TANDBERG 3000 MXP Profile Manual de usuario

D13728.09 Page 1

Installation 3000/6000 Profile

For mounting of the Wheel base, Foot mount or Wall mount, follow the respective instructions on page 2-6.

2 Mounting

Wheel base Foot mount Wall mount

1 Unpacking

Monitor

Bolts:

Wall Bracket

Camera

Top Module

Cable Cover, Back

Cover and Base

(Wheel base option)

Camera Stand

Column

and Foot

2x Type A 2x Type B

4x Type C

4x Type D

+ 4x plugs for concrete

Wrench Remote

Control

Screw driver

(for removing the handles

on 6000 MXP Profile 50”)

User Manual on CD

4x Type E

+ 4x washers for

gypsum/plasterboard

For mounting of the Wheel base, Foot mount or the Wall mount version,

follow the respective instructions on the following pages.

D13728.09 Page 2

Wheel base

1 Disassemble the Foot from the Column.

Keep the bolts 2 Assemble the Column to the Base with

the 8 bolts from the Foot

3 Mount the Top Module to the Column

Use 4x type C

bolts in front

and on sides

from

underneath.

Use 2x type B

bolts behind,

from above.

Remove rubber band

before mounting.

Remove protection

foil from acrylic plate.

4 Lift the Monitor onto the Top Module and

connect cables

Align according to

arrow labels and lower

the Monitor into place.

Connect power

cable and DVI cable

from Top Module to

Monitor after mounting

the Monitor. Also connect

speaker and amplier cables.

Put excess cable length back behind monitor.

5a Mount the Monitor 43”/50”, for 32” see 5b

On all products, except

TANDBERG 3000

MXP 32” Prole:

Use 2x type A

bolts to xate the

Monitor.

Caution! Be careful not to squeeze ngers or cables.

Rearrange cables if necessary.

Keep the Column in the

package upside down

while disassembling

the Foot.

WARNING! Do not lift

the Column out of the

package, the small

pegs on the

Column may

dent the oor.

Assemble the Base

while the Column

stands in the package

upside down.

Then, lift the Column

and the Base out of the

package.

5b Mount the Monitor 32”

On TANDBERG

3000 MXP 32”

Prole:

Tighten the bolts

on each side of the

rear structure to

xate the Monitor.

3000/6000 Profile

7 Mount the Camera

Pull cable through Camera Stand, and

place it behind the Monitor.

Ensure that the Camera Stand is prop-

erly connected to the magnets on top

and behind. Plug cable to Camera as

shown on gure above.

Place Camera on top. The guide pin

and magnets will ensure correct place-

ment. Please verify that the Camera is

aligned with the front line of the Monitor.

D13728.09 Page 3

Wheel base

Mount the Magnet Brackets behind the

Column and attach the Cable Cover to

the magnets. You may have to

rearrange the cables.

Mount the Back Cover on the back side

of the Top Module.

6 Mount the Cable Cover and the Back Cover

8 Connecting external devices

If external deivces are

connected to the system,

lead the cables through

the hole in the cable

cover.

3000/6000 Profile

There are access holes

provided near the base

of the column section for

cable access to the front

DVD/VCR tray and to the

rollabout base for cables

that must run to the oor.

HD VIDEO

OUT CODEC

D13728.09 Page 4

Foot mount

Warning!

Due to the size and mass of this equipment, it is very important that the wall mount unit is safely installed according to

these installation instructions and that the wall is able to safely support the product. It is highly recommended that this

Foot mount unit is installed by trained personnel.

1 A) Mount the Wall Bracket to the wall

- Studs/pillars

Make sure that the hooks

on the Wall Bracket

point upwards.

Mount 762 mm

(30”)

horizontally from

oor to underneath

wall-mount.

Use 4 type D bolts.

Make sure to select holes

that align with the wall

studs/pillars.

1 C) Mount the Wall Bracket to the wall

- Brick/Concrete wall

Make sure that the hooks

on the Wall Bracket

point upwards.

Mount 762 mm

(30”)

horisontally from

oor to underneath

wall-mount.

Use 4 type D bolts

with concrete plugs.

1. Drill a small

initial hole

2. Drill a larger

hole for plugs

3. Mount into

specied

holes with

plugs and

bolts.

2 Mount the Top Module and the column to the Wall

Bracket

Step 1

Use 2x type B

bolts behind

from above

Use 4x type C

bolts in front

and on sides

from underneath.

Remove rubber

band before

mounting.

Remove protection

foil from acrylic plate.

Step 2

Tighten nuts in

position

a and b after

mounting.

3 Connect cables and mount the Monitor

Pull cable through

Camera Stand, and

place it behind the

Monitor. Ensure that the

Camera Stand is

properly connected

to the magnets on top

and behind.

Plug cables to Camera

and place camera on

top with velcro.

Disassemble the handles

at the back of the screen

with the screw driver.

(6000 MXP Prole only)

4 Mount the Camera

762 mm

(30”)

762 mm

(30”)

Caution! Be careful not to squeeze ngers or cables.

Rearrange cables if necessary.

3000/6000 Profile

1 B) Mount the Wall Bracket to the wall

- Drywall/plasterboard with minimum

thickness 13mm (1/2”)

Follow the same procedure as described in

1A) but use 4 type E bolts with 4 washers.

Drill a hole (Ø6,0mm / 1/4”) for the plug

and then fasten the type E bolts with washers.

Ø3,0mm

(1/8”)

Ø10,0mm

(3/8”)

75,0mm

(3.0”)

(Please note that the 32” Monitor

shall be mounted

as described in

5b on page 2).

Connect power

cable and DVI

cable from Top

Module to Monitor

before mounting

the Monitor.

Align according to arrow lables

and lower the Monitor into place.

Put excess cable length back behind Monitor.

HD VIDEO

OUT CODEC

Caution! Be careful not to squeeze ngers or cables.

Rearrange cables if necessary.

D13728.09 Page 5

Wall mount

Warning!

Due to the size and mass of this equipment, it is very important that the wall mount unit is safely installed according to

these installation instructions and that the wall is able to safely support the product. It is highly recommended that this wall

mount unit is installed by trained personnel.

According to Standard IEC60950 3rd ed. the wall is required to support four times the actual load, which implies that a

TANDBERG MXP Prole system must be mounted to a wall which supports:

4x 77kg=308kg/679 lbs (T6000 50”), 4x 61kg=244kg/538 lbs (T3000 42”) and 4x 49kg=196kg/432 lbs (T3000 32”).

1 A) Mount the Wall Bracket to the wall

- Studs/pillars

Make sure that the hooks

on the Wall Bracket

point upwards.

Mount the Wall Bracket

horisontally in desired

hight from oor,

recommended

762 mm (30”).

It is important that the

bracket is fastened to the

studs/pillars, using 4 type

D bolts.

Make sure to select holes

that align with the wall

studs/pillars

1 B) Mount the Wall Bracket to the wall

- Brick/Concrete wall

Make sure that the hooks

on the Wall Bracket

point upwards.

Mount the Wall

Bracket horisontally

in desired hight from

oor, recommended

762 mm (30”).

Use 4 type D bolts

with concrete plugs.

1. Drill a small

initial hole

2. Drill a larger

hole for plugs

3. Mount into

specied

holes with

plugs and

bolts.

Pull cable through

Camera Stand, and

place it behind the

Monitor. Ensure that the

Camera Stand is

properly connected

to the magnets on top

and behind.

Plug cables to Camera

and place camera on

top with velcro.

4 Mount the Camera

2 Mount the Top Module to the Wall Bracket

Tighten nuts

in position

a and b after

mounting.

3 Connect cables and mount the Monitor

762 mm

(30”)

Ø�3,0�mm

(0,1”)

Ø�10,0�mm

(0,4”)

75�mm

(3,0”)

3000/6000 Profile

(Please note that the 32” Monitor

shall be mounted

as described in

5b on page 2).

Connect power

cable and DVI

cable from Top

Module to Monitor

before mounting

the Monitor. Also connect

speaker and amplier cables.

Align according to arrow lables

and lower the Monitor into place.

Put excess cable length back behind Monitor.

762 mm

(30”)

HD VIDEO

OUT CODEC

Touch tonesSnapshot

Camera Presets

D13728.09 Page 6

Installation

2. Language

Open ‘General’. Select language and press save.

3b. ISDN Conguration

Open ‘Network - ISDN Settings’. Select ISDN-BRI

Settings or ISDN-PRI Settings. Make ISDN conguration

and press ‘Save’.

1. Open the Control Panel

Choose ‘Control Panel’ from the main menu and

press OK.

3 System Conguration

3a. LAN Conguration

Open ‘Network - LAN Settings’. Make IP/H.323

conguration and press ‘Save’.

Please read the user manual for further details.

TIP

If the menu is not already present, press the

OK/Menu key on the remote control

to open the menu. Navigate the menu

with arrow keys and OK

OK/Menu

button

3000/6000 Profile

Otros manuales para 3000 MXP Profile

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de conferencias de TANDBERG

TANDBERG

TANDBERG 880 MXP Manual de usuario

TANDBERG

TANDBERG MPS 200 Manual de servicio

TANDBERG

TANDBERG C Series Manual de usuario

TANDBERG

TANDBERG Profile 42" Manual de usuario

TANDBERG

TANDBERG E20 Manual de servicio

TANDBERG

TANDBERG 1000 MXP Manual de usuario

TANDBERG

TANDBERG Codec C90 D14129.02 Manual de servicio

TANDBERG

TANDBERG Telepresence T3 Manual de usuario

TANDBERG

TANDBERG T2000 MXP Manual de usuario

TANDBERG

TANDBERG 3000 MXP Profile Manual de usuario

TANDBERG

TANDBERG 550 MXP Manual de usuario

TANDBERG

TANDBERG 150 MXP Manual de usuario

TANDBERG

TANDBERG 880 Manual de usuario

TANDBERG

TANDBERG 100MXP Manual de usuario

TANDBERG

TANDBERG MXP F8 - Manual de servicio

TANDBERG

TANDBERG Codec C60 Manual de usuario

TANDBERG

TANDBERG 6000 Manual de usuario

TANDBERG

TANDBERG Edge 95 MXP Manual de usuario

TANDBERG

TANDBERG EDGE 75 Manual de usuario

TANDBERG

TANDBERG Codec C Series Manual de usuario

TANDBERG

TANDBERG 150 MXP Manual de usuario

TANDBERG

TANDBERG Maestro MXP Manual de usuario

TANDBERG

TANDBERG 3000 MXP Profile Manual de usuario

TANDBERG

TANDBERG EX90 Manual de usuario

Manuales populares de Sistema de conferencias de otras marcas

Kramer

Kramer VIA GO Manual de usuario

AVT

AVT MAGIC AC1 Go Manual de usuario

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manual de usuario

Sony

Sony PCS-I150 Manual de usuario

Middle Atlantic Products

Middle Atlantic Products VTC Series Manual de usuario

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guía

Speakerbus

Speakerbus iD 712 Manual de usuario

Trelleborg

Trelleborg SafePilot CAT PRO Manual de usuario

Sennheiser

Sennheiser ADN Manual de usuario

ADTRAN

ADTRAN NetVanta 7100 Manual de usuario

AINA

AINA PTT Voice Responder Manual de usuario

Yamaha

Yamaha ProjectPhone PJP-100H Manual de usuario

vissonic

vissonic VLI Series Manual de usuario

Panasonic

Panasonic KX-VC500 Manual de usuario

Poly

Poly Trio 8300 Manual de usuario

Crestron

Crestron Mercury CCS-UCA-SMK Dibujo dimensional

Inmarsat

Inmarsat mini M Manual de usuario

Tenveo

Tenveo ALL-IN-ONE Manual de usuario