Teltonika FM640 Manual de usuario
https://wiki.teltonika-gps.com/view/FM6_Testing_RS-232_and_RS-485_TCP_Link_Mode
FM6 Testing RS-232 and RS-485 TCP Link
Mode
Main Page > EOL Products > FMB640 > FMB640 Manual > FM6 Testing RS-232 and RS-485 TCP Link Mode
Contents
1 Step 1. Understanding what is FMB640 RS232/RS485 TCP Link mode
2 Step 2. Setting parameters in the configurator for TCP Ascii mode test
2.1 2.1. Message Timestamp
3 Step 3. Establishing FMB640 test link with the server through Hercules
4 Step 4. Sending from server to external device over Hercules
5 Step 5. Sending from external device to server over Terminal
5.1 Links for download
Step 1. Understanding what is FMB640 RS232/RS485 TCP
Link mode
In this mode link with an external device (for example PC) using text messages can be established.
FMB640 has to be connected to the external device through RS232 or RS485. Any string of data
coming to RS232 or RS485 will be routed to the server (if the link is currently active). Messages that
are exchanged between FMB device and server, have to be packed in Codec.12 format. Here for TCP
link establishment, we will be using Hercules. For sending messages from external devices to
servers over FMB640 Terminal will be used.
Step 2. Setting parameters in the configurator for TCP Ascii
mode test
First of all, in the FMB640 configurator you have to set parameters for RS232 or RS485 (depends on
which RS232 or RS485 port you are using) in the global parameters window.
Here in the RS232 settings section, Baudrate can be chosen for any available. The mode has to be
chosen for TCP Ascii.
2.1. Message Timestamp
Message Timestamp parameter is used to determine if it is necessary to include a timestamp in the
RS232 TCP packet when sending it to the server. If the parameter is Enabled, then Codec 13 is used
for data sending. Otherwise, Codec 12 is used.
You can also use RS485 which is also suitable for Ascii TCP Link mode. In order to make a link
between FMB640 device and server, Domain and Target Server Port have to be set in the working
device profile, GPRS data sending Settings section. When the right parameters are set, you can save
the configuration to the FMB640 device.
Step 3. Establishing FMB640 test link with the server
through Hercules
In this case, we have a PC that is considered to be a server and an external device at the same time.
When FMB640 is configured and connected to the external device, next what we have to do is to
start Hercules (Figure 2) which is on the server-side and will be used for sending/receiving
messages.
(Please keep in mind that external device RX cable needs to be connected to FMB640 device TX
cable and external device TX cable connected to FMB640 RX cable.)
Here you have to choose the TCP Server section from the upper menu. In the marked fields:
1. Write your server (PC) port and press Listen button;
2. In the Client connection status you will be able to see if a connection between server and FMB
device has started successfully;
3. In the Send field, you can write a message that is packed in Codec.12 format which will be sent to
the FMB640device.
Step 4. Sending from server to external device over Hercules
When sending a message from Hercules, first you have to pack it in Codec.12 format. If you want to
send a message to an external device over FMB640from the server, a packed message should be
pasted into the Send field in Hercules (Figure 2, marked field 3). The HEX format box should be
unchecked if the text is in HEX format (for example:
00000000000000260C01050000001e48656c6c6f2c206c657473207465737420544350206c696e6b20
6d6f64650100001aef etc.). When you press the Send button, you will see your message in the Sent
data field (Terminal). If the message is sent successfully to FMB640 you can check it in the Terminal
window.
Connect Port ½ cable one end to RS232 RX/TX cables on the FMB640device and then connect the
USB side to the computer. Please find which port is used for Port ½ cable in the device manager.
Please select correct COM Port (1). In this case, we use COM21. Then press connects (2).
Open Hercules application and just type your message in the marked field (3) and press the Send
button (4). If sent successfully, you will see it in Hercules Sent data field (Figure 4). For example test
text will be sent: Hello, lets test TCP link mode. In Codec.12 format it looks:
00000000000000260C01050000001e48656c6c6f2c206c657473207465737420544350206c696e6b20
6d6f64650100001aef
On terminal you should now receive a message:
Step 5. Sending from external device to server over Terminal
For testing data sending from external device to server, enter the text you want to send on Terminal
and press send.
You can check if data is received to a server in Hercules. Sample text: Hello, lets test TCP link mode.
Please keep in mind, that special chars (ASCII Names) need to be marked.
Links for download
1. Hercules SETUP utility
2. Terminal download
Tabla de contenidos
Otros manuales de GPS de Teltonika
Teltonika
Teltonika FMM920 Guía de instalación
Teltonika
Teltonika MSP500 Guía de instalación
Teltonika
Teltonika TAT240 Manual de usuario
Teltonika
Teltonika FMB122 Guía de instalación
Teltonika
Teltonika T-Box/GPS-800 Manual de usuario
Teltonika
Teltonika FMB225 Manual de usuario
Teltonika
Teltonika GH5200 Manual de usuario
Teltonika
Teltonika FMM00A Guía de instalación
Teltonika
Teltonika FMB110 Guía de instalación
Teltonika
Teltonika MH2000 Manual
Teltonika
Teltonika FM1100 Manual de usuario
Teltonika
Teltonika FMM80A Guía de instalación
Teltonika
Teltonika FMB930 Manual de usuario
Teltonika
Teltonika FMC650 Guía de instalación
Teltonika
Teltonika FMC920 Guía de instalación
Teltonika
Teltonika FMC130 Guía de instalación
Teltonika
Teltonika Telematics FMC150 Manual de usuario
Teltonika
Teltonika FMC00A Guía de instalación
Teltonika
Teltonika FMP100 Manual de usuario
Teltonika
Teltonika FMB003 Guía de instalación
