Teuco 122W Manual de usuario

2200

720

100

1000

850

650

1010

820

380

810

2200

380

720

100

820

650

1010

1000

810

850

1800

C- Hot water connection for 1

/2"tap fittings

F- Cold water connection for tap fittings 1/2"

O- Connection for drainage pipe recessed in floor 11

/2"

CA - Electrical connection for sauna IPX4

(box with cable press PG 13.5)

N.B. Installation must take place once floors and

walls are completed.

The room in which the sauna is to be installed

should be at least 230 cm for the model that can be

inspected at this height).

Siphon

Net

Weight

Kg.

123 155 2,24 6 0.5 ÷5

bar 1/2"

Delivery

Weight

Kg.

Delivery

Volume

ART.122W - 122R

Vertical

Jets

Back

jets

Foot

jets

9 ÷16

Capacity

l/min

2 ÷5

bar

Pressure

Min. Max Pressure

Min. Max Supply

11/2"

Drain

Conn.

HYDRAULIC CHARACTERISTICS ELECTRICAL

CHARACTERISTICS

(1)

Multifunctions Sauna

(1) - Before connecting the appliance, make sure that the voltage indicated on the rating plate is the same as that of the electric mains.

The information and characteristics shown do not bind Teuco Guzzini Spa who reserves the right to make any modifications it retains necessary without any prior warning or notice of replacement.

Measurements in mm.

The electrical installation must comply with the safety regulations for bathroom installation, as

described in the enclosed user’s manual.

Left-side Model

Right-side Model

Central

Showerh.

12MEX18

2NEX18

Art.

1,9 ÷ 2,3

Min. Max

Sauna and Multifunctions

PRE-INSTALLATION CARD ART. 122W - 122R (mm 1010 x 810)

ASSEMBLING THE CABIN GB

570

2050

FIXING THE UNIT TO THE

WALL

Drill the appropriate hole for fixing

the unit to the wall using the

measurements indicated in the

diagram and then fasten the

bracket (P) with the appropriate

screw and fischer.

INSTALLATION

ON THE RIGHT INSTALLATION

ON THE LEFT

2POSITIONING THE SHOWER

BASE

Place the bathtub in the corner of

the bathroom and make sure it is

on a level by using the appropriate

adjustable feet.

Prepare the drain connection using

the trap supplied with the hose for

the drain (position it as indicated

in the diagram).

N.B.: The unit must be installed af-

ter the floor and walls have been fi-

nished.

All screws and accessories which

are necessary for installation are

in the appropriate box

Bag (A) with screws for

steps 1 - 3 - 3a - 3b

ASSEMBLING THE CABIN

M5X20

Ø5

4,2x60

Ø5

C2 M

M3x8

Ø4

4,2x60

Ø5

M5X20

Ø5

Fit the rubber doorstop (M) onto

the panel (B) and fasten it with the

screw and washer (C3).

Remove the screw from the end

piece on the bottom track.

Apply silicone to the end of the

track at the point indicated.

Position the panel (B) on the

shower base and fasten it to the

track with the screw and washer re-

moved earlier (C).

Insert the screws and washers (C1)

into the frame of the back shower

panel and into the shower base

without tightening them.

ASSEMBLING THE BACK

PANELS

Place drain cover on the drain in

the shower base.

Move the shower base away from

the corner in order to proceed with

the subsequent assembly steps.

Remove the screws (C1) from the

end of the bottom track.

Apply silicone to the end of the

track as shown in the diagram.

Place the back panel (A) with the

seat onto the shower base and in-

sert the support onto the end of the

bottom track.

Fasten the panel (A) to the track

with the screw and washer (C1) re-

moved earlier.

Insert the screw and washer (C1)

into the back panel to fasten it to

the shower base.

Bag (C) - plastic accessories

ASSEMBLING THE CABIN GB

Ø5

M5x25

Ø5

C1 C1

INSTALLING THE SIDE

PANEL

Apply silicone to the groove in the

track in the area corresponding to

the position of the side panel and

end cap.

Slide the side panel (B1) into the

bottom track.

Position the threaded pins on the

support for the side panel (B1) so

that they match up with the holes

on the back panel (B); if necessary,

use a 2.5 Allen wrench.

Check that the seal (!) fits properly

along the entire length of the side

panel (B1) support.

Fasten the side panel (B1) to the

back panel (B) by tightening the

nuts with washers (C).

3b Fasten the panels (A) and (B) to-

gether with the screws, nuts and

washers (C3).

Tighten the screws (C1) which have

already been inserted into the

shower base.

Consult the attached manual for in-

structions on how to install the

taps.

4Bag (A) - screws for phases 4-5

ASSEMBLING THE CABIN

4,2x60

Ø5

4,2x60

Ø5

APPLYING SILICONE

Apply a NEUTRAL (NON ACETIC)

silicone so as to prevent water from

leaking between the back panel

and the bathtub.

INSTALLING THE TOP

TRACK

Remove the screws from the ends

of the top track.

Insert the track onto the ends of

the supports and fasten it to the

back panels using the screws and

washers (C) that were removed ear-

lier.

Tighten the screws on the ends of

the side panel support (B1), as in-

dicated in the diagram.

ASSEMBLING THE CABIN GB

M5x45

M4x30

MOUNTING THE DOOR

Assemble the handles onto the

door supports, using the screws

provided (C3).

Insert the track cover (V) and the

finish end pieces (Y) into the top

and bottom tracks.

Turn the nut (D) until it is flush

with the top of the (C) screw.

Mount the door, hooking the

wheels (P) with the spring support

onto the lower track

Lift the door up so that the top

wheels (N) slide into the track.

MOUNTING THE TWO-CLIMATE

SAUNA DOME UNTO THE

SHOWER CABIN

Place the adhesive steam seal onto

the top edge of the back panels.

Insert the screw (C) into the

appropriate hole on the back shower

panel.

Position the sauna onto the shower

cabin, making sure not to damage

the water and electrical hoses atta-

ched to it.

To center the sauna, insert the front

flap into the groove on the top track,

making sure that the seal (G) is turned

toward the inside of the shower cabin.

ONLY FOR ARTICLES

122 STEAM - 122 EASY

CONNECTIONS FOR VARIOUS MODELS

A6- Connection for hose 3 (drainage).

N.B.: Hoses 1 and 2 for the

decalcification system must always be

filled with water. Therefore, this

system must not be emptied during

installation.

CA-Electrical connection for the

IPX4 sauna (box with PG13.5

cable clamp ).

CA P

521

Art. 122R (EASY)- Easy Multifunction Shower Box with 2 Climates Steam Sauna

Once the plugs (D) have been

removed, they should not be used

again.

C - Hot water connection.

Use a 90 cm flexible stainless

steel hose.

F - Cold water connection.

Use a 90 cm flexible stainless

steel hose.

A1- Connection for hoses 1 and 2 for

the sauna unit and for hose 5 for

the shower head with nebulizer.

A2-Connection for hose 8 for the

vertical massage and for hose 10

for the back massage.

A3- Cleaning of the taps with filter.

A4-Connection between the

electrical cable coming from the

dome and cable coming from the

power unit.

A5- Connection for hose 4 (boiler).

Blue

Yellow-Green

Brown

CONNECTIONS FOR VARIOUS MODELS GB

FAST ON INSULATED

EMERGENCY TAP (ART. 122 EASY)

SHOWER SUPPORT ROD

SHUT-OFF VALVE FOR THERMOSTATIC MIXER

MIXER OR THERMOSTATIC MIXER

DIVERTER

FRAME FOR BACK PANEL WITH TAPS

FRAME FOR BACK PANEL WITH SEAT

EQUIPOTENTIAL EARTHING

CONNECTION

Connect the metal parts of the ca-

bin with the yellow wire as indica-

ted in the diagram.

There is a terminal at point (7) for

the equipotential connection of the

other grounds present in the room.

N.B.:If one of the components indi-

cated in the diagram is not present

on the model purchased, insulate

the corresponding “fast on”.

ONLY FOR ARTICLES

122 STEAM - 122 EASY

ASSEMBLING THE CABIN

FITTING THE INSPECTION

DOOR

Position the shower cabin against

the wall.

Close the door and make sure that

the magnetic seals are aligned along

the entire length of the door.

In the event that the seals do not

come together - as in case (A) or

case (B) - adjust the top slide

assembly indicated by the arrow.

- Lift the door, grasping it by the

supports.

- Tighten the screw (D) until the

magnetic seals are aligned.

N.B. After adjusting the slide

assembly, lock the nuts (D) in place,

inserting the covers (K) with the

inner wings facing outwards.

USING THE SHOWER FOR

THE FIRST TIME

Once all of the connections are

made and before fastening the ca-

bin to the wall, remove all of the

adhesive tags.

Run the regeneration and a sauna

cycle, following the instructions

contained in the attached user’s

manual.

Make sure that there are no water

leaks in the connections made and

that everything operates normally.

If there is no power to the sauna

system after the electrical connec-

tion has been made to the mains,

press the red button on the power

unit box.

If the control panel displays an er-

ror message (all the leds will blink)

the first time the sauna system is

turned on, remove the grate and

press the button for resetting the

thermostat, indicated with the ar-

row.

ONLY FOR ARTICLES

122 STEAM - 122 EASY

ASSEMBLING THE CABIN GB

4,2x38

Ø5

M5x16

Ø5-M5

Ø5

M5x20

M5-Ø5

M5x20

M5-Ø5

Bag (B) - screws for step 13

FIXING THE SHOWER TO

THE WALL

Position the shower cabin against

the wall.

To fasten the unit, lift the sauna

dome and place a spacer between

the track and the dome itself.

Insert the bracket (T) into the plate

(P), which has already fastened to

the wall, and onto the screw (C) on

the shower cabin.

Tighten the bracket (T) with the

nut and washer (C2).

Move the shower cabin next to the

wall, position the bracket (T1) on

the frame, drill a hole in the wall,

insert the screw with the fischer

and fasten the bracket (T1) to the

frame, tightening the screw with

the washer (C1).

Remove the spacer and center the

dome on the shower cabin (see fig.

8).

Open the top of the dome by

removing the screws (C3); fasten

the bottom of the dome with the

nut and washer (C2) onto the screw

Repeat this last procedure on the

other side with the other nut and

washer (C4).

Close the top of the dome and

fasten in place with the screws

which were removed earlier.

Fit the side panel by sliding it

down from the top so as to hook it

onto the support brackets on the

frame.

Fix the side panels by tightening

the towel-knob with the screws and

washers (C3); insert the trim.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Jacuzzi de Teuco

Teuco

Teuco 620HU Manual de usuario

Teuco

Teuco 2WSC18 Manual de usuario

Teuco

Teuco 615 Manual de usuario

Teuco

Teuco 640 Manual de usuario

Teuco

Teuco SEASIDE 641 HA Manual de usuario

Teuco

Teuco 630HU Manual de usuario

Teuco

Teuco C30F Manual de usuario

Teuco

Teuco 611 Manual de usuario

Teuco

Teuco 620 Manual de usuario

Teuco

Teuco C22F Manual de usuario

Teuco

Teuco 629 Manual de usuario

Teuco

Teuco CHEERS CH3 Manual de usuario

Teuco

Teuco 382 Manual de usuario

Manuales populares de Jacuzzi de otras marcas

Bestway

Bestway Lay-Z-Spa 54189 Manual de usuario

Jacuzzi

Jacuzzi ARGA ARG101C0110 Manual de lista de piezas

Morphy Richards

Morphy Richards Essentials PC4006 Manual de usuario

Softub

Softub PRESTIGE Manual de usuario

JNJ SPAS

JNJ SPAS SPA-318 Manual de instalación

KIRAMI

KIRAMI Comfort Family Manual de usuario

QCA Spa

QCA Spa VS501 PAK (VL260 TOPSIDE) Manual de usuario

HoMedics

HoMedics FB-655HJ-GB Manual de usuario

Everyday Hot Tubs

Everyday Hot Tubs 530 Manual de usuario

anko

anko SS-601A Manual de usuario

Jacuzzi

Jacuzzi Duetta 6042 Manual de usuario

Pooli

Pooli OS030979B Manual de usuario

Jacuzzi

Jacuzzi alimia Manual de usuario

ab Solares Smart Spa Manual de usuario

CalderaSpas

CalderaSpas CalderaSpas Utopia Series Manual de usuario

Outsunny

Outsunny 848-047V70 Manual de usuario

Aquatic

Aquatic INFINITY 1 Manual de usuario

Master Spas

Master Spas MP Force Manual de usuario