EVM.4. LSEL/RSEL: A typical digital input data stream consists of 2 channels of data. However, this amplifieris a mono, bridged-tied amplifier. Therefore, it is necessary to select which channel of data is sent tothe mono output. This terminal is used to select between the 2 channels, typically left/right data.Switching the left side of S2 to the RSEL position selects right-channel data. Switching the left side ofS2 to the LSEL position selects left-channel data.5. DEMP: This terminal is used to enable/disable the internal 44.1-kHz de-emphasis filter. S3 on the EVMcontrols the functionality of this terminal. Switching the right side of S3 to the 0 position disables the44.1-kHz de-emphasis. Switching the right side of S3 to the 1 position enables the 44.1-kHzde-emphasis.

6. GAIN0/GAIN1: Together, these terminals control the back-end gain of the amplifier. Jumpers J5 andJ6 control these terminals. The position of these jumpers and resulting gain is shown in Table 4 .

SLOU173B – June 2005 – Revised July 2005 TPA3200D1 Audio Power Amplifier Evaluation Module 7

www.ti.com

Operation

Table 4. Gain Settings

GAIN1 (J6)

(1)

GAIN0 (J5)

(1)

AMPLIFIER GAIN (dB)

ON ON 12ON OFF 18OFF ON 23.6OFF OFF Reserved

(1)

OFF = Jumper removed; ON = Jumper installed

Power Up1. Verify correct voltage and input polarity and turn the external power supplies on. The supplies shouldbe sequenced such that the 5-V supply comes up first before the 8-V – 18-V supply is turned on.The EVM should begin operation.2. Adjust the control inputs to the desired settings.3. If no sound is audible, check the state of the MUTE ( S3) switch.4. If the sound is distorted, check the status of the FORMAT ( S2) switch to ensure the format selectedmatches the incoming digital data stream selected by SW001–SW003 on the DEM-DAI/DAC platform.5. Adjust the amplifier gain by installing/removing the gain jumpers, J5 and J6.6. Switch between the LEFT and RIGHT digital data by moving the left side of switch S2 between the twosettings.

TPA3200D1 Audio Power Amplifier Evaluation Module8 SLOU173B – June 2005 – Revised July 2005

www.ti.com

3 Schematic, PCB Layers and Parts List

3.1 TPA3200D1 EVM Schematic

LRCK

DGND

BCK

GAIN0

VCOM

DATA

FORMAT

SCLK

GAIN1

LR_SEL

VDD

DGND

VDD

SHUTDOWN

PGND

VCLAMP

BSN

OUTN

PGND

PVCC

COSC

PGND

AGND

BSP

OUTP

ROSC

PVCC

AGND

MUTE

DGND

DEMP

DGND

FLT1

ZERO

FLT2

VCC

VREF

BYPASS

0.1 Fm

10 Fm

220 pF

J1-17

J1-19

J1-18

J1-5, 6,

J2-3, 4,

12, 13

16, 20

GND

J2-1, 2,

VDD

OUTN

OUTP

GND

VCC

S2-A

120 kW

120

120 kW

C14

1 Fm

0.22 Fm0.22 Fm

22 Fm

51 R

C10

C13

D1 D2

1 nF

C12

1 nF

L2 L1

Ferrite Bead Ferrite Bead

VCC

51 R

R1 120 kW

1 Fm

C15

22 nF

TP1

C11

10 Fm

J1-15

J2-1, 2

VDD

S2-B

S3-A

S3-B

Schematic, PCB Layers and Parts List

This section contains the EVM schematic, board layout, and bill of materials.

Figure 4. TPA3200D1 EVM Schematic

SLOU173B – June 2005 – Revised July 2005 TPA3200D1 Audio Power Amplifier Evaluation Module 9

www.ti.com

3.2 TPA3200D1 EVM PCB Layers

Schematic, PCB Layers and Parts List

Figure 5. TPA3200D1 EVM – Top Layer

Figure 6. TPA3200D1 EVM – Bottom Layer

TPA3200D1 Audio Power Amplifier Evaluation Module10 SLOU173B – June 2005 – Revised July 2005

Otros manuales para TPA3200D1

Tabla de contenidos

Otros manuales de Placa madre de Texas Instruments

Texas Instruments

Texas Instruments REF35EVM Manual de usuario

Texas Instruments

Texas Instruments ADC16DX370EVM Manual de usuario

Texas Instruments

Texas Instruments TMDS1204EVM Manual de usuario

Texas Instruments

Texas Instruments XTR300EVM Manual de usuario

Texas Instruments

Texas Instruments LMK5B33216EVM Manual de usuario

Texas Instruments

Texas Instruments RF430RL15 H Series Manual de usuario

Texas Instruments

Texas Instruments TPS25831-Q1 Manual de usuario

Texas Instruments

Texas Instruments TPS65980EVM Manual de usuario

Texas Instruments

Texas Instruments Stellaris LM3S1968 Manual de usuario

Texas Instruments

Texas Instruments DS90UB95x-Q1 Manual de usuario

Texas Instruments

Texas Instruments LM75AEB Manual de usuario

Texas Instruments

Texas Instruments TMAG5124EVM Manual de usuario

Texas Instruments

Texas Instruments DS90UB96X-Q1EVM Manual de usuario

Texas Instruments

Texas Instruments TLV1544EVM Manual de usuario

Texas Instruments

Texas Instruments TRF4903 Manual de usuario

Texas Instruments

Texas Instruments BQ75614-Q1 Manual de usuario

Texas Instruments

Texas Instruments TPS7A52EVM-031 Manual de usuario

Texas Instruments

Texas Instruments TPD1E0B04 Manual de usuario

Texas Instruments

Texas Instruments TPS3847085EVM-577 Manual de usuario

Texas Instruments

Texas Instruments RF430F5978EVM Manual de usuario

Texas Instruments

Texas Instruments BQ25175EVM Manual de usuario

Texas Instruments

Texas Instruments DRV8316 EVM Series Manual de usuario

Texas Instruments

Texas Instruments TPS61054EVM-273 Manual de usuario

Texas Instruments

Texas Instruments TPS56121 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario