Technogym Selection Multi Hip Manual de usuario
1
S E L E C T I O N
T H E S T R E N G T H E V O L U T I O N
Multi Hip
User manual
All equipment
2
Multi Hip
Contents
Identification of the manufacturer and equipment ............................ 3
Description of the equipment............................................................ 4
Technical data ................................................................................... 6
Safety devices and warnings ............................................................ 7
Place of installation ........................................................................... 9
Fitting the number holder ................................................................ 10
Lifting and moving the equipment................................................... 11
Adjusting the equipment ................................................................. 14
Assembly ........................................................................................ 15
Routine maintenance ...................................................................... 18
Replacing the padded parts............................................................ 19
Replacing the cable......................................................................... 20
Adjusting cable tension ................................................................... 22
Technical Service............................................................................. 23
Storage............................................................................................ 24
Disposal........................................................................................... 25
Using the equipment ....................................................................... 26
User manual ...................................................................................... 1
Contents............................................................................................ 2
3
Multi Hip
D
E
A
B C F
Identification of the manufacturer and equipment
The equipment and manufacturer identification plate, placed behind the central frame, gives the following details:
AManufacturer's name and address
BCE Mark
CSerial number
DMaximum user weight
EEquipment classification
FConsultation of user manual required
4
Multi Hip
H
L
B
A
C
I
D
O
E
G
F
Description of the equipment
A Platform: where the user stands to perform the exercise.
B Lever: operated by the user by means of the roller (C); before starting to exercise, or between one set and the next, the ROM
device may be used to adjust the starting position thus modifying the range of motion.
D ROM device: system for adjusting the Range of Motion and the starting position of roller (C) . Adjustments are made by pulling knob (L).
E Front handgrip: it is fixed to frame (O) and is not influenced by the adjustments of the central frame (I).
F Weight stack: lever (B), operated by the user, moves the weights along two guides by means of a cable. A pin (G) is used to select
the load, and adjust the level of intensity of the exercise. Cursor (H) is used to vary the selected workload by 2.5 kg.
5
Multi Hip
D
M
N
O
I
C
Description of the equipment
I Central frame: supports the ROM (D) and the handgrips (M). The height of the central frame can be adjusted by pulling knob (N). This
adjustment makes it possible to adapt the height of handgrips (M) and roller (C) to the height of the user.
M Handgrips: the user must hold them to ensure a correct position during exercises. They are height-adjustable, together with
roller (C), by pulling knob (N).
O Main frame: load-bearing structure of the equipment.
6
Multi Hip
275 kg (606 lb) + 312 kg (688 lb)
95 kg (190 lb) + 125 kg (250 lb)
1220 mm
(48")
1530 mm
(61")
1123 mm
(44")
Technical data
7
Multi Hip
Safety devices and warnings
The maximum user weight is 180 kg.
The outside of the weight stack is covered by a protective panel.
The equipment has no sharp corners.
All parts which come into contact with the user's body are suitably protected with rubber coverings or padding.
Pay particular attention to the parts of the equipment with labels indicating “BEWARE OF
CRUSHING”.
This symbol accompanies safety warnings and is used to draw attention to potential risks of personal injury. Pay attention
to all safety warnings accompanied by this symbol to avoid possible injury.
WARNING
During all operations involving transport, maintenance and cleaning, pay attention to any part of the equipment where
body parts may become trapped.
8
Multi Hip
Safety devices and warnings
WARNINGS
Attention must be paid to the labels attached to the equipment, as they provide
information about possible risks and hazards.
We recommend immediately replacing the labels when they become damaged or difficult
to read.
9
Multi Hip
Place of installation
To ensure safe, comfortable and effective use of the equipment, the place of installation must comply with certain specific requirements;
in particular, before choosing where to install the equipment we recommend that you check that the following conditions are available:
- a temperature between +10°C and +25°C;
- sufficient ventilation to maintain a humidity level between 20% and 90%, when the equipment is in use;
- sufficient lighting to make the area a safe and relaxing place to exercise;
- sufficient clearance on all sides of the equipment, taking into account its maximum dimensions when in use, to ensure safety;
- a flat, stable and vibration-free floor surface, with sufficient load bearing capacity for the equipment’s weight.
If the equipment is to be installed in a public recreation area, the place of installation must comply with all the requirements of the
regulations currently in force.
WARNING
The equipment must be installed and used in a place where access and supervision are specifically controlled by the
owner.
10
Multi Hip
A
B
Fitting the number holder
The number holder must be installed immediately under the top: standing facing
the equipment, fix the number holder to the left tube supporting the guide, so
that it is flush with the rubber stop of the guide.
The number holder is made up of two sections: the larger section (A) must be
placed at the front; the curved closing section (B) must be placed at the back of
the equipment.
Insert the two screws (Tbic M5x6 Z) from the front of the equipment, coupling them
with the two M5 cap nuts at the rear; then tighten the nuts using the appropriate
spanners.
The number holder is optional.
Otros manuales para Selection Multi Hip
1
Tabla de contenidos
Otros manuales de Equipo de fitness de Technogym
Technogym
Technogym Selection Adductor Manual de usuario
Technogym
Technogym CROSS FORMA Manual de usuario
Technogym
Technogym Selection Chest Incline Manual de usuario
Technogym
Technogym FLEXability ME05 Manual de usuario
Technogym
Technogym Kinesis Station Manual de usuario
Technogym
Technogym Selection Abdominal Crunch Manual de usuario
Technogym
Technogym Selection Manual de usuario
Technogym
Technogym Selection Low Row Manual de usuario
Technogym
Technogym MULTIPLA Manual de usuario
Technogym
Technogym Kinesis Station Manual de usuario
Technogym
Technogym Kinesis Station Manual de usuario
Technogym
Technogym Element+ Manual de usuario
Technogym
Technogym SKILLROW Manual de usuario
Technogym
Technogym Cable Stations Manual de usuario
Technogym
Technogym Element+ Lower Back Manual de usuario
Technogym
Technogym SYNCHRO ARTIS Manual de usuario
Technogym
Technogym CLIMB ARTIS Manual de usuario
Technogym
Technogym Element+ Manual de usuario
Technogym
Technogym MyRun Manual de usuario
Technogym
Technogym Excite Live DF Series Manual de usuario
