Supero AOC-SIMSO+ Manual de usuario

SUPER

Rev. 1.1c

USER'S GUIDE

AOC-SIMSO/SIMSO+

AOC-SIMSO/SIMSO+ User's Guide

1-2

The information in this User’s Guide has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this user's guide, or to notify

any person or organization of the updates.

Please Note: For the most up-to-date version of this user's guide, please see our

web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in this

user's guide at any time and without notice. This product, including software, if any, and documenta-

tion may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any

medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all

claims will not exceed the price paid for the hardware product.

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Unless you request and receive written permission from SUPER MICRO COMPUTER, Inc., you

may not copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

User's guide Revision: Rev. 1.1c

Release Date: July 17, 2012

1-3

Chapter 1: Introduction

Table of Contents

Chapter I: Introduction.............................................................................1-4

1.1 Overview.................................................................................................... 1-4

1.2 IPMI Version 2.0 ........................................................................................ 1-5

1.3 Product Features ...................................................................................... 1-5

1.4 Checklist ................................................................................................... 1-5

1.5 An Important Note to the User................................................................ 1-5

1.6 Contacting Supermicro............................................................................ 1-6

Chapter 2: Technical Specications and Hardware Installation.......... 2-1

2.1 The Conguration of the AOC-SIMSO/SIMSO+ & the AOC-USB2RJ45....

......................................................................................................................... 2-1

2.2 AOC-SIMSO/SIMSO+ Connector and Jumper Locations .................... 2-2

2.2.1 Front Components on the AOC-SIMSO(+).............................................. 2-2

2.2.2 The Dedicated LAN LED on the AOC-USB2RJ45.................................. 2-2

 2.2.3ConnectorDescriptionsandPinDenitions............................................ 2-3

 2.2.4LEDDescriptionsandPinDenitions ..................................................... 2-4

2.2.5 Rear Components on the AOC-SIMSO(+) .............................................. 2-5

2.3 Block Diagram .......................................................................................... 2-6

2.4 Installing the AOC-SIMSO(+) ................................................................... 2-7

2.4.1 Safety Guidelines .................................................................................... 2-7

2.4.2 SIMSO Slot Locations ............................................................................. 2-8

Chapter 3: Software Application and Usage ..........................................3-1

3.1 Home Page ................................................................................................ 3-3

3.2 Functions Listed On the Home Page ..................................................... 3-5

3.2.1 Remote Control ....................................................................................... 3-5

3.2.2 Virtual Media............................................................................................ 3-7

3.2.3 System Health ........................................................................................3-11

3.2.4 User Management ................................................................................. 3-17

3.2.5 KVM Settings......................................................................................... 3-21

3.2.6 Device Settings...................................................................................... 3-25

3.2.7 Maintenance .......................................................................................... 3-38

3.3 Remote Console Main Page .................................................................. 3-42

3.3.1 Remote Console Options ...................................................................... 3-43

Chapter 4: Frequently Asked Questions ................................................4-1

AOC-SIMSO/SIMSO+ User's Guide

1-4

Chapter 1

Introduction

This user's guide is written for system integrators, PC technicians and

knowledgeable PC users who intend to integrate Supermicro's unique IPMI 2.0

Management Utility with support of KVM-over-LAN (*) into their systems. It pro-

vides detailed information for the application and use of the AOC-SIMSO/SIMSO+

that supports remote access for system monitoring, diagnosis and management.

With the most advanced technologies built-in, the AOC-SIMSO/SIMSO+ offers a

complete,efcient,andcost-effectiveremoteservermanagement. 

(Note: KVM-over-LAN is only for the AOC-SIMSO+ only.)

1.1 Overview

TheAOC-SIMSO/SIMSO+isahighlyefcient,highlycompatibleandeasy-to-use

IPMI card that allows the user to take advantage of the BMC, a baseboard man-

agement controller installed on a server motherboard and the IPMIView, an IPMI-

compliant management application software loaded in a PC, to provide serial links

between the main processor and other system components, allowing for network

interfacing via remote access. With an independent Raritan KIRA100 processor

built-in, the AOC-SIMSO/SIMSO+ provides the user with a solution to ease the

complex and expensive systems, allowing an administrator to access, monitor,

diagnose and manage network interfacing anywhere, anytime.

1.2 IPMI Version 2.0

The AOC-SIMSO/SIMSO+ supports the functionality of IPMI Version 2.0. The key

features include the following:

• Supports IPMI 2.0

• Supports Serial over LAN

• Supports KVM over LAN (For the AOC-SIMSO+ only)

• Supports LAN Alerting-SNMP Trap

• Supports Event Log

• Offers OS (Operating System) Independency

• Provides remote Hardware Health Monitoring via IPMI. Key features include

the following:

• Temperature monitoring

• Fan speed monitoring

• Voltage monitoring

• Power status monitoring, chassis intrusion monitoring

• Remote power control to power-on, power-off or reboot a system

1-5

Chapter 1: Introduction

• Remote access to text-based, graphic-based system information,

includingBIOScongurationsandOSoperationinformation(KVM)

• Remote management of utility/software applications

• Provides Network Management Security via remote access/console redirec-

tion. Key features include:

• User authentication enhancement

• Encryptionsupportenhancement,allowingforpasswordcongura-

tion security to protect sensitive data transferring via Serial over

LAN

• Supports the following Management tools: IPMIView, CLI (Command Line

Interface)

• Supports RMCP & RMCP protocols

1.3 Product Features

(a) The AOC-SIMSO/SIMSO+ Series: (IPMI 2.0 with a Dedicated

LAN)

• Minisize(2.65"Wx1.75"H)(67.31mmWx44.45mmH)

• SupportsIPMIoverLAN

• Supports1Uandabove

• SupportsdedicatedLAN

1.4 Checklist

If your shipping package came with missing or damaged parts, please contact

Supermicro's Tech. Support. Please refer to the following checklist when

contacting us.

i. AOC-SIMSO/SIMSO+:

ii. The SKT-0240L Kit (The SKT-0240L kit is included in the AOC-SIMSO+ shipping

packageOnly.TheSKT-0240Lkitcontainsfull-sizeandlowproleI/Obackplates,

a USB2RJ45 add-on card, and a CBL-0165L cable.)

iii. CDR-SIMIPMI: One Installation CD

iv. White Box with Correct Barcode Label (showing AOC-SIMSO/SIMSO+).

1.5 An Important Note to the User

The graphics shown in this user's guide were based on the latest PCB Revision

available at the time of publishing of this guide. The SIMSO/SIMSO+ card you’ve

received may or may not look exactly the same as the graphics shown in this

user's guide.

AOC-SIMSO/SIMSO+ User's Guide

1-6

1.6 Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Informaion)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Pacic

Address: SuperMicro, Taiwan

4F, No. 232-1 Liancheng Road

Chung-Ho Dist., New Taipei City 235

Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Web Site: www.supermicro.com.tw

Email: [email protected] (Technical Support)

Tel: +886-(2) 8226-5990 (Technical Support)

2-1

Chapter 2: Technical Specications and Installation

Chapter 2

Technical Specications and Hardware

Installation

2.1 Conguring the AOC-SIMSO/SIMSO+ and the AOC-

USB2RJ45 Add-On Cards

The AOC-SIMSO/SIMSO+ Add-On Card is connected to a Dedicated LAN Ethernet

port located on the AOC-USB2RJ45 Add-On Card via an SMC Proprietary cable

(CBL-0165L) for External LAN access. One end of the CBL-0165L cable is con-

nected to the mini USB connector (J1) located on the AOC-SIMSO(+) card and the

other end to that of the AOC-USB2RJ45 card. There are two LEDs located on the

LAN port to indicate network links and activities. Refer to the picture below for the

conguration.

Note 1: You can also use LAN1 on the motherboard if you do not need the dedicated

LAN support. However, dedicated LAN is recommended for better graphic support

when the KVM feature is used.

Note 2: For dedicated LAN to work properly, Cable CBL-177L is required for a moth-

erboard with a SIMSO IPMI module that is located far from the back plate of the

chassis.Refertothemotherboardspecications on our website. (The CBL-177L

cable is to be purchased separately from Supermicro.)

Note 3:TheSKT-0240Lkitcontainsfull-sizeandlowproleI/Obackplates,aUSB

2RJ45 add-on card, and a CBL-0165L cable The SKT-0240L Kit is included in the

SIMSO+ shipping package only.

AOC-SIMSO(+)

CBL-0165L Cable, or

CBL-0177L Cable* (See

Note 2 above.)

AOC-USB2RJ45

Dedicated

Ethernet

(LAN) Port

Mini USB

Connector (J1)

Mini USB

Connector

(J1)

Bracket

LAN LEDs

The SKT-0240L Kit

AOC-SIMSO/SIMSO+ User's Guide

2-2

2.2 AOC-SIMSO/SIMSO+ Connector and Jumper

Locations

Front View

2.2.1 Front Components on the AOC-SIMSO(+)

1. Raritan's Kira 100 RISC System on Chip

2. Firmware with Linux System & Boot ROM

3. Transformer

4. SDRAM (128Mb/133MHz)

5. J1: Mini USB 9-pin Connector (Note)

6. JBT1: Kira 100 Processor Reset (Note)

7. D1: Heartbeat Activity LED Indicator (Note)

2.2.2 The Dedicated LAN LED Indicators on the AOC-USB2RJ45

8. LAN LEDs (Note)

(Note: See Pg. 2-3, 2-4 for details)

2-3

Chapter 2: Technical Specications and Installation

#5 (J1) Mini Universal Serial Bus (USB)

Connector

There is a mini USB connector (J1) located on the

AOC-SIMSO/SIMSO+ and another mini USB con-

nector is located on the AOC-USB2RJ45. Use Cable

CBL-0165L or CBL-0177L (*) to connect the two mini

USB connectors on both add-on cards for external

LAN access. Refer to Page 2-1 for details. See the

tableatrightforthepindenitions.

Refer to Note 2 on Page 2-1.

2.2.3 Connector Descriptions and Pin Denitions

Mini USB

Connector

AOC-USB2RJ45

Mini USB Pin Denitions

(J1)

Pin#Denition

1 Eth-TX_H

2 Eth-TX_L

3 Phy-100

4 Eth-RX_L

5 Eth-RX_H

6 Phy-ACT

7 Det.icated LAN-

Detected

8 3V-duall

9 Ground

#6 (JBT1) RISC CPU Reset

JBT1 is used to reset the Kira 100 Processor, NIC,

UART, USB and R.T. Instead of pins, this "jumper"

consists of contact pads to prevent the accidental

reset. Use a metal object such as a small screwdriver

to touch both pads at the same time to short the

connection. After a reset or AC power-on, the AOC-

SIMSO(+) will automatically detect if a CBL-0165L

cable is connected. If a cable is not detected, the

AOC-SIMSO(+) will transfer the "Remote Control"

Function to LAN1 on the motherboard. If a cable is

detected, the AOC-SIMSO(+) will use the dedicated

LAN on the card to manage motherboard activities

via Remote Console.

(Note: The SKT-0240L is included in the SIMSO+

shipping package.)

AOC-SIMSO(+)

CBL-0165L Cable or

CBL-0177L Cable* (See

Note 2 on Page 2-1)

The SKT-0240L (Note Below)

AOC-SIMSO/SIMSO+ User's Guide

2-4

Link LED

2.2.4 LED Descriptions and Pin Denitions

#7 (D1) Heartbeat LED Indicator

Heartbeat LED (D1), located on the front

side of the AOC-SIMSO(+) card, indicates

the functionality and activity of the add-on

card. The blinking of the Heartbeat LED

indicates that the AOC-SIMSO(+) is ac-

tive. However, when the Linux OS and

the drivers are being loaded after each

AC power-on or reset, the Heartbeat

LED is off for about a minute. Then, the

Heartbeat LED will be on again to indicate

that the AOC-SIMSO(+) is active. See the

table on the right for details.

Heartbeat LED (D1)

On (Blinking) SIMSO(+): active

Off (for 1

minute)

Loading Firmware

Off (Continu-

ously)

SIMSO is not active

Activity

LED

GLAN Link Indicator

LEDColorDenition

Off No Connection or 10 Mbps

Green 100 Mbps

GLAN Activity Indicator

ColorStatusDenition

Amber Flashing Active

#8 Dedicated LAN LED Indicators

There are two LAN LED Indicators located

on the (Dedicated) LAN port on the AOC-

USB2RJ45 Add-On Card. The green LED

indicates activity, while the power LED

may be green or off to indicate the speed

of the Ethernet connection. See the tables

on the right for more information.

Tabla de contenidos

Otros manuales de Hardware de computadora de Supero

Supero

Supero SAS-747TQ BACKPLANE Manual de usuario

Supero

Supero AOC-CGP-i2 Manual de usuario

Supero

Supero Supero BPN-SAS-823TQ Manual de usuario

Supero

Supero SAS 808TQ Manual de usuario

Supero

Supero SAS 822TQ BACKPLANE Manual de usuario

Supero

Supero SAS 828TQ BACKPLANE Manual de usuario

Supero

Supero Supero SAS-846A Manual de usuario

Supero

Supero SAS-837A BACKPLANE Manual de usuario

Supero

Supero BPN-SAS2-847DR Backplane Manual de usuario

Supero

Supero SAS2-836EL Manual de usuario

Supero

Supero Supero SAS 846 TQ BACKPLANE Manual de usuario

Supero

Supero BPN-SAS3-217HD Backplane Manual de usuario

Supero

Supero SAS-827B Manual de usuario

Supero

Supero SAS-216EL1/EL2 Manual de usuario

Supero

Supero BPN-EXP-847DR1EL1 Manual de usuario

Supero

Supero X10DGO-T Manual de usuario

Supero

Supero Supero SMT IPMI Manual de usuario

Supero

Supero Supero SAS-826A Manual de usuario

Supero

Supero Supero SAS-836TQ Manual de usuario

Supero

Supero Supero SAS-825TQ Manual de usuario

Supero

Supero AOC-USAS-L4i Manual de usuario

Supero

Supero AOC-USAS-S4ir Manual de usuario

Supero

Supero SAS 933TQ Manual de usuario

Supero

Supero BPN-SAS2-216EL1 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario