StarTech.com ET10GSFP Manual de usuario

Manual Revision: 11/02/2017

For the latest information, technical specications, and support for

this product, please visit www.StarTech.com/ET10GSFP.

FR: Guide de l’utilisateur - fr.startech.com

DE: Bedienungsanleitung - de.startech.com

ES: Guía del usuario - es.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

IT: Guida per l’uso - it.startech.com

ET10GSFP

10GbE Fiber Media Converter with Open

SFP+ Slot

*actual product may vary from photos

Instruction manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s authority to

operate the equipment.

Industry Canada Statement

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (A)/NMB-3(A)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction manual

Table of Contents

Introduction............................................................................................1

Package contents...................................................................................................................................... 1

Requirements ............................................................................................................................................. 1

Product diagram ....................................................................................2

Front view .................................................................................................................................................... 2

Rear view...................................................................................................................................................... 2

Using the DIP switches..........................................................................3

Install the media converter ..................................................................4

Installing a second SFP card module ..................................................5

Remove a card module from another media converter.............................................................. 5

Install a second SFP card module........................................................................................................ 5

Managing the media converter ...........................................................6

Using the management switches........................................................................................................6

Switch conguration options:.............................................................................................................. 6

Using the serial console command port........................................................................................... 7

Technical support...................................................................................9

Warranty information............................................................................9

Introduction

Package contents

• 1 x 10GbE Ethernet ber media converter

• 1 x universal power adapter

• 4 x power cords (NA/EU/UK/AU)

• 1 x grounding screw

• 1 x quick-start guide

Requirements

• MSA-compliant 10 Gigabit SFP+ transceiver module (Mini-GBIC)

• 10GbE network equipment (for example, a network switch)

• RJ45-terminated UTP Cat6a or better Ethernet cable

• Terminated ber-optic cable (dependent on the SFP+ transceiver module used)

• Available AC electrical outlet

• Terminal emulation software such as PuTTY (if using the serial console port for

management)

Requirements are subject to change. For the latest requirements, please visit

www.StarTech.com/ET10GSFP.

Instruction manual

Product diagram

Front view

Rear view

10Gb RJ45 SFP+ slot LEDs

Management

type switch

Card slot 2

RJ45 LEDs

DC power

input

Slot selection

switch

Card slot 1

DB9 RS232

(serial console

command)

Thumb screw

DIP switches

Instruction manual

Using the DIP switches

Note: By default, all of the DIP switches are set to the o position.

See the table below for more information about the functions of the dierent DIP

switches.

DIP switch

number

Function State Description

1TP SR

(Short Range Cable Drive)

On Enable if TP cable length is

30 m or less.

O For TP cables that are up to

100 m in length.

2FX LFP

(Link Fault Pass-through)

On Enable LFP on ber side.

O Normal mode.

3TP LB

(Loopback)

On Enable TP loopback mode.

O Normal mode.

4FX LB

(Loopback)

On Enable ber loopback mode.

O Normal mode.

5FFA

(Fiber Fault Alert)

On Enable FFA.

O Disable FFA.

6EEE

(Energy-Ecient Ethernet)

On Enable EEE.

O Disable EEE

Instruction manual

Install the media converter

1. Turn o any networking equipment that will be connected to the media converter.

2. Insert a 10 Gigabit MSA-compliant SFP+ module into media converter’s SFP+ slot.

The SFP+ transceiver must be compatible with your ber network infrastructure.

Note: The media converter can only be used with 10 Gigabit SFP+ modules and will

not support 10/100/1000Mbps modules.

3. Connect a duplex ber-optic cable from the media converter’s SFP+ module to your

ber network device. The TX and RX connectors must be paired at both ends of the

connection (example TX to RX, and RX to TX).

4. Connect an RJ45 Cat6a Ethernet cable from the media converter’s RJ45 port to your

10GbE network device.

5. Select the appropriate power cord for your region and connect it to the power

adapter.

6. Connect the power adapter to an AC electrical outlet and then to the media

converter’s DC power input port. The PWR LED (power) lights up and remains solid

to indicate the media converter is powered.

7. Turn on the networking equipment you turned o in step. The FX Link (ber link)

LED lights up and remains solid when a ber link has been established, and the RJ45

Link (copper link) LED lights up and remains solid when a copper Ethernet link has

been established.

Note: Check the link budget of your SFP+ modules, as well as the module’s intended

wiring distance. SFP+ modules are designed to transmit signals over long distances. If

the physical wiring distance is too short, the transmitting optical signal (laser) may be

too strong and damage the receiving SFP+ module. An in-line optical attenuator may

be required to protect them from damage.

Instruction manual

Installing a second SFP card module

By default, the media converter’s SFP+ card module is preinstalled into slot 2. The

media converter features a secondary slot (slot 1), which lets you install a second

compatible SFP card module (with LC connectors). Once a compatible SFP card module

is installed, you can integrate the media converter into both 10Gb and 1Gb networks.

The media converter is compatible with the following StarTech.com products:

• ET91000SFP2C - GbE Fiber-Media Converter Card Module (card module only)

• ET91000LC2 - GbE Fiber-Media Converter - LC (card module and chassis)

• ET91000LCOAM - GbE Fiber-Media Converter - LC - OAM Managed (card module

and chassis)

• ET91000SFP2 - GbE Fiber-Media Converter - Open SFP Slot (card module and

chassis)

• ET1000S40LC2 - GbE Fiber-Media Conveter - SM - LC (card module and chassis)

Remove a card module from another media converter

If you’re installing a card module from one of the ET91000 media converters, you may

need to remove the card module from that media converter’s chassis.

• Turn the thumbscrew counterclockwise to loosen the SFP card module, and gently

pull the SFP card module from the ET91000*** chassis.

Note: Consult the manual for the ET91000*** series product that you are removing the

card module from for additional details regarding thumbscrew location.

Install a second SFP card module

Follow the instructions below to install a second SFP card module into the media

converter’s slot 1:

1. Turn the screw counterclockwise, using a Phillips screwdriver, and remove the cover

plate from slot 1.

2. Gently insert the card module from one of the compatible media converters into

slot 1.

Note: When properly installed, the card module in slot 1 should be ush with the

preinstalled card module in slot 2.

3. Turn the thumbscrew on the card module that was inserted into slot 1 clockwise to

tighten and secure it to the chassis.

4. Connect your network devices to the second card module using the instructions

noted in the Install the media converter section.

Instruction manual

Managing the media converter

The media converter features two slots:

• Slot 1: Expansion slot for installing another SFP/SFP+ card module

• Slot 2: Preinstalled SFP+ card module

The media converter can be controlled using the DB9 RS232 serial port located on the

rear of the media converter. See the Using the serial console command port section

for further instructions and details.

Using the management switches

The media converter features two switches on the rear:

• Slot selection (left switch): selects which slot to control (slot 1 or slot 2).

• Management type selection (right switch): must be set to the downward (console)

position.

By default, the media converter’s SFP+ card module is inserted into slot 2.

To control the media converter using the DB9 console port, ensure that the

management type selection (right switch) is set in the downward (console) position.

Switch conguration options:

The SFP+ card module is installed in slot

2. The media converter is managed by the

console. (Default)

A SFP+ card module is installed in slot 1.

The media converter is managed by the

console.

Slot 1

Slot 2

Console

Note: The media converter’s management type selection (right switch) must always be

set to the downward (console) position, to control the media converter using the DB9

console port.

Instruction manual

Using the serial console command port

The media converter features a DB9 (RS232 serial) port, which enables console-based

management commands, for enhanced customization and control of the converter.

Media converter default settings:

• Baud Rate: 38,400

• Data bits: 8

• Parity bits: none

• Stop bits: 1

•Handshaking: none

• Emulation: VT-100

•Default username/password: admin/admin (case sensitive)

1. If connected, disconnect the power adapter from the media converter’s DC power

input port.

2. Connect a straight-through DB9 RS232 cable (not provided) from the media

converter’s DB9 serial port to a serial console (for example, a laptop with a DB9 serial

port).

3. Run a terminal emulation application (for example, PuTTY).

4. Reconnect the power adapter that was disconnected in step #1.

Approximately three seconds after you power up the media converter, it will display a

5. Login with the following details:

• User Name: admin (case sensitive)

• Password: admin (case sensitive)

6. Congure and control the media converter to suit your network requirements, using

the available menu options.

Tabla de contenidos

Otros manuales de Convertidor de medios de StarTech.com

StarTech.com

StarTech.com MCS110SC20 Manual de usuario

StarTech.com

StarTech.com ST122LEA Manual de usuario

StarTech.com

StarTech.com ET91000MMSM Manual de usuario

StarTech.com

StarTech.com MCM110SC Manual de usuario

StarTech.com

StarTech.com ET91000SM40 Manual de usuario

StarTech.com

StarTech.com HDMI2HDMI Manual de usuario

StarTech.com

StarTech.com 8STMCM10GSFP Manual de usuario

StarTech.com

StarTech.com ET91000LC Manual del sistema

StarTech.com

StarTech.com SAT32MSAT257 Manual de usuario

StarTech.com

StarTech.com ET1000S40LC2 Manual del sistema

StarTech.com

StarTech.com VGA2HDMIPRO Manual de usuario

StarTech.com

StarTech.com USB32DVCAPRO Manual de usuario

StarTech.com

StarTech.com VGA2VID Manual de usuario

StarTech.com

StarTech.com MCM110ST Manual de usuario

StarTech.com

StarTech.com DVI2HDMI Manual de usuario

StarTech.com

StarTech.com ET1110PSE Manual de usuario

StarTech.com

StarTech.com VGA2VID Manual de usuario

StarTech.com

StarTech.com ET90110ST Manual del sistema

StarTech.com

StarTech.com ET9003SC Manual

StarTech.com

StarTech.com USB2DVIE Manual de usuario

StarTech.com

StarTech.com DP2DVIS Manual de usuario

StarTech.com

StarTech.com MMC110MMST Manual de usuario

StarTech.com

StarTech.com ET90110SM30 Manual del sistema

StarTech.com

StarTech.com MCM1110MMLC Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario