SunSynk SYNK-16K-SG01LP1 Guía del usuario

SUNSYNK MAX

INSTALLER MANUAL

v.15 PLEASE RETAIN FOR

FUTURE REFERENCE

SYNK-16K-SG01LP1

www.sunsynk.com

[email protected]

SAFETY 3

General Safety 3

Symbols/Safety Signs 3

Safety Instructions 5

Product Disposal 5

PRODUCT INTRODUCTION 6

Product Overview 6

Product Size 7

Product Features 8

Basic System Architecture 9

TECHNICAL SPECIFICATIONS 10

INSTALLATION 12

Parts List 12

Selecting the Mounting Area 13

Mounting the Inverter 14

Battery Connection 15

Function Port Denition 17

Battery Temperature Sensor Connection 18

Connecting the AC 19

Recommended AC Surge Protector 20

PV Connection 21

PV Module Selection 21

PV Module Wiring 21

PV Protection 22

Installing the CT Coil 23

Earth Connection (MANDATORY) 24

Meter Connection 26

CHiNT Meter 26

Eastron Meter (SDM120CT) 26

Wiring System for Inverter 27

Typical Application of Diesel Generator 28

Single-Phase Parallel Connection 29

Single-Phase Parallel Connection - Diesel

Generator 30

Three-Phase Parallel Inverter 31

OPERATION 32

Switching ON/OFF 32

Display 32

LED Indicators 32

Function Buttons 32

LCD Operation Flow Chart 33

Home Page 34

Status Page 34

System Flow Page 35

Setup Page 36

Basic Setup 37

Set Time (Clock) 37

Set Company Name / Beeper / Auto dim 37

Factory Reset and Lock Code 38

Inverter Remote Control 39

Battery Setup Page 39

Generator & Battery Page 40

Battery Discharge Page 42

Setting Up a Lithium Battery 44

Program Charge & Discharge Times 51

Grid Supply Page 54

Paralleling Inverters Advanced Settings 58

Connecting the DRM’s 61

Advanced Function Setup 62

Solar Power Generated 62

Grid Power 63

Advanced Settings for Wind Turbines 64

Advanced Settings for Auxiliary Load 65

OPERATING MODES 68

Mode I: Basic 68

Mode II: With Generator 68

Mode III: With Aux Load 69

Mode IV: AC Couple 69

FAULT CODES 71

COMMISSIONING 75

Start-Up / Shutdown Procedure 75

Inverter Commissioning Info 75

GDFI Fault 76

MAINTENANCE 76

APPENDIX A 77

APPENDIX B 78

APPENDIX C 78

APPENDIX D 78

APPENDIX E 78

Table of Contents

SUNSYNK MAX | Installer Manual3

SAFETY

This device should only be used in accordance with the instructions within this manual and in compli-

ance with local, regional, and national laws and regulations. Only allow this device to be installed, oper-

ated, maintained, and repaired by other people who have read and understood this manual. Ensure the

manual is included with this device should it be passed to a third party.

DO NOT allow minors, untrained personnel, or person(s) suering from a physical or mental impairment

that would aect their ability to follow this manual, install, maintain or repair this device.

Any untrained personnel who might get near this device while it is in operation MUST be informed that it

is dangerous and instructed carefully on how to avoid injury.

General Safety

Symbols/Safety Signs

This symbol indicates information that if

ignored, could result in personal injury,

physical damage or even death due to

incorrect handling.

CE mark is attached to the solar invert-

er to verify that the unit follows the

provisions of the European Low Voltage

and EMC Directives.

Risk of burn. Keep the equipment well-ventilated.

Risk of electric shock.

DO NOT touch the terminal or remove

the shell within 5 minutes after discon-

necting all power.

The UKCA marking is used for products

placed on the market in Great Britain

(England, Scotland and Wales). The

UKCA marking applies to most prod-

ucts for which the CE marking could be

used.

5min

This product's batteries contain an ex-

plosive, self-reactive material that could

blow up when heated.

Do not disassemble or alter the battery

in any way. Do not strike or puncture

the battery.

The Battery is heavy and can cause inju-

ry if not handled safely.

ONLY qualied personnel should install

or perform maintenance work on the

units.

Be careful when touching the inverter!

It is an electrical product with risk of

electric shock and heating.

Warranty Void if Seal is Broken

Do not place near open re or incin-

erate. Do not use near heaters or hot

temperature sources.

Keep the product out of reach of chil-

dren!

Do not stand on. Avoid unsuitable shoes for installing

and operating the inverter.

Do not step or put any objects onto the

battery.

Do not drop, deform, or impact the

battery.

SUNSYNK MAX | Installer Manual4

1Single Phase. 3Three Phase.

Protective Conductor Terminal or Earth

Ground Terminal. Rechargeable.

Do not submerge the battery in water or

expose it to moisture or liquid Keep out of reach of children, animals,

and insects.

Do not expose the product to sunlight. Inverter DC to AC.

Li-ion Battery. KG Net Weight in Kilograms.

BATTERY INPUT

Battery Discharge Voltage, Battery

Discharge Current, Input Voltage Type,

Battery Discharge Power.

PV INPUT

PV Input Voltage, Number of MPPT's,

MPPT Input Current & Max PV ISC.

Direct Current. Indicates that this product is recyclable.

AC OUTPUT

Output Voltage, Input Voltage Type, Ac

Output Rated Current, Max AC Current,

Output Frequency, Max AC ISC, Power

Factor & AC Output Rated Power.

CONTINUOUS OUTPUT

CURRENT

Maximum Continuous Output Current,

Output Frequency and Voltage, & AUX

(programmable AC output on battery

SOC).

Charging. Discharging.

Follow the indicated temperatures. TEMPERATURE

Ambient, Min & Max.

MANUAL DOWNLOAD

Download the latest version of the

instruction manual by scanning the QR

code.

WARRANTY REGISTRATION

Scan the QR code to access our web-

site and sign up for the manufacturer’s

warranty.

Do not dispose the device, accesso-

ries, and packaging with regular waste.

Follow local ordinances or contact the

manufacturer for disposal guidance.

Refer to the operating instructions.

Contact the supplier within 24 hours if

there is anything wrong. In case of leak-

age contact with eyes or skin, imme-

diately clean with water and seek help

from a doctor.

SUNSYNK MAX | Installer Manual5

Safety Instructions

This chapter contains important safety and operating instructions. Read and keep this manual for future

reference.

Before using the inverter, please read the instructions and warning signs of the battery and correspond-

ing sections in the instruction manual.

Do not disassemble the inverter. If you need maintenance or repair, take it to a professional service

center.

Improper reassembly may result in electric shock or re.

To reduce the risk of electric shock, disconnect all wires before attempting any maintenance or cleaning.

Turning o the unit will not reduce this risk.

Never charge a frozen battery.

For optimum operation of this inverter, please follow the required specications to select the appropri-

ate cable size. It is very important to operate this inverter correctly.

Be very cautious when working with metal tools on or around batteries. Dropping a tool may cause a

spark or short circuit in batteries or other electrical parts, even causing an explosion.

Please strictly follow the installation procedure when you want to disconnect AC or DC terminals.

Please refer to this manual's "Installation" section for details.

Grounding instructions - this inverter should be connected to a permanent grounded wiring system. Be

sure to comply with local requirements and regulations to install this inverter.

Never cause AC output and DC input to short-circuit. Do not connect to the mains when DC input short

circuits.

Product Disposal

DO NOT dispose this product with domestic waste!

Electrical devices should be disposed of in accordance with regional directives on electronic and/ or elec-

tronic-waste disposal. In case of further questions, please consult your supplier. In some cases, the supplier

can take care of proper disposal.

WARNING

HIGH LIFE RISK DUE TO FIRE OR ELECTROCUTION.

Sunsynk Max can only be installed by a qualied licensed electrical contractor. This is not a DIY

product.

SUNSYNK MAX | Installer Manual6

1. Inverter Indicators 6. Modbus (RS-485) Port 11. PV Input

2. LCD Display 7. Parallel Port 12. Generator Input

3. Function Buttons 8. Battery Input Connectors 13. Load

4. DC Switch 9. Function Port 14. Grid

5. Power On/O Button 10. Battery (CANBus) Port 15. WiFi Interface

PRODUCT INTRODUCTION

This multifunctional inverter combines the functions of an inverter, solar charger and battery charger to oer

uninterruptible power support with a portable size. Its comprehensive LCD display oers user-congurable

and easily accessible button operations such as battery charging, AC/solar charging, and acceptable input

voltage based on dierent applications.

Product Overview

SUNSYNK MAX | Installer Manual7

Product Size

Inverter Size

763.00

798.40

859.50

464.00

302.00

490.81

464.00

497.81

10.00

15.00

401.00

200.50

10.00

22. 00

376.00

668.00

282.00

302.00

SUNSYNK MAX | Installer Manual8

Product Features

INTERACTIVE

Supporting WIFI monitoring and 2 strings of each MPP trackers

Smart settable three stages MPPT charging for optimized battery performance.

Visual power ow screen

Time of use function.

Smart Load Function.

Parallel / multi invert function grid-tied and o-grid

COMPATIBLE

Compatible with main electrical grid voltages or power generators

Self-consumption and feed-in to the grid

Auto restart while AC is recovering

CONFIGURABLE

Fully programmable controller

Programmable supply priority for battery or grid

Programmable multiple operation modes: on-grid/o-grid & UPS

Congurable battery charging - current/voltage based on the application

Congurable AC / solar / generator charger priority by LCD setting

SECURE

Overload/over-temperature/short-circuit protection

Smart battery charger design for optimized battery protection

Limiting function installed to prevent excess power overow to grid

SUNSYNK MAX | Installer Manual9

Basic System Architecture

The following illustration shows basic application of this inverter.

It also includes following devices to have a complete running system.

Generator or utility

PV modules

Consult with your system integrator for other possible system architectures depending on your require-

ments.

This inverter can power all kinds of appliances in home or once environment, including motor type applianc-

es such as refrigerator and air conditioner.

SUNSYNK MAX | Installer Manual10

TECHNICAL SPECIFICATIONS

Model SYNK-16K-SG01LP1

Battery Input Data

Battery Type Lead-acid or Lithium-ion

Battery Voltage Range 40~60V

Max. Charge Current 290A

Max. Discharge Current 290A

Charging Curve 3 Stages/Equalization

External Temperature Sensor Yes

Charging Strategy for Li-Ion Battery Self-Adaptation to BMS

PV String Input Data

Max. DC Input Power 20800W

Max PV Input Voltage 370V (125~500V)

MPPT Range 150V~425V

Start-up Voltage 125V

PV Input Current 26A + 26A + 26A

Max. PV Isc 44A + 44A + 44A

No. of MPPT / Strings Per MPPT 3 / 2+2+2

AC Output Data

Max. On-Grid AC Power 16000W

Max. O-Grid AC Power 17600W

Max. AC Output Apparent Power 16000VA

Peak Power (o-grid) 2 times of rated power, 10 S

AC Output Rated Current 72.7/69.6A

Max AC Current 80/76.5A

Max Continuous AC Passthrough 100A

Power Factor 0.8 leading to 0.8 lagging

Output Frequency and Voltage 50Hz/60Hz; 220/230Vac (single phase)

Grid Type Single-Phase

Current Harmonic Distortion THD < 3% (of nominal power)

DC Current Injection < 0.5% In

Eciency

Max. Eciency 97.60%

Euro Eciency 96.50%

MPPT Eciency > 99%

Protection

Integrated

PV Arc Fault Detection, PV Input Lightning Protection, Anti-islanding

Protection, PV String Input Reverse Polarity Protection, Insulation

Resistor Detection, Residual Current Monitoring Unit, Output Over

Current Protection, Output Shorted Protection

Surge Protection DC Type II / AC Type II

Over Voltage Category DC Type II / AC Type III

Tabla de contenidos

Otros manuales de Inversor de SunSynk

SunSynk

SunSynk SUNSYNK-L5.1 Manual de usuario

SunSynk

SunSynk Hybrid Inverter with a Generator Manual de instrucciones

SunSynk

SunSynk SUN-8K-SG04LP3 Guía del usuario

SunSynk

SunSynk SYNK-3.6K-SG04LP1 Manual de usuario

SunSynk

SunSynk ECCO SUN-3.6K-SG05LP1-EU Manual de usuario

SunSynk

SunSynk LoadShedder SM2.5kWLS Manual de usuario

SunSynk

SunSynk 8kW Guía de instalación

SunSynk

SunSynk SUNSYNK MAX Manual de usuario

SunSynk

SunSynk Life3.5Hyb02 Guía del usuario

SunSynk

SunSynk Hybrid Parity Inverter Manual de usuario

SunSynk

SunSynk SUN300G3-EU-230 Manual de instrucciones

SunSynk

SunSynk SUN-25K-SG01HP3-EU-BM2 Guía del usuario

SunSynk

SunSynk ECCO SUN-3K-SG04LP1-24-EU Manual de usuario

SunSynk

SunSynk LIFELYNK ALL-IN-ONE Guía del usuario

SunSynk

SunSynk SYNK-8K-SG04LP3 Guía del usuario

SunSynk

SunSynk SYNK-5K-SG03LP1 Guía del usuario

SunSynk

SunSynk LIFELYNK X SM3.6kWLL Manual de usuario

SunSynk

SunSynk SUNSYNK-8K-SG01LP1 Manual de usuario

SunSynk

SunSynk SUNSYNK-8K-SG01LP1 Guía del usuario

SunSynk

SunSynk Power Bank 1000 Manual de usuario

SunSynk

SunSynk SUN-3.6K-SG01/03LP1-EU Guía del usuario

SunSynk

SunSynk SUNSYNK-3K-SG04LP1 Guía del usuario

SunSynk

SunSynk SUNSYNK-L3.0 Manual de usuario

SunSynk

SunSynk ECCO SUN-5K-SG05LP1-EU Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario