SunSynk SYNK-5K-SG03LP1 Guía del usuario
INSTALLER MANUAL
SYNK-3.6K-SG03LP1
SYNK-5K-SG03LP1
www.sunsynk.com
SINGLE-PHASE
HYBRID INVERTER
v.35 (12/11/23) PLEASE RETAIN FOR
FUTURE REFERENCE
SINGLE PHASE HI 3.6/5kW | Installer Manual2
Table of Contents
SAFETY 3
General Safety 3
Symbols/Safety Signs 3
Safety Instructions 5
Product Disposal 5
PRODUCT INTRODUCTION 6
Product Overview 6
Product Size 7
Product Features 8
Basic System Architecture 9
TECHNICAL SPECIFICATIONS 10
INSTALLATION 12
Parts List 12
Selecting the Mounting Area 13
Mounting the Inverter 14
Battery Connection 15
Function Port Denition 17
Recommended DC Battery Protection 18
Connecting a Lithium Battery 18
Lead-Acid Battery Temperature Sensor 20
Connecting the AC 21
Recommended AC Surge Protector 22
PV Connection 23
PV Module Selection 23
PV Module Wiring 23
PV Protection 24
Installing the CT Coil 24
Meter Connection 26
System Connection for the CHNT Meter 26
Earth Connection (MANDATORY) 26
Wiring System for Inverter 27
Typical Application of Diesel Generator 28
Single-Phase Parallel Connection 29
Three-Phase Parallel Inverter 30
OPERATION 31
Switching ON/OFF 31
Display 31
LED Indicators 31
Function Buttons 31
LCD Operation Flow Chart 32
Home Page 33
Status Page 33
System Flow Page 34
Setup Page 35
Basic Setup 36
Set Time (Clock) 36
Set Company Name / Beeper / Auto dim 36
Factory Reset and Lock Code 37
Inverter Remote Control 38
Battery Setup Page 38
Generator & Battery Page 39
Battery Discharge Page 41
Setting Up a Lithium Battery 43
Program Charge & Discharge Times 49
Grid Supply Page 53
Paralleling Inverters Advanced Settings 57
Connecting the DRM’s 60
Advanced Function Setup 61
Solar Power Generated 61
Grid Power 62
Advanced Settings for Wind Turbines 63
Advanced Settings for Auxiliary Load 64
OPERATION MODES 67
Mode I: Basic 67
Mode II: Generator 67
Mode III: With Aux-Load 68
Mode IV: AC Couple 68
Mode V: Grid-Tied 70
FAULT CODES 70
COMMISSIONING 74
Start-Up / Shutdown Procedure 74
Inverter Commissioning Info 74
GDFI Fault 75
MAINTENANCE 75
APPENDIX A 76
APPENDIX B 77
APPENDIX C 77
APPENDIX D 77
APPENDIX E 77
SINGLE PHASE HI 3.6/5kW | Installer Manual3
SAFETY
This device should only be used in accordance with the instructions within this manual and in compli-
ance with local, regional, and national laws and regulations. Only allow this device to be installed, oper-
ated, maintained, and repaired by other people who have read and understood this manual. Ensure the
manual is included with this device should it be passed to a third party.
DO NOT allow minors, untrained personnel, or person(s) suering from a physical or mental impairment
that would aect their ability to follow this manual, install, maintain or repair this device.
Any untrained personnel who might get near this device while it is in operation MUST be informed that it
is dangerous and instructed carefully on how to avoid injury.
General Safety
Symbols/Safety Signs
This symbol indicates information that if
ignored, could result in personal injury,
physical damage or even death due to
incorrect handling.
CE mark is attached to the solar
inverter to verify that the unit follows
the provisions of the European Low
Voltage and EMC Directives.
Risk of burn. Refer to the operating instructions.
5min
Risk of electric shock.
DO NOT touch the terminal or remove
the shell within 5 minutes after discon-
necting all power.
The UKCA marking is used for products
placed on the market in Great Britain
(England, Scotland and Wales). The
UKCA marking applies to most prod-
ucts for which the CE marking could be
used.
Keep the equipment well-ventilated.
ONLY qualied personnel should install
or perform maintenance work on the
units.
This product's batteries contain an ex-
plosive, self-reactive material that could
blow up when heated.
Warranty Void if Seal is Broken
Be careful when touching the inverter!
It is an electrical product with risk of
electric shock and heating.
Store below 25°C.
Indicates that this product is recyclable. Keep the product out of reach of chil-
dren!
Keep away from open ames and
moisture.
Avoid unsuitable shoes for installing
and operating the inverter.
SINGLE PHASE HI 3.6/5kW | Installer Manual4
V DC 48 V
230V
15.70 A
BATTERY INPUT
Battery Discharge Voltage, Battery
Discharge Current, Input Voltage Type,
Battery Discharge Power.
V DC 48 V
230V
15.70 A
AC OUTPUT
Output Voltage, Input Voltage Type, Ac
Output Rated Current, Max AC Current,
Output Frequency, Max AC ISC, Power
Factor & AC Output Rated Power.
V DC 48 V
230V
15.70 A
TEMPERATURE
Ambient, Min & Max.
V DC 48 V
230V
15.70 A
PV INPUT
PV Input Voltage, Number of MPPT's,
MPPT Input Current & Max PV ISC.
V DC 48 V
230V
15.70 A
Net Weight in Kilograms.
V DC 48 V
230V
15.70 A
Protective Conductor Terminal or Earth
Ground Terminal.
V DC 48 V
230V
15.70 A
Single Phase.
V DC 48 V
230V
15.70 A
Three Phase.
V DC 48 V
230V
15.70 A
Inverter DC to AC.
WARRANTY REGISTRATION
Scan the QR code to access our web-
site and sign up for the manufacturer’s
warranty.
MANUAL DOWNLOAD
Download the latest version of the
instruction manual by scanning the QR
code.
Do not dispose the device, accesso-
ries, and packaging with regular waste.
Follow local ordinances or contact the
manufacturer for disposal guidance.
V DC 48 V
230V
15.70 A
CONTINUOUS OUTPUT
CURRENT
Maximum Continuous Output Current,
Output Frequency and Voltage, & AUX
(programmable AC output on battery
SOC).
3
SINGLE PHASE HI 3.6/5kW | Installer Manual5
Safety Instructions
This chapter contains important safety and operating instructions. Read and keep this manual for future
reference.
Before using the inverter, please read the instructions and warning signs of the battery and correspond-
ing sections in the instruction manual.
Do not disassemble the inverter. If you need maintenance or repair, take it to a professional service
center.
Improper reassembly may result in electric shock or re.
To reduce the risk of electric shock, disconnect all wires before attempting any maintenance or cleaning.
Turning o the unit will not reduce this risk.
Never charge a frozen battery.
For optimum operation of this inverter, please follow the required specications to select the appropri-
ate cable size. It is very important to operate this inverter correctly.
Be very cautious when working with metal tools on or around batteries. Dropping a tool may cause a
spark or short circuit in batteries or other electrical parts, even causing an explosion.
Please strictly follow the installation procedure when you want to disconnect AC or DC terminals.
Please refer to this manual's "Installation" section for details.
Grounding instructions - this inverter should be connected to a permanent grounded wiring system. Be
sure to comply with local requirements and regulations to install this inverter.
Never cause AC output and DC input to short-circuit. Do not connect to the mains when DC input short
circuits.
Product Disposal
DO NOT dispose this product with domestic waste!
Electrical devices should be disposed of in accordance with regional directives on electronic and/ or elec-
tronic-waste disposal. In case of further questions, please consult your supplier. In some cases, the supplier
can take care of proper disposal.
WARNING
HIGH LIFE RISK DUE TO FIRE OR ELECTROCUTION.
Sunsynk Single-Phase Hybrid Inverter can only be installed by a qualied licensed electrical
contractor. This is not a DIY product.
SINGLE PHASE HI 3.6/5kW | Installer Manual6
PRODUCT INTRODUCTION
This multifunctional inverter combines the functions of an inverter, solar charger and battery charger to oer
uninterruptible power support with a portable size. Its comprehensive LCD display oers user-congurable
and easily accessible button operations such as battery charging, AC/solar charging, and acceptable input
voltage based on dierent applications.
Product Overview
1. Inverter Indicators 7. DRMs Port 13. Power On/O Button
2. LCD Display 8. Parallel Port 14. DC Switch
3. Function Buttons 9. Function Port 15. PV Input with Two MPPT
4. Battery Input Connectors 10. Generator Input 16. Battery
5. RS485/Meter Port 11. Load 17. Temperature Sensor
6. BMS 485/CAN Port 12. Grid 18. Wi-Fi Interface
��
1 2
1
2
5
9
10
11
12
7
6
3
4
8
13
14
15
16
17
18
SINGLE PHASE HI 3.6/5kW | Installer Manual7
Product Size
Inverter Size
SINGLE PHASE HI 3.6/5kW | Installer Manual8
Product Features
INTERACTIVE
Easy and simple to understand display
Supporting Wi-Fi or GSM monitoring
Visual power ow screen
Smart settable 3-stage MPPT charging for optimized battery performance
Auxiliary load function
Parallel / multi invert function grid-tied and o-grid
COMPATIBLE
Compatible with main electrical grid voltages or power generators
Compatible with wind turbines
220V single phase, pure sine-wave inverter
Self-consumption and feed-in to the grid
Auto restart while AC is recovering
Auto earth bond feature (Via a relay)
CONFIGURABLE
Fully programmable controller
Programmable supply priority for battery or grid
Programmable multiple operation modes: on-grid/o-grid & UPS
Congurable battery charging - current/voltage based on applications by LCD setting
Congurable AC / solar / generator charger priority by LCD setting
SECURE
Overload/over-temperature/short-circuit protection
Smart battery charger design for optimized battery protection
Limiting function installed to prevent excess power overow to grid
APPLICATIONS
Marine (vessel power management)
Power shedding (home/oce/factory)
UPS (fuel-saving systems)
Remote locations with solar and wind generators
Building sites
Military locations
Telecommunication
SINGLE PHASE HI 3.6/5kW | Installer Manual9
Basic System Architecture
The following illustration shows the basic application of this inverter.
It also includes the following devices to have a Complete running system.
Generator or Utility
PV modules
Consult with your system integrator for other possible system architectures depending on your
requirements.
This inverter can power all kinds of appliances in a home or one environment, including motor-type
appliances such as refrigerators and air conditioners
SINGLE PHASE HI 3.6/5kW | Installer Manual10
TECHNICAL SPECIFICATIONS
Model SYNK-3.6K-SG03LP1 SYNK-5K-SG03LP1
Battery Input Date
Battery Type Lead-acid or Li-Ion
Battery Voltage Range 48Vd.c (40Vd.c ~ 60Vd.c)
Max. Charging/Discharging Current 90Ad.c (max.) 120Ad.c (max.)
Charging Curve 3 Stages / Equalization
External Temperature Sensor Yes
Charging Strategy for Li-Ion Battery Self-adaption to BMS
PV String Input Data
Max. DC Input Power 4680W 6500W
PV Input Voltage 370V (125V~500V)
MPPT Range 150~425V
Full Load DC Voltage Range 300~425V
Start-up Voltage 125V
PV Input Current 13Ad.c + 13Ad.c
No. of MPPT Trackers 2
No. of Strings Per MPPT Tracker 1+1
AC Output Data
Rated AC Output and UPS Power 3600W 5000W
Max. AC Output Power 3960W 5500W
Max. AC Output Apparent Power 3960VA 5500VA
Peak Power(o grid) 2 times of rated power, 10s
AC Output Rated Current 16.4/15.7Aa.c 22.7/21.7Aa.c
Max. AC Current 18/17.2Aa.c 25/23.9Aa.c
Max. Continuous AC Passthrough 35A
Power Factor 0.8 leading to 0.8 lagging
Output Frequency and Voltage 50/60Hz; 220/230 (single phase)
Grid Type Single Phase
Total Harmonic Distortion (THD) <3% (of nominal power)
DC current injection <0.5% ln
Eciency
Max. Eciency 97.60%
Euro Eciency 96.50%
MPPT Eciency >99%
Protection
PV Input Lightning Protection Integrated
Anti-islanding Protection Integrated
PV String Input Reverse Polarity
Protection Integrated
Insulation Resistor Detection Integrated
Residual Current Monitoring Unit Integrated
Output Over Current Protection Integrated
Output Shorted Protection Integrated
Surge Protection DC Type II / AC Type II
Over Voltage Category DC Type II / AC Type III
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Inversor de SunSynk
SunSynk
SunSynk ECCO SUN-3K-SG04LP1-24-EU Manual de usuario
SunSynk
SunSynk SUN300G3-EU-230 Manual de instrucciones
SunSynk
SunSynk LIFELYNK X SM3.6kWLL Manual de usuario
SunSynk
SunSynk SYNK-8K-SG04LP3 Guía del usuario
SunSynk
SunSynk SUN-8K-SG04LP3 Guía del usuario
SunSynk
SunSynk SUNSYNK-8K-SG01LP1 Manual de usuario
SunSynk
SunSynk SUN-8K-SG04LP3 Manual de usuario
SunSynk
SunSynk ECCO SUN-3K-SG04LP1-24-EU Manual de usuario
SunSynk
SunSynk SUNSYNK-3K-SG04LP1 Guía del usuario
SunSynk
SunSynk SUNSYNK MAX Manual de usuario
SunSynk
SunSynk LIFELYNK ALL-IN-ONE Guía del usuario
SunSynk
SunSynk SUNSYNK-25K-SG01HP3-EU-BM2 Manual de usuario
SunSynk
SunSynk LoadShedder SM2.5kWLS Manual de usuario
SunSynk
SunSynk 8K-SG04LP3 Guía del usuario
SunSynk
SunSynk ECCO SUN-5K-SG05LP1-EU Manual de usuario
SunSynk
SunSynk SYNK-8K-SG04LP3 Guía del usuario
SunSynk
SunSynk SYNK-3.6K-SG04LP1 Manual de usuario
SunSynk
SunSynk SUN-3.6K-SG01/03LP1-EU Guía del usuario
SunSynk
SunSynk Hybrid Parity Guía del usuario
SunSynk
SunSynk SUNSYNK-6K-SG02LP1 Guía del usuario
