TE Connectivity AMPLIMITE HDP-20 Manual de usuario

Instruction Sheet

AMPLIMITE* High Density (HDP- 20) 408--7514

LOC B

1of 2

E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company

TE logo is a trademark.

*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.

TOOLING ASSISTANCE CENTER 1--800--722--1111

PRODUCT INFORMATION 1--800--522--6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

10 Mar 11 Rev EConnectors with Crimp- Type Contacts

Figure 1

Shell

(Ref)

Insert

(Ref) Receptacle

Connector

(Front)

Numbered

Cavities

Plug Connector

(Back)

1. INTRODUCTION

This instruction sheet covers contact and wire

selection, application tooling, and attaching hardware

for AMPLIMITE High Density (HDP--20) Connectors

shown in Figure 1. Read these instructions thoroughly

before assembling any connectors.

All dimensions on this document are in metric

units [with U.S. customary units in brackets].

Figures and illustrations are for reference only

and are not drawn to scale.

Reasons for reissue of this document are provided in

Section 6, REVISION SUMMARY.

2. DESCRIPTION (Figure 1)

The connectors are designed for rear insertion and

extraction of size 20, precision formed contacts. The

HDP--20 connectors feature steel shells and black

polymer inserts with plastic contact retention tines.

3. CONTACTS (Figure 2)

3.1. Selection

Refer to the table in Figure 2, and select strip or

loose--piece pin and socket contacts according to the

wire size and insulation diameter to be used.

Notice that each contact cavity is number--coded

(front and back). Make certain that the cavities of the

plug are a mirror image of the receptacle. Insert pin

contacts into the back of plug and mating socket

contacts into the back of the receptacle. If all cavities

are not used, distribute contacts evenly throughout

connector.

3.2. Crimping

Strip--form contacts are designed to be crimped with a

semi--automatic or automatic machine and applicator.

Consult your local TE Representative for assistance

in selecting the machine and applicator for your

application.

Loose--piece precision formed contacts are designed

to be crimped with the hand crimping tools listed in

the table in Figure 2. Refer to the instruction sheet

packaged with the tool, for specific crimping

procedure and tool inspection information.

3.3. Insertion and Extraction

Insertion/Extraction Tools 91067--2 (Instruction Sheet

408--7508) and 91285--1 (Instruction Sheet

408--9404) are designed for both pin and socket

contacts. The 91067--2 tool is used with contacts for

wire size 24 to 20 AWG and the 91285--1 tool is used

withcontactsforwiresize28to24AWG.

NOTE

408- 7514

Rev E2 of 2

Precision Formed Contact

With

Insulation Support

Precision Formed Contact

Without

Insulation Support

Socket

(Typ)

CONTACT DESCRIPTION WIRE SIZE RANGE (AWG) INSULATION DIAMETER (MAX) HAND TOOL (DOCUMENT)

Precision Formed Contact 28--24 1.02 [.040] 91503--1 (408--8547)

With Insulation Support 24--20 1.52 [.060]

58448--2 (408--9357)

Precision Formed Contact 28--24 1.73 [.068]

(

)

Without Insulation Support 24--20 1.73 [.068]

91548--1

(

408--8547

)

Figure 2

4. HARDWARE

A shield and cable clamp assembly is used with the

connector to house the cable or wire projecting from

the rear of the connector and for strain relief of the

cable or wires. For additional information concerning

the use of the shield and cable clamp assembly, refer

to Instruction Sheet 408--7555.

Shielded cable clamp kits for AMPLIMITE HDP--20

connectors used with braid and foil--shielded cables

are available in all connector sizes. The cable clamps

may be used with latching blocks (208101, 745245,

and 745286) and spring latches (745255--1) for

panel--mounted or free--hanging applications. Refer to

Instruction Sheet 408--6609 for additional information.

A male screw retainer kit (5205980--1) and a female

screwlock kit (5205817--1) are used to secure mating

connectors in panel--mounted or free--hanging

applications. Refer to Instruction Sheet 408--7837 for

information.

A slide latch post kit (5206514--1) and a slide latch

clip kit (5206942--1) are also used to secure mating

connectors in panel--mounted or free--hanging

applications. For additional information, refer to

Instruction Sheet 408--6551.

Slide latch post kits and slide latches for all

AMPLIMITE HDP--20 connector sizes are available

for panel--mounted and free--hanging applications.

Refer to Instruction Sheet 408--6551 for slide latch

and slide latch post application procedure and

information.

5. PANEL CUTOUT

Before making the panel cutout, refer to Application

Specification 114--40030 to determine the number of

positions in the connector, whether it will be used with

a cable clamp or side latch, and what the required

dimensions and clearances must be.

6. REVISION SUMMARY

Since the previous release of this sheet, the following

changes were made:

SUpdated document to corporate requirements

Otros manuales de Cables y conectores de TE Connectivity

TE Connectivity

TE Connectivity QSFP-DD Guía del usuario

TE Connectivity

TE Connectivity HVA630-2phm Manual de usuario

TE Connectivity

TE Connectivity D5000-S Manual de usuario

TE Connectivity

TE Connectivity HVP800 2PHI 90 Manual de usuario

TE Connectivity

TE Connectivity DYNAMIC 5000 Series Manual de usuario

TE Connectivity

TE Connectivity Raychem LJSM Series Manual de usuario

TE Connectivity

TE Connectivity RAYCHEM D-436 Series Guía de referencia

TE Connectivity

TE Connectivity EP-II Manual de usuario

TE Connectivity

TE Connectivity 747564-9 Manual de usuario

TE Connectivity

TE Connectivity VAL-U-LOK 3-1586040-6 Manual de usuario

TE Connectivity

TE Connectivity AMPOWER 68361-1 Manual de usuario

TE Connectivity

TE Connectivity HVA630-5p Manual de usuario

TE Connectivity

TE Connectivity M12 Guía del usuario

TE Connectivity

TE Connectivity MATE-N-LOK 2 794216-1 Manual de usuario

TE Connectivity

TE Connectivity AMP NETCONNECT 1499119-1 Manual de usuario

TE Connectivity

TE Connectivity LJSU-4X Series Manual de usuario

TE Connectivity

TE Connectivity CCS1 Manual de usuario

TE Connectivity

TE Connectivity Type N Manual de usuario

TE Connectivity

TE Connectivity DRC16 Manual de usuario

TE Connectivity

TE Connectivity AMP-HDI Manual de usuario

TE Connectivity

TE Connectivity 55PC1122-16-9/96-9 Manual de usuario

TE Connectivity

TE Connectivity Miniature AMP-IN Guía del usuario

TE Connectivity

TE Connectivity AMP-LATCH Guía del usuario

TE Connectivity

TE Connectivity RF COAXIAL Manual de usuario

Manuales populares de Cables y conectores de otras marcas

Philips

Philips SWA6310 Manual de usuario

StarTech.com

StarTech.com CRJ4550PK Manual de usuario

Nohau

Nohau EMUL-IP2K-PC Manual de usuario

Foxun

Foxun SX-SP144E-HD4K2K Manual de usuario

Philips

Philips SWA3305W Manual de usuario

opticis

opticis Stretch DVIM1-1P0x Manual de usuario

Volkswagen

Volkswagen VAS 6558A Manual de usuario

NEXIBO

NEXIBO N-13 Manual de usuario

CYP

CYP PU-1H3HBTL Manual de usuario

Allen-Bradley

Allen-Bradley 1784-u2dhp Manual de usuario

Global Caché

Global Caché Flex Link Blaster Manual de usuario

Hauppauge

Hauppauge USB-Live2 Manual de usuario

Fenix

Fenix MPSV 15 Manual de usuario

BEGA

BEGA 71 085 Manual de usuario

Tesla

Tesla HPWC Manual de usuario

GAMERON

GAMERON LUXURY TV CABLE Manual de usuario

molex

molex Milli-Grid Dual row 87568 Series Manual de usuario

Burndy

Burndy Continental Industries thermOweld CRE-7 Manual de usuario