ParaBody Serious Steel 877102 Manual de usuario
Serious Steel
877102 BODYSMITH NARROW
WORKOUT CENTER
I
ASSEMBLY INSTRUCTIONS
Part # 6757301 t~.evlision:1/12/98
[ IMPORTANTNOTES’]
WELCOMETO THE WORLDOF
Please note:
* Thank you for purchasing the Parabody 877102 BODYS1VHTHNARROWWORKOUT
CENTER.Please read these instructions thoroughly and keep them for future reference.This
product mustbe assembledon a flat, level surface to assure its proper function.
*Werecommendcleaning your product (pads and flame) on a regular basis, using warmsoapy
water. Touch-uppaint can be purchased from your Parabody customer serv~ice representative
at (800) 328-9714.
There is a risk assumedby individuals whouse this type of equipment. To miniraize risk, please
follow these rules:
1. Inspect equipmemdaily. Tighten all loose connections and replace wornpa:~ts immediately.
Failure to do so mayresult in serious injury.
2. Donot allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment,call your local Parabodydistributor or call the
Parabody customer service department at (800) 328-9714.
5. Consult a physician before beginning any exercise program.
[ Tools Required for Assembly
* 3/4" wrench
* 9/16" wrench
*Ratchet with 3/4" and 9/16" sockets
* Adjustable wrench
* Tape measure
Bolt LengthRuler
NOTE: BOLTLENGTHIS MEASUREDFROMTHEUNDERSIDEOF TH-E HEADOF THE BOLT.
BOLT LENGTHRULER:
~llll!iiil
BOLT LENGTH
1/2 ] 1/2 I1/2 [ 1/2 [ 1/2 I 1/2 6
I..........
p,,ARTS LIST
KEY
1
2
3
4
PART#
6407103
6407503
6100402
DESCRIPTION
UPRIGHT FRAME
BENCH FRAME
HEIGHT ADJUSTMENT BAR
QTY
1
1
1
1
6406602
5 6407802
6 6407302
WOLFF SLEEVE
BASE LEG
L
SADDLE 2
7
11
12
13
14
15
16
17
18
19
6024702
6407202 LEG EXTENSION NECK 1
1
6406401
6406501
6125101
61’94601
6654502
6654102
3102909
3102922
3102904
3102910
3102501
20 3102601
21 3102804
22
23
24
25
26
27
28
29
30
31
32
33
3102502
6236701
3102804
6412001
6020601
LEG EXTENSION
HINGE TAB
’"U’PIN
ROLLER PAD SHAFT
" ’ ROLLER PAD
SEAT PAD
BAcKPAD
3/8 X 1" BOLT
3/8 X 2-3/4" BoLT
3/8 X 3" BOLT
1/2 X 3" BOLT
3/8" WASHER
3/8" LOCK WASHER
3/8" LOCKNUT
1/2" WASHER
1-3/4" SQ. ENDcAP
1/2" LOWHEIGHT LOCKNUT
3/8" SPRING PIN ASSEMBLY
1/2" FLANGEBEARING
3105401 3/4" STARLOCKCOLLAR
3109602 PAL NUT
6145801 THUMBSCREW
3103101
6416601
3104301
6405201
1-1/4 X 5" GRIP
PARAGLIDESTRIP (8 ct.)
3/4" sO. RUBBER,BUMPER
2" SO. ENDCAP
4
2
2
1
10
4
3
2
4
1
3
2
6
2
4
2
3
6
4
2
FIGURE1
STEP1:
¯Attach eight PARAGLIDESTRIPS(31) to the WOLFFSLEEVE(4) (FOURONEACHEND)as shown in FIGURE1 using
following steps:
¯ Thoroughly clean all surfaces where the PARAGLIDESTRIPSare to be attached.
¯ Removethe PARAGLIDESTRIPSfrom the paper backing and fLrmly apply them to all shownsurfaces.
¯Insert one U-PIN(10) through the BUSHINGof the WOLFFSLEEVE(4) and attach one PALNUT(28) to the end of the
(10) as shownin FIGURE
¯SECURELYassemble one 3/8" SPRINGPIN ASSEMBLY(25) to the SPRINGPIN HOUSINGon file WOLFFSLEEVE(4)
shown in FIGURE1. (!!! IMPORTANT!!! TIGHTENTHE NUTOF THE SPRING PIN ASSE~cIBLY SECURELY)
1/2 I 1/2 I 1/2 I 1/2 I 1/2 I 1/2 6
FIGURE 2
STEP2:
¯Pull back the SPRINGPIN on the WOLFFSLEEVE(4) and slide it over the end of the BENCHFt?~AelE(2) as shown
FIGURE2. Engagethe SPRINGPIN into one of the adjustment holes.
¯ Insert two 2" SQ. ENDCAPS(33) into both ends of the BASELEG(5) as shownin FIGURE
¯Insert one U-PIN(10) through the BUSHINGon the bottom of BENCHFRAME(2) and attach one PALNUT(28) to the
the U-PIN(10) as shownin FIGURE
¯Insert the BASELEG(5) into the front of the BENCHFRAME(2) as shown in FIGURE2. (MAN~ESURETHATTHE
ON THE BASE LEG IS UNDERTHE BENCHFRAME)
FIGURE 3
STEP3:
¯ Insert four 2" SQ. ENDCAPS(33) into the BASETUBESof the UPRIGHTFRAME(1) as shown in :FIGURE
¯SECURELYassemble the BENCHFRAME(2) to the UPRIGHTFRAME(1) using two 3/8 X 3" BOLTS(17), one 3/8
4" BOLT(16), six 3/8" WASHERS(19), and three 3/8" LOCKNUTS(21) as sho~vn in FIGURE
¯SECURELYassemble two 3/8" SPRINGPIN ASSEMBLIES(25) to the SPRINGPIN HOUSINGon the UPRIGHTFRANIE(1)
as shown in FIGURE3. (NOTE:!!!IMSPORT~MNT!!!Tighten the nut of the SPRINGPIN ASSEM]~LYSECURELY!)
¯ Secure the WOLFFSLEEVE(4) in place with one THUM]3SCREW(29).
~1/2 T 1/2 [ 1/2 ] 1/2 ~ 1/2 ]
6
FIGURE4 i]
;TEP4:
¯Attach eight PARAGLIDESTRIPS (31) to both UPRIGHTTUBESon the UPRIGHTFRAME(1) (FGURONEACHEND)
shownin FIGURE4 using the following steps:
¯Thoroughlyclean all surfaces where the PARAGLIDESTRIPSare to be attached.
¯Removethe PARAGLIDESTRIPSfrom the paper backing and firmly apply them to all shownsurfaces.
¯ Attach eight PAlL&GLIDESTRIPS(31) to each SADDLE(6) (FOURONEACHEND)as shown in FIGURE
¯Slide two 1-1/4 X 5" GRIPS(30) over the DIP HANDLESof both SADDLES(6). (IF A LUBRICANTIS REQUIRED,
THE INSIDE OF THE GRIP WITHRUBBINGALCOHOL.)
¯Pull back the SPRINGPIN on the UPRIGHTTUBES,and insert the SADDLES(6) as sho~vn in FIGURE4.. Slide the SADDLE
(6) do~vrtto the desired height and release the SPRINGPINinto the hole.
¯ Secure the SADDLES(6) in place with two THUMBSCREWS(29) as shown in FIGURE4. Whenready to perform the
EXERCISE,simply insert the SADDLES(6) into the UPRIGHTTUBESand tighten the two THUMBSCREWS
7
FIGURE 5
;TEP5:
¯ To assemble the SEATPAD(13) to the WOLFFSLEEVE(4), start by sliding two HINGETABS(9) over the PIN
WOLFFSLEEVE(ONEONEACHSIDE) as shown in FIGURE5, and SECURELYassemble each HINGETAB(9) to
SEATPAD(13) using two 3/8 X 1" BOLTS(15), 3/8" LOCKWASHERS (20), and tw o 3/ 8" WASHERS (19).
SURE BOTHHINGE TABS ARE ALL THE WAYON TI:IE PIN)
1/2 I 1/2 I 1/2 I 1/2 I 1/2 I 1/2 6
1[ I I I
o[ I I
I I 8
3/8 X1"1
FIGURE 6
;TEP6:
¯ Toassemble the BACKPAD(14) to the WOLFFSLEEVE(4), slide the two remaining HINGETABS(9) over the PIN
WOLFFSLEEVE(ONEONEACHSIDE) as shown in FIGURE6, and SECURELYassemble each HINGETAB(9) to
BACKPAD(14) using two 3/g X 1" BOLTS(15), two 3/8" LOCKWASHERS(20), and two 3/8" WASHERS(19).
SURE BOTH HINGE TABS ARE ALL THE WAYON THE PIN)
FIGURE7
STEP7:
¯ Insert one 1-3/4" SQ. ENDCAP(23) into the top of the LEGEXTENSIONNECK(7) as sho~vnin FIGURE
¯Slide t~vo ROLLERPADS(12) over each end of the SHAFTof the LEGEXTENSIONNECK(7), as shownin FIGURE7,
secure in place using two 3/4" STARLOCKCOLLARS(27).
¯Insert the LEGEXTENSIONNECK(7) into the BENCHFRAME(2) and secure in place using on THUMBSCREW(29)
shownin FIGURE7.
1/2 [ 1/2 [ 1/2 l 1/2 I 1/2 I 1/2 6
4l I I _L.
2[ I I
1[ I ~ I
I I I 10
Tabla de contenidos
Otros manuales de Equipo de fitness de ParaBody
ParaBody
ParaBody 824 Manual de usuario
ParaBody
ParaBody 826 Manual de usuario
ParaBody
ParaBody PBF 472 Manual de usuario
ParaBody
ParaBody 821 Manual de usuario
ParaBody
ParaBody Serious Steel 360101 375 Manual de usuario
ParaBody
ParaBody 838 Manual de usuario
ParaBody
ParaBody Serious Steel 359101 Manual de usuario
ParaBody
ParaBody 807 BODYSYSTEM Manual de usuario
ParaBody
ParaBody 908101 ST Manual de usuario
ParaBody
ParaBody 778 Manual de usuario
ParaBody
ParaBody 704101 Instrucciones de montaje
ParaBody
ParaBody 829 Manual de usuario
ParaBody
ParaBody Leg Press Factor 625 Guía de instalación
ParaBody
ParaBody 827103 Manual de usuario
ParaBody
ParaBody 813 Manual de usuario
ParaBody
ParaBody 830 Manual de usuario
ParaBody
ParaBody 877 Instrucciones de montaje
ParaBody
ParaBody 822104 Manual de usuario
ParaBody
ParaBody 824 Manual de usuario
ParaBody
ParaBody 872101 Instrucciones de montaje
