TESTO 511 Manual de usuario

Otros manuales para 511

4

Tabla de contenidos

Otros manuales de Instrumento de medición de TESTO

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Instruction manual

testo 511

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

11

Short manual testo 511

Protection cap: Park position

Absolute pressure sensor nipple

connection

Display

Control keys

Battery compartment, holding

magnets (on rear)

Basic settings

Instrument off >press and hold 2s > select with ( ),

confirm with ( ):

Unit of height above mean sea level: m, ft > Value of height above mean sea level

(Altitude) > Unit of pressure: hPa, mbar, Pa, mmH2O, mmHg, psi, inH2O, inHG, >

Auto off function: OFF, ON

Switching the instrument on

Press .

Switching the display light on(for 10s)

Instrument on > press

Select display size

Instrument on > select with :

Absolute pressure, barom (barometric pressure), Altitude (height above mean sea

level)

Select display mode

Instrument on > select with :

Current reading > Max: Maximum values > Min: Minimum values

Switching the instrument off:

Instrument on >press and hold 2s.

de

enfresitptsvnl????

Short manual testo 511

12

Safety and the environment

About this document

iPlease read this documentation through carefully and

familiarise yourself with the product before putting it to use.

Keep this document to hand so that you can refer to it when

necessary. Hand this documentation on to any subsequent

users of the product.

iPay particular attention to information emphasised by the

following symbols:

Important.

Avoid personal injury/damage to equipment

iOnly operate the measuring instrument properly, for its

intended purpose and within the parameters specified in the

technical data. Do not use force.

iNever store the product together with solvents, acids or other

aggressive substances.

iOnly carry out the maintenance and repair work that is

described in the documentation. Follow the prescribed steps

when doing so. Use only OEM spare parts from Testo.

Strong magnets. Damage to other instruments!

iKeep a safe distance from products which could be damaged

by magnetism (e.g. monitors, computers, pacemakers, credit

cards).

Protecting the environment

iTake faulty rechargeable batteries as well as spent batteries to

the collection points provided for them.

iSend the product back to Testo at the end of its useful life. We

will ensure that it is disposed of in an environmentally friendly

manner.

Safety and the enviroment

13

Specifications

Functions and use

The testo 511 is an absolute pressure measuring instrument. It is

normally used to measure absolute pressure, e.g. for pressure

compensation in velocity measurement in ducts, laboratories and

production processes. Further measurement parameters are

barometric (surface) pressure (= pressure at sea level) and altitude

above sea level.

Technical data

Measurement data

· Sensor:

Absolute pressure sensor

· Parameters (absolute/barometric):

Pa, hPa, mbar, mmH2O, mmHg, inHG,

inH2O, psi

· Measuring ranges:

300...1,200 hPa, 120.4...481.8 inH2O

· Resolutions:

0.1 hPa, 0.01 inH2O

· Accuracies

(Nominal temperature 22 °C, ±1 Digit):

±3 hPa, ±1.2 inH2O

·Measuring rate:

0.5 s

Further instrument data

· Protection class: IP40

· Ambient conditions:

0...50 °C, 32...122 °F

· Storage/transport conditions:

-40...70 °C, -40...158 °F

· Voltage supply:

2x 1.5 V type AAA

· Battery life:

200 h (without display light)

·Dimensions:

119x46x25mm / 4.7x1.8x1.0 in (inc.

protection cap)

· Weight: 90g / 3.2 oz (inc. batteries and

protection cap)

Directives, standards and tests

· EC Directive: 2004/108/EEC

Warranty

· Duration: 2 years

· Warranty conditions: see guarantee

card

de

enfresitptsvnl????

Specifications

Test Equipment Depot - 800.517.8431

99 Washington Street,Melrose, MA 02176

TestEquipmentDepot.com

14

Product description

At a glance

Protection cap: Park position

Absolute pressure sensor nipple

connection

Display

Control keys

Battery compartment, holding

magnets (on rear)

First steps

²Inserting batteries:

1To open the battery compartment, push the battery cover

down.

2Insert batteries (2x 1.5 V type AAA). Observe the polarity!

3To close the battery compartment, push the battery cover

back on.

²Basic settings (configuration mode):

Adjustable functions

· Unit of height above mean sea level: m, ft

· Value of height above mean sea level (Altitude): Set flashing figure with ,

change to next figure with .

· Unit of pressure: hPa, mbar, Pa, mmH2O, mmHg, psi, inH2O, inHG,

· Auto off function: OFF, ON (instrument switches off automatically if no key is

pressed for 10 minutes)

1When switching the instrument on, press and hold until

and appear on the display (configuration mode).

- The adjustable function is displayed. The current setting

flashes.

2Press ( ) several times until the desired setting flashes.

Product description

15

3Press ( ) to confirm the input.

4Repeat steps 2and 3for all functions.

- The instrument changes to measuring mode.

Using the product

For measuring barometric (surface) pressure barom (= pressure

at sea level), the following must be observed:

· the altitude of the measurement site above sea level must be known,

and be set in the instrument, see chapter ‘First steps’, section ‘Basic

settings (configuration mode)’.

· The barometric pressure displayed is only correct for the altitude set,

for a change of altitude, the altitude above sea level must be reset.

For measuring barometric Altitude (= altitude relating to a fixed

level), the following must be observed:

· The altitude above sea level at the starting point of the measurement

(= Reference altitude) must be known and be set in the instrument,

see chapter ‘First steps’, section ‘Basic settings (configuration

mode)’. When entering the reference altitude, the current absolute

pressure is also stored as a reference pressure.

· When carrying out the measurement at the destination, the weather

conditions must be the same as when entering the reference altitude.

If the weather has changed (= change of absolute pressure), a new

reference value must be entered.

²Switching the instrument on:

iPress .

- Measuring mode is opened.

²Switching the display light on:

The instrument is switched on.

iPress .

- The display light goes out automatically if no key is

pressed for 10 seconds.

de

enfresitptsvnl????

Use the product

16

²Changing the parameter:

The parameter can be changed.

Adjustable parameters

· Absolute pressure

·barom (barometric pressure)

·Altitude (height above mean sea level)

iPress several times until the desired parameter appears.

²Changing the display view:

Adjustable views

· Current reading

·Max: Maximum values since the instrument was last switched on or last reset.

·Min: Minimum values since the instrument was last switched on or last reset.

iPress several times until the desired view appears.

²Resetting Max/Min values:

1Press several times until the desired view appears.

2Press and hold until ---- appears.

3Repeat steps 1and 2for all values that are to be reset.

²Switching the instrument off:

iPress and hold until the display goes out.

Maintaining the product

±Changing batteries:

1To open the battery compartment, push the battery cover

down.

2Remove used batteries and insert new batteries

(2x 1.5 V type AAA). Observe the polarity!

3To close the battery compartment, push the battery cover

back on.

±Cleaning the housing:

iClean the housing with a moist cloth (soap suds) if it is dirty.

Do not use aggressive cleaning agents or solvents!

Maintaining the product

Tips and assistance 17

Tips and assistance

Questions and answers

Question Possible causes/solutions

Hi or Lo · Readings outside the measuring range (too high, too

low): Keep to the permitted measuring range.

· Residual capacity <10 min: Change batteries.

de

enfresitptsvnl????

Notes18

0973.5111/03/Sh/dr/10.04.2008

Test Equipment Depot - 800.517.8431

99 Washington Street,Melrose, MA 02176

TestEquipmentDepot.com