Supero Supero SAS-825TQ Manual de usuario

Rev. 2.0

SAS-825TQ Backplane

USER'S GUIDE

BAR CODE

REV 2.0

SAS825TQ

GNDGND+12V +5VGNDGND+12V +5V

I C

ACT_IN

JP29:9072 RESET

I C

SIDEBAND #2

SIDEBAND #1

GNDGND+12V +5VGNDGND+12V +5V

BAR CODE

REV 2.0

SAS825TQ

I C

ACT_IN

JP29:9072 RESET

I C

SIDEBAND #2

SIDEBAND #1

SUPER ®

SAS-825TQ Backplane User’s Guide

Manual Revision 2.0

Release Date: June 10, 2013

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and

documentation, is the property of Supermicro and/or its licensors, and is supplied only under a

license. Any use or reproduction of this product is not allowed, except as expressly permitted by

the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

Preface

iii

Table of Contents

Contacting Supermicro.......................................................................................iv

Returning Merchandise for Service.....................................................................v

Chapter 1 SAS-825TQ Safety Guidelines

1-1 ESD Safety Guidelines ................................................................................... 1-1

1-2 General Safety Guidelines .............................................................................. 1-1

1-3 An Important Note to Users ............................................................................ 1-2

1-4 Introduction to the SAS-825TQ Backplane..................................................... 1-2

Chapter 2 Connectors, Jumpers and Pin Denitions

2-1 Front Connectors and SAS Ports ................................................................... 2-1

Front Connectors ............................................................................................ 2-1

SAS Ports........................................................................................................ 2-1

2-2 FrontConnectorandPinDenitions............................................................... 2-2

2-3 FrontJumperLocationsandPinDenitions................................................... 2-4

Explanation of Jumpers .................................................................................. 2-4

SGPIO and I2C Modes and Jumper Settings ................................................. 2-5

SAS Port Connections in I2C and SGPIO Settings ....................................... 2-7

Front LED Indicators ....................................................................................... 2-7

2-4 Rear Connectors and LED Indicators............................................................. 2-8

SAS-825TQ Backplane User’s Guide

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 23511

Taiwan (R.O.C)

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3992

Web Site: www.supermicro.com.tw

Technical Support:

Email: [email protected]

Tel: +886-(2)-8226-3990

Preface

Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required be-

fore any warranty service will be rendered. You can obtain service by calling your

vendor for a Returned Merchandise Authorization (RMA) number. When returning

to the manufacturer, the RMA number should be prominently displayed on the

outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and

handling charges will be applied for all orders that must be mailed when service

is complete.

For faster service, RMA authorizations may be requested online (http://www.super-

micro.com/support/rma/).

Whenever possible, repack the backplane in the original Supermicro box, using the

original packaging materials. If these are no longer available, be sure to pack the

backplane in an anti-static bag and inside the box. Make sure that there is enough

packaging material surrounding the backplane so that it does not become damaged

during shipping.

This warranty only covers normal consumer use and does not cover damages in-

curred in shipping or from failure due to the alteration, misuse, abuse or improper

maintenance of products.

Duringthewarrantyperiod,contactyourdistributorrstforanyproductproblems.

SAS-825TQ Backplane User’s Guide

Notes

1-1

Chapter 1: Safety Guidelines

Chapter 1

SAS-825TQ Safety Guidelines

To avoid personal injury and property damage, carefully follow all the safety steps

listed below when accessing your system or handling the components.

1-1 ESD Safety Guidelines

Electrostatic Discharge (ESD) can damage electronic components. To prevent dam-

age to your system, it is important to handle it very carefully. The following measures

are generally sufcient to protect your equipment from ESD.

•Use a grounded wrist strap designed to prevent static discharge.

•Touch a grounded metal object before removing a component from the antistatic

bag.

•Handle the backplane by its edges only; do not touch its components, peripheral

chips, memory modules or gold contacts.

•When handling chips or modules, avoid touching their pins.

•Put the card and peripherals back into their antistatic bags when not in use.

1-2 General Safety Guidelines

•Always disconnect power cables before installing or removing any components

from the computer, including the SAS-825TQ backplane.

•Disconnect the power cable before installing or removing any cables from the

SAS-825TQ backplane.

•Make sure that the SAS-825TQ backplane is securely and properly installed on

the motherboard to prevent damage to the system due to power shortage.

1-2

SAS-825TQ Backplane User's Guide

1-3 An Important Note to Users

All images and layouts shown in this user's guide are based upon the latest PCB

Revision available at the time of publishing. The card you have received may or

may not look exactly the same as the graphics shown in this manual.

1-4 Introduction to the SAS-825TQ Backplane

The SAS-825TQ backplane has been designed to utilize the most up-to-date tech-

nology available, providing your system with reliable, high-quality performance.

ThismanualreectsSAS-825TQRevision2.0,themostcurrentreleaseavailableat

the time of publication. Always refer to the Supermicro Web site at www.supermicro.

comforthelatestupdates,compatiblepartsandsupportedcongurations.

2-1

Chapter 2: Safety Guidelines

BAR CODE

REV 2.0

SAS825TQ

GNDGND+12V +5VGNDGND+12V +5V

I C

ACT_IN

JP29:9072 RESET

I C

SIDEBAND #2

SIDEBAND #1

GNDGND+12V +5VGNDGND+12V +5V

BAR CODE

REV 2.0

SAS825TQ

I C

ACT_IN

JP29:9072 RESET

I C

SIDEBAND #2

SIDEBAND #1

BAR CODE

REV 2.0

SAS825TQ

GNDGND+12V +5VGNDGND+12V +5V

I C

ACT_IN

JP29:9072 RESET

I C

SIDEBAND #2

SIDEBAND #1

GNDGND+12V +5VGNDGND+12V +5V

BAR CODE

REV 2.0

SAS825TQ

I C

ACT_IN

JP29:9072 RESET

I C

SIDEBAND #2

SIDEBAND #1

Chapter 2

Connectors,JumpersandPinDenitions

2-1 Front Connectors and SAS Ports

Front Connectors SAS Ports

Figure 2-1: Front Connectors

Figure 2-2: Front SAS Ports

1. 4-pin power connector: JP13

2. 4-pin power connector: JP10

3. CD-ROM/oppyconnector:JP18

4. CD-ROM/oppyconnector:JP17

5. SAS activity LED header: JP26

6. I2C connector #2: JP45

7. I2C connector #1: JP44

8. Sideband connector #2: JP52

9. Sideband connector #1: JP51

10. MG9072 chip

11. Upgrade header: JP46

12. SAS Port #0

13. SAS Port #1

14. SAS Port #2

15. SAS Port #3

16. SAS Port #4

17. SAS Port #5

18. SAS Port #6

19. SAS Port #7

2-2

SAS-825TQ Backplane User's Guide

Backplane

Main Power

4-Pin Connector

Pin#Denition

1+12V

2 and 3 Ground

4 +5V

CD-ROM/FDD Power

4-Pin Connector

Pin#Denition

1+5V

2 and 3 Ground

4 +12V

#1 and #2 Backplane Main Power Connec-

tors

The 4-pin connectors, designated JP10, and

JP13 provide power to the backplane. See

thetableontherightforpindenitions.

#3 and #4 CD-ROM/Floppy Pin Connectors

Pin connectors designated J17 and J18,

provide power to the CD-ROM and oppy

drives. See the table on the right for pin

denitions.

2-2 FrontConnectorandPinDenitions

SAS Activity LED Header

PinDenitions

Pin#Denition Pin#Denition

1 ACT IN#0 6 ACT IN#4

2 ACT IN#1 7 ACT IN#5

3 ACT IN#2 8 ACT IN#6

4 ACT IN#3 9 ACT IN#7

5 Ground 10 Empty

#5 Activity LED Headers

The activity LED header, designated JP26

is used to indicate the activity status of

each SAS drive. The activity LED header is

located on the front panel. For the activity

lead header to work properly, connect to it

using a 10-pin LED cable. This is only used

when the activity LED is not supported by

the hard drive.

#6 and #7 I2C Connectors

The I2C Connectors, designated JP44 and

JP45, are used to monitor the HDD activity

and status. See the table on the right for pin

denitions.

I2C Connector

PinDenitions

Pin#Denition

1 Data

2 Ground

3 Clock

4 No Connection

Tabla de contenidos

Otros manuales de Hardware de computadora de Supero

Supero

Supero Supero SAS 815TQ Manual de usuario

Supero

Supero X10DGO-T Manual de usuario

Supero

Supero SAS-837A BACKPLANE Manual de usuario

Supero

Supero AOC-SIM1U Add-on Card Manual de usuario

Supero

Supero AOC-SIMLC Manual de usuario

Supero

Supero AOC-CGP-i2 Manual de usuario

Supero

Supero AOC-USAS-L4i Manual de usuario

Supero

Supero AOC-SIMLC-HTC Manual de usuario

Supero

Supero Supero SAS-846EL Manual de usuario

Supero

Supero Supero SAS-826A Manual de usuario

Supero

Supero AOC-USAS-S4ir Manual de usuario

Supero

Supero SAS 933TQ Manual de usuario

Supero

Supero Supero BPN-SAS-823TQ Manual de usuario

Supero

Supero SAS-216EL1/EL2 Manual de usuario

Supero

Supero BPN-SAS2-216EL1 Manual de usuario

Supero

Supero SAS-747TQ BACKPLANE Manual de usuario

Supero

Supero BPN-EXP-847DR1EL1 Manual de usuario

Supero

Supero AOC-SGP-i4 Manual de usuario

Supero

Supero CSE-SATA-813L Manual de usuario

Supero

Supero AOC-SIMSO+ Manual de usuario

Supero

Supero SAS 808TQ Manual de usuario

Supero

Supero CSE-PTJBOD-CB3 Manual de usuario

Supero

Supero Supero SAS 846 TQ BACKPLANE Manual de usuario

Supero

Supero BPN-SAS2-847DR Backplane Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario