TESTO 327 Manual de usuario

Quick Start Guide

Model 327

Follow these basic steps outlined in this Quick Start Guide

to get you up and running with your new meter quickly and easily

Before using completely charge the battery

(for how long)

- attach power supply to analyzer

plug the power cord into wall socket

PTest screen displayed

(all segments are lit : 3s)

PInitial screen displayed

(Serial number, firmware version,

instrument model number, date, time

and country code : 5s)

FOrange hot keys can be used to:

- change fuel (Fuel)

- enter flue gas measuring mode

(Flue g)

- enter diagnostics mode

(Diagnost)

PMeasuring Mode Displayed (fig. 2)

Change measurement mode (press )

(See Fig xx Measuring Mode menu

items)

FOrange hot keys can be used to

- change fuel (Fuel) (some modes)

- select measuring mode (OK)

Measuring

Flue gas

Fuel OK

Serial Number

Firmware Version

Sec.

Zero

°F

Tamb

MM/DD

YYY

Date

T I : M E

(EXAMPLE: Flue Gas Measuring Mode)

Note: Items in display are user

configurable and may not match this example

FPress OK hot key to enter mode

(Note: press esc to exit mode)

CAUTION:

30 SEC. COUNTDOWN IS A NULL

CALIBRATION. ENTER THIS MODE IN

CLEAN AIR ONLY

fig 3

7 5 . 7

29

FChange fuel (press / )

FOrange hot keys can be used to:

- change fuel (Fuel)

- change date and time (Date)

Reminder: verify date and time

fig 2.

PInitial flue gas measuring

mode screen displayed (fig. 4)

Note: This display will only appear if a Null

Calibration has NOT been performed.

Reentering Flue Gas mode after Null Calibration

will bypass this display.

Reminder: Dashes (----) appear when that

data field is empty

- Data has not been saved

- Calculation is out of limits

- Probe/sensor has not been

installed

Flue gas

Nat gas

°F

Tstack

%

CO2

%

EFF

%

ExAir

0.0

7 5 . 7

_________

_________

fig 4

FChange fuel (press / )

FOrange hot keys can be used to:

- enter measuring mode (OK)

PFlue Gas Measuring Mode Screen

Displayed (fig. 5)

Flue gas

Nat gas

°F

Tstack

%

CO2

%

EFF

%

ExAir

8 0 3 . 0

7 5 . 7

_________

_________

FScroll though line items

(press / )

FOrange hot keys can be used to:

- change fuel (Fuel)

- Start measuring flue gasses

(Start)

Reminder:

Probe must be inserted into

stack to take stack measurements

fig 5.

PFlue Gas Null Calibration Screen

Displayed (fig. 3)

Step 1 - Charge battery.

Step 2-

Attach Probe

to Instrument

see fig 1.

fig 1.

Step 3- Turn Instrument ON

Step 4 - Select Measuring Mode

see fig 5.

Fuel

OK

Fuel Start

j

k

l

m

n

o

p

Product

Description:

j- IR interface,

ON/OFF switch

k- Display

l- Control keys

m- Power supply,

probe connec

tions, gas

outlet

n- condensate

trap

o- battery, cells

compartment

p- magnetic back

testo, Inc. 35 Ironia Rd., Flanders, NJ

07836, 800-227-0729, fax 973-252-1729,

www.testo.us. e-mail: [email protected]

Please read, undersand and follow the directions, pre-cautions

and warnings in the product instruction manual.

CAUTION:

Water trap level should be monitored and

emptied to avoid damage that is possible

when moisture is pumped into analyzer

PFlue Gas Measuring Mode Displayed

(fig. 6)

Flue gas

Nat gas

°F

Tstack

%

CO2

%

EFF

%

ExAir

8 0 3 . 0

7 5 . 7

1 . 1 4

8 8 . 2

FScroll though line items

(press / )

FOrange hot keys can be used to:

- change fuel (Fuel)

- start measuring flue gasses

(Start)

Reminder:

Probe must be inserted into

stack to take stack measurements

FOrange hot keys can be used to:

- print real time measurements

- lock in measurements (Stop)

Reminder:

This assumes you pressed the START

button on the previous screen

PFlue Gas Measuring Mode Displayed

(fig. 7)

Flue gas

Nat gas

°F

Tstack

%

CO2

%

EFF

%

ExAir

8 0 3 . 0

7 5 . 7

1 . 1 4

8 8 . 2

fig 6

fig 7

FOrange hot keys can be used to:

- print locked-in measurements

(Print)

- Start a new test (Start)

Reminder:

This assumes you pressed the STOP

button on the previous screen

CAUTION:

Pressing Start again will write over

locked-in data from previous real-time

flue gas measurements.

Items NOT to be written over are:

Draft

CO-AirFree

- When stored independent

measurement

Smoke/Oil

Diff prs

Delta Temp

Ambient CO

Analyzer will enter a purge mode from 1-90 seconds based on last O2 measurement

taken then cycle off

CAUTION:

All locked-in and saved date will be deleted

AEmpty water trap daily (minimum) or when it appears to be full (see figure 8)

A

Disconnect probe from the instrument during storage of the analyzer wile not in use

AReplace the particle filter when visibly dirty (see fig. 9)

fig 8

Step 5 - Insert gas-sampling

probe into stack Step 6 - Print locked-in data Step 7 - Turn OFF instrument

Step 8 - Care for your analyzer

fig 9

Fuel Start

Print Start

August, 2007

Otros manuales para 327

2

Otros manuales de Instrumento de medición de TESTO

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario