Teleorigin RB900-Pro Manual de usuario

Contents

 
 
 
 
 
2
Overview 4 
References 5 
Package 6 
1 Box 6 
Complete package contents 7 
General presentation 8 
1 Product pictures 8 
2 External connections 9 
2.1 GSM antenna connector 9 
2.2 Bluetooth antenna connector 10 
2.3 RS-232 Interface (EIA574) 11 
2.4 Power supply connector 12 
2.5 SIM card holder 13 
3 Product sticker 14 
Basic features and services 15 
Using the modem 16 
1 Setting up the modem 16 
2 Mounting the modem on the wall 16 
3 Checking the communication with the modem 17 
4 Status of the modem (LEDs) 17 
5 Disabling and enabling echo function 18 
6 Verifying the strength of received signal 19 
7 PIN code status 19 
8 Network registration 20 
8.1 GSM network registration 20 
9 GPRS network registration 21 
10 AT commands summary 22 
Troubleshooting 23 
1 No connection/communication with the modem 23 
2 Receiving ERROR message 23 
3 Receiving NO CARRIER message 24 
Technical characteristics 25 
1 Mechanical characteristic 25 
2 Housing description (dimensioning diagram) 25 
Electrical characteristic 26 
1 Power supply 26 
2 RF characteristics 26 
3 External antenna 27 

 
3
4 Environmental characteristic 27 
Safety recommendations 28 
1 General Safety 28 
2 Care and Maintenance 28 
3 Responsibility 28 
ConformityAssessment Issues 29 
Safety Recommendations 30 
List of Acronyms 31 
On-line support 33

Overview

The RB900-Pro terminal is the complete modem solution for wireless m2m applications.

Based on the high quality module, RB900-Pro offers high level GSM/UMTS/LTE Cat. 1,

GPIO and optional Dual SIM, MIMO, OneWire, GNSS receiver and internal battery

features in compact aluminum housing with all the standardized interfaces. Its small size

and wide supply voltage range, make it easy to integrate into all kinds of machines.

The RB900-Pro modem series, offering e-mail, TCP/UDP data transmission, SMS and

SMTP communication is a universal solution for all low-volume M2M and mobile data

applications including metering, traffic systems, transportation and logistics, security,

vending machines, and facility management.

The device can be controlled by standard AT commands or by customer's own

application, thus making it the smallest, most complete SMT platform for m2m solutions.

This document contains a full description of the RB900-Pro modem and gives

information about installation and use.

References

[1] Quectel_EC25&EC21_AT_Commands_Manual_V1.1.pdf

Package

Box

On the original box, you will find the product sticker. It should match modem sticker on

the device. This verifies that your modem is an original product. More information about

stickers in Product sticker.

Complete package contents

Complete package contains:

•RB900-Pro terminal (item A)

•antenna (item B)

•power supply with 4-pin (item C)

•2-pin GPIO cable 1,5m open end (item D)

•1-pin GPIO cable 1,5m open end (item E)

General presentation

Product pictures

SMA antenna

connector

Extractable

SIM card

holder

SIM card holder ejector

TR switch

DATA

GSM

PWR

LEDs

Serial DE15 D-sub connector

Power supply and I/O connector

IO connector

USB interface

External connections

GSM antenna connector

An SMA antenna input is used to connect an external GSM antenna. To establish a

connection with a GSM network, an external antenna must be used. Type of antenna

depends on the GSM coverage. In good circumstances (level of received signal is high)

use the antenna supplied in the package. If the range of GSM is low or none, an outdoor

or indoor (for instance in a place where GSM range is sufficient) antenna should be used.

Note: If there is no antenna connected to the SMA connector, connection with a GSM

network is impossible.

D-Sub 15-pin connector

The RB900-Pro terminal is equipped with a D-Sub DE15F 15-pin connector to control

the RS232 interface, RS232 AUX/Debug/MCU/Modem (option) or RS485 Modem/MCU

(option).

Table of DB9 pins:

Pin No.

Name

Dir

Description

DCD

OUT

Data Carrier Detect. Raised by DCE when modem

synchronized.

TXD

Transmit Data (a.k.a TxD, Tx). Sending data from DTE.

Boot

Modem boot

RXD

OUT

Receive Data (a.k.a RxD, Rx). Arriving data from DCE.

DSR

OUT

Data Set Ready. Raised by DCE to indicate ready (optionally

RS485 A)

DTR

Data Terminal Ready. Raised by DTE when powered on. In

auto-answer mode raised only when RI arrives from DCE.

GND

Ground

CTS

OUT

Clear To Send. Raised by DCE in response to RTS from DTE.

RTS

Request To Send. Raised by DTE when it wishes to send.

Expects CTS from DCE.

OUT

Ring Indicator. Set when incoming ring detected - used for auto-

answer application.

Reset

Modem reset

NC*

Not connected in standard version*

* - Analog Input 0, 0-10V as an option

Tabla de contenidos

Otros manuales de Módem de Teleorigin

Teleorigin

Teleorigin RB900SG Manual de usuario

Teleorigin

Teleorigin RB900SG Manual de usuario

Teleorigin

Teleorigin RB900 Manual de usuario

Teleorigin

Teleorigin RB IndustrialRT Manual de usuario

Teleorigin

Teleorigin RB900SG Manual de usuario

Teleorigin

Teleorigin RB900 Manual de usuario

Teleorigin

Teleorigin RB800 Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario