Tenda S105 Manual de usuario

is the registered trademark of Shenzhen Tenda

Technology Co., Ltd. All the products and product names mentioned

herein are the trademarks or registered trademarks of their respective

holders. Copyright of the whole product as integration, including its

accessories and software, belongs to Shenzhen Tenda Technology Co.,

Ltd. Without the permission of Shenzhen Tenda Technology Co., Ltd, any

individual or party is not allowed to copy, plagiarize, imitate or translate it

into other languages.

All the photos and product specifications mentioned in this guide are for

references only. As the upgrade of software and hardware, there will be

changes. And if there are changes, Tenda is not responsible for informing

in advance. If you want to know more about our product information,

please visit our website at www.tendacn.com

Contents

1. Introduction-----------------------------------------------------------------------------2

1.1 Switch Features -------------------------------------------------------------2

1.2 Package Contents-----------------------------------------------------------3

1.3 Front Panel and Rear Panel Specifications-------------------------3

1.4 LED Indicator Specifications--------------------------------------------3

2. Installation-------------------------------------------------------------------------------4

2.1 Before Connecting to the Network ------------------------------------4

2.2 Connecting to End Nodes------------------------------------------------4

2.3 Switch to Router or Switch ----------------------------------------------5

3. Product Specification----------------------------------------------------------------6

1. Introduction

S105/S108 Ethernet Switch, a mini desktop switch, is designed for SOHO,

student dormitory and small enterprise users. It has 5/8 10/100Mbps

Auto-negotiation Ethernet ports, supports auto MDI/MDIX and

store-and-forward function to make sure the packet to be sent each port

effectively. “Plug and play” function helps you set up easily. In addition, it

also supports MAC address auto-learning and aging. Moreover, it integrates

2K(S105)/1K(S108) MAC address table. Its easy setup and no network

management will benefit you a lot. Exquisite and high-stable, it is your best

choice to share the Internet.

1.1 Switch Features

Complies with the IEEE802.3 10Base-T Ethernet,

IEEE802.3u 100Base-TX Fast Ethernet standards.

Supports NWAY auto-negotiation function, auto-detect

transfer data rate, Half/Full-duplex.

Provides 5/8 10/100Mbps Auto-sensing RJ45 ports and

supports Auto MDI/MDIX.

Supports IEEE802.3x flow control for Full-duplex, and

Backpressure flow control for Half-duplex.

Supports non-blocking line speed forwarding.

Supports store-and-forward switching method.

Supports MAC address auto-learning/aging function and

integrates 2K(S105)/1K(S108)MAC address table.

1.2 Package Contents

Please check the articles carefully after you open the packing as below:

One 5/8-Port Fast Ethernet Switch

One Power Adapter

One User Guide

If any of the listed items are missing or damaged, please contact the reseller

from whom you purchased for replacement.

1.3 Front Panel and Rear Panel Specifications

The front panel of 5/8 Port Fast Ethernet Switch includes Link/Act indicators

and one power indicator. Please refer to the detailed description of these

indicators in LED Indicator Specifications

The Rear Panel of the Switch includes 5/8 10/100Mbps RJ45 ports and one

DC power port used for DC power input is located in the side panel of the

Switch.

Notice: Please use the delivery-attached power supply. If not, the

Switch may be damaged.

1.4 LED Indicator Specifications

The LED indicators of the Switch include Power and Link/Act. You can

see their operating situation through these LED indicators.

The following chart shows the LED indicators of the Switch along with

explanation of each indicator.

LED Color Status Description

Power

Green ON This indicator lights when the

Switch powers on.

— OFF

If this indicator is not lighting,

please check the DC power

connector to ensure the correct

connection of the power adapter.

Link/Act Green ON The other devices connect to the

port of the Switch.

Green Blinking The port is transmit- ting or

receiving data packets.

2. Installation

2.1 Before Connecting to the Network

Before connecting the S105/S108 to the network, please pay attention to

the following instructions:

Don’t put heavy articles on the Switch.

Power sockets and equipments should be within 1.5 meters of the

Switch.

Check power supply to confirm the safe connection.

Make sure there’s adequate space for proper heat dissipation and

adequate ventilation around the Switch.

2.2 Connecting to End Nodes

Use standard Ethernet cable to connect the Switch to end nodes as

described below. Switch ports will automatically adjust to the characteristics

(MDI-II/MDI-X, speed, duplex) of the device to which is connected.

Switch connecting to an end node

Please refer to the LED Indicator Specifications. The Link/Act LEDs for

each port lights green when the link is available.

2.3 Switch to Router or Switch

Connecting to another router or switch

Please refer to the LED Indicator Specifications. The Link/Act LEDs for

each port lights green when the link is available.

3. Product Specification

Standards IEEE802.3 10Base-T Ethernet

IEEE802.3u 100 Base-TX Fast

Ethernet

Protocol CSMA/CD

Topology Star

Network Cables 10 Base -T: Cat.3 UTP or above

100 Base -TX: Cat.5 UTP /STP

Speed 10/100Mbps

Transmission Method Fast store-and-forward

MAC Address Table 2K(S105)/1K(S108)

Packet Filtering/

Forwarding Rate 14880pps(10Mbps)per port

148800pps(100Mbps)per port

MAC Address Learning Self-learning, auto-aging.

Backplane Bandwidth 1Gbps(S105)/ 1.6Gbps(S108)

Power External universal power supply

DC INPUT DC 5V 600mA

Power Consumption 2.7W(S105)/4.2W(S108)

Operating Temperature 0℃-40℃

Storage Temperature -40℃-70℃

Working Humidity 10%～90% RH (no condensing)

Storage Humidity 5%～95% RH (no condensing)

FCC Statement

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

If you still have some problems, please contact our customer

service

Technical Support

Toll Free: 400-6622-666 (For Mainland China Only)

Toll Free: 1-800-570-5892 (For USA only)

Tel: +86 (755) 2344 2820

Skype: tendasz

MSN: tendasz@hotmail.com

Email: support@tenda.com.cn

Headquarter Shenzhen:

Add: Tenda Industrial Zone,No.34-1 Shilong Road, ShiyanTown,

Baoan District, Shenzhen, China. 518108

Tel:(86)755-27657180

Fax: (86)755-27657178

Email: sales@tenda.com.cn

Technical Support: support@tenda.com.cn

Otros manuales para S105

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Tenda

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad