Swann SW351-CAC Manual de usuario

MCAC170510E

SW351-CAC

www.swannsecurity.com

Operating Instructions

Ceiling Alarm

SW351-CAC

™

Advanced security made easy

222

About the PIR Unit

PIR Alarm Unit

Mounting bracket

Mounting Hardware

Remote Control

Operating Instructions

Contents

About the PIR Unit 2

IMPORTANT - Read Before Installing 3

Detection Area 4

Installation Instructions 5

Operating the Ceiling PIR Unit 6 - 7

Warranty / Technical Support Rear Cover

Foreword

Congratulations on your purchase on this passive infrared alarm unit from

Swann! This stand-alone alarm unit will help you protect and safeguard

almost any location you want. It’s easy to install and totally wireless.

Package Contents:

How it works:

The PIR sensor is a passive infrared motion sensor, meaning it detects

infrared radiation rather than projecting it (unlike a security camera with

infrared night vision, which is active infrared). All objects emit this infrared

radiation (we commonly call it “heat”) and the infrared sensor looks for

any of this radiation which moves.

The passive sensor is not infallible – in particular, it cannot detect objects/

people which are the same temperature as their background. So a human

being moving about on an extremely hot day might go unnoticed. Also,

a security camera with active infrared night vision in the same vicinity as

the infrared sensor may give false alarms (particularly if it is a moving PTZ

system).

Do not• expose any part of the alarm unit to any sudden shocks (such as being

dropped or struck).

Do not• install the passive infrared (PIR) alarm unit within detection range of

any device which emits heat or cold, such as air conditioners, refrigerators,

ovens, heaters, microwaves or other electronic equipment which generates

heat as a by-product of operation.

Do not• install the PIR sensor in direct sunlight.

Use only alkaline batteries.•

All components are for indoor use only.• Do not install outdoors.

Replace the batteries in the unit every six months.•

Test the alarm periodically• (every 1 - 2 months and each time you change

the batteries) to ensure it is working properly.

Keep this operating instruction booklet in a safe place.•

This alarm system is designed to be, and acts as, a theft deterrent. This•

system, like any other, cannot offer complete protection for your home

or business - it is simply an alarm system. Like all practical systems, it has

limitations and it could be disabled by a skilled intruder. We suggest that you

avoid relying solely on the Ceiling Alarm to protect your property, but use it

as part of a comprehensive security solution. You can increase your level of

protection through the use of high-quality locks, stronger doors, guards for

your windows and a CCTV system and recording devices.

Important - Read Before Installing

444

Detection Area

Detection Area:

The PIR sensor has a 360 degree detection ﬁeld horizontally, and slightly more than

100 degrees vertically. The diagram below shows an average detection pattern

under typical circumstances.

The effective detection area does depend on the height of the ceiling that the

alarm unit is mounted on. As a general rule, the effective detection radius when

mounted on a ceiling of average height is approximately 9ft/3m.

You can test the functionality of the motion sensor as well as the detection area by

setting up the sensor, setting it to chime mode and then moving about in the area

you want to protect. It will chime each time it detects movement, allowing you to

obtain an accurate impression of it’s ﬁeld of view. Note that the effective detection

range may change in different environmental conditions, particularly during very

hot periods.

Important:

Any obstructions in the environment will reduce the sensors effectiveness. It•

can’t see through walls! Even a thin sheet of glass will signiﬁcantly impair the

range of the sensor, as glass blocks more infrared radiation than visible light.

Small animals (such as dogs, cats or similar) can trigger the PIR sensors.•

Therefore, we suggest that the PIR sensors are not suited to areas where pets

are kept.

The remote control uses infrared light to communicate with the alarm unit.•

For the easiest day-to-day operation of the alarm, mount the alarm unit in a

location which allows the remote control a clear line of sight from the position

you’d like to disarm it from.

Feet / Meters

6ft/2m

6ft/2m 12ft/4m 18ft/6m 25ft/8m

12ft/4m

Installation Instructions

Mounting

To mount the PIR alarm unit, you’ll need the following tools:

A screwdriver•

A drill (for hardwood or masonry)•

The PIR alarm unit should be mounted on a ceiling between 6ft/2m and 9ft/3m

high for maximum coverage and reliability.

Do not mount the PIR on a ceiling higher than 4m, as the sensor’s range will not

reach the ground, and will not be able to detect the heat of a single human body

reliably.

You could conceivably mount the alarm unit on a wall. The alarm would still work,

though the ﬁeld of view isn’t particularly suited to this application. Under most

circumstances, a more focused PIR sensor designed to be wall mounted would be

more appropriate for that purpose.

To mount the alarm unit:

The PIR sensor mounts in much the same way as a cordless smoke alarm. A circular

bracket is attached to the ceiling by screws, and then the main alarm unit is

attached to this bracket.

First, attach the mounting bracket to a ceiling, using the supplied screws. If1.

mounting on to hardwood, you may need to drill guide holes. If mounting

onto masonry (brick, concrete and so on) you’ll need a drill with a masonry drill

bit, and use the wall plugs included with the alarm unit.

Push the alarm unit onto the mounting bracket. Turn clockwise to secure in2.

place.

666

Operating the Ceiling PIR Unit

Alarm / Chime Mode

The switch to select the mode the

sensor operates in can be found

on the side of the remote control,

as shown to the left.

Alarm Mode: When the sensor detects movement whilst the unit is in alarm

mode, it will not activate immediately. There is a thirty second delay, to allow you

to use the remote control to disarm the sensor before it goes off. If the alarm unit

is not disarmed within this thirty second delay, then the alarm will sound at full

volume. The alarm can still be disarmed whilst the alarm is sounding by pressing

the disarm button on the remote control.

Chime Mode: When the sensor detects movement when in chime mode, it will

sound a chime instantly. There is no entry delay nor exit delay. After the chime

sounds, there is a short (a few seconds) delay before it can be sounded again to

prevent is sounding constantly if, for example, someone were to be standing in

the detection range.

Arming and Disarming the System

To arm the system, simply press ARM on the remote control. The system will arm

into whichever mode is currently selected on the remote control.

To disarm the system, press the DISARM button. The DISARM button will disarm

the alarm unit whether it is in Chime Mode or Alarm Mode.

Entry and Exit Delays

Once you’ve armed the alarm unit, it will enter the arming delay. This period

consists of forty-ﬁve seconds, during which time the LED on the front face of the

alarm unit will ﬂash. After the arming delay has elapsed, the alarm unit will beep

once, indicating that it is armed.

Should the alarm be tripped (that is, it detects something) it will not sound instantly.

Rather, there is a further thirty second delay, to give you time to disarm the system

before the siren sounds.

Low Battery Indicator

When the batteries in the alarm unit are running out, the LED on the front of the

alarm unit will ﬂash slowly (more slowly than during the arming delay). If the LED

starts ﬂashing in this way, change the batteries immediately.

Replacing Batteries

The batteries in the alarm unit should be replaced every six months. If you’re using

the sensor in chime mode and get a lot of visitors, you may need to change them

more often. On the other hand, if you use the PIR in alarm mode, don’t arm it

often and use high quality batteries, you may not need to replace them as often.

Remove the sensor from its mounting bracket.•

On the rear side of the sensor, locate the battery compartment.•

Remove batteries•

Insert three fresh AA batteries. Do not mix battery types, and do not use•

rechargeable batteries.

Re-Pairing Remote Control

If you ﬁnd that the remote control isn’t operating properly, this indicates that the

remote control might need to be re-paired with the alarm unit. This is most likely

to happen when the batteries are changed in the alarm unit - the temporary lack

of power clears the sensor’s memory.

Remove the alarm unit from the mounting bracket.1.

Locate and push the button on the rear of the unit labeled “LEARN”. The2.

button is recessed, so you’ll need thin screwdriver or similar to push it.

The LED on the front of the alarm unit will ﬂash slowly, indicating that the3.

sensor is in Learning Mode.

Press any button on the remote control. The alarm unit will beep to conﬁrm4.

the pairing worked.

Technical Speciﬁcations

Power Requirements 3 x Alkaline AA Batteries (4.5V DC)

Modes 2 (Alarm and Chime)

PIR Detection Range > 3m (Typical – varies by environment)

PIR Detection Area 360° horizontal, 110° vertical (approx)

Chime Mode

Chime Volume > 90dB

Chime Duration 2s

Re-Trigger Delay 5s

Alarm Mode

Mode of Operation Remote control (included)

Siren Volume > 110dB

Siren Duration 30s

Entry Delay 30s

Exit Delay 45s

Re-Trigger Delay 5s

Remote Control

Power Requirements 1 x CR2032 Button Cell (3V DC)

Remote Distance > 20ft / 6m

Remote Angle 60° (approx)

888 © Swann Communications 2010

Advanced security made easy™

Warranty Information

Helpdesk / Technical Support Details

Swann Technical Support

All Countries E-mail: tech@swannsecurity.com

Telephone Helpdesk

See http://www.worldtimeserver.com for information on time zones and the

current time in Melbourne, Australia compared to your local time.

USA toll free

1-800-627-2799

(Su, 2pm-10pm US PT)

(M-Th, 6am-10pm US PT)

(F 6am-2pm US PT)

USA Exchange & Repairs

1-800-627-2799 (Option 1)

(M-F, 9am-5pm US PT)

AUSTRALIA toll free

1300 138 324

(M 9am-5pm AUS ET)

(Tu-F 1am-5pm AUS ET)

(Sa 1am-9am AUS ET)

NEW ZEALAND toll free

0800 479 266

0203 027 0979

Swann Communications warrants this product against defects in workmanship and

material for a period of one (1) year from it’s original purchase date. You must pres-

ent your receipt as proof of date of purchase for warranty validation. Any unit which

proves defective during the stated period will be repaired without charge for parts or

labour or replaced at the sole discretion of Swann. The end user is responsible for all

freight charges incurred to send the product to Swann’s repair centres. The end user is

responsible for all shipping costs incurred when shipping from and to any country other

than the country of origin.

The warranty does not cover any incidental, accidental or consequential damages aris-

ing from the use of or the inability to use this product. Any costs associated with the

fitting or removal of this product by a tradesman or other person or any other costs

associated with its use are the responsibility of the end user. This warranty applies to

the original purchaser of the product only and is not transferable to any third party.

Unauthorized end user or third party modifications to any component or evidence of

misuse or abuse of the device will render all warranties void.

By law some countries do not allow limitations on certain exclusions in this warranty.

Where applicable by local laws, regulations and legal rights will take precedence.

Swann Communications USA Inc.

12636 Clark Street

Santa Fe Springs CA 90670

USA

Swann Communications

Unit 13, 331 Ingles Street,

Citilink Estate,

Port Melbourne Vic 3207

Swann Communications LTD.

Stag Gates House

63/64 The Avenue

SO171XS

United Kingdom

Tabla de contenidos

Otros manuales de Sistema de seguridad de Swann

Swann

Swann MDRIVE2260214E Manual de usuario

Swann

Swann 2 Real & 2 Imitation Cameras Security Monitoring... Manual de usuario

Swann

Swann PRO-640 Manual de usuario

Swann

Swann Advanced SWDVK-825508C Manual de usuario

Swann

Swann NVK-460 Manual

Swann

Swann DVR8-4200 Manual de usuario

Swann

Swann SWVAK-834254C Manual de usuario

Swann

Swann SW245-SBD Manual de usuario

Swann

Swann PRO-580 Manual de usuario

Swann

Swann DVR4-Pro-Net TBA Guía de inicio rápido

Swann

Swann SW347-WAK Manual de usuario

Swann

Swann SWWHD-INTSOL Manual de usuario

Swann

Swann PRO-580 Manual de usuario

Swann

Swann DVR4-5500 Manual de usuario

Swann

Swann DVR4-1200 Manual de usuario

Swann

Swann SWIFI-ISIREN Manual de usuario

Swann

Swann HD Pro-Series Manual de usuario

Swann

Swann NVW-600CMB Manual de usuario

Swann

Swann PRO-530 Manual de usuario

Swann

Swann DVR4-2500 Manual de usuario

Swann

Swann SW244-SKI Manual de usuario

Swann

Swann SW343-DP2 Manual de usuario

Swann

Swann Alpha D04C1 Manual de usuario

Swann

Swann RedAlert SW242-WDW Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario

DSC

DSC PC 4010 Manual del propietario