StarTech.com SV565FXDUSA Manual de usuario

Manual Revision: 05/23/2013

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

SV565FXDUSA

USB DVI KVM Console Extender with

Serial & Audio Over MM Fiber - 2km

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use ofTrademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Introduction............................................................................................1

Packaging Contents ................................................................................................................................. 1

System Requirements.............................................................................................................................. 1

Front View.................................................................................................................................................... 2

Rear View...................................................................................................................................................... 2

Installation ..............................................................................................3

Preparing Your Site ................................................................................................................................... 3

Installing the Computer Unit................................................................................................................ 4

Installing the Console Unit .................................................................................................................... 4

Before Cascading with KVM Switch.................................................................................................... 5

Driver Installation...................................................................................................................................... 5

Using the KVM Extender .......................................................................6

Using the Computer Unit ....................................................................................................................... 6

Using the Console Unit ........................................................................................................................... 9

Mask Hotkey Switch................................................................................................................................. 12

Alternative Hot-Key Control.................................................................................................................. 13

Serial Device Setup................................................................................................................................... 14

Fiber Cable Limitations .........................................................................14

Specications..........................................................................................15

Technical Support ..................................................................................17

Warranty Information............................................................................17

Instruction Manual

Introduction

The SV565FXDUSA USB DVI KVM Console Extender w/ Serial & Audio Over MM Fiber

(2km) lets you control a server, computer or multiple computers (connected through

KVM Switch) over a multi-mode ber link, at distances of up to 2000m (6562 ft) away.

By transmitting the digital DVI video (or HDMI with a DVI to HDMI adapter) over a

multi-mode optical ber link there is no loss of signal quality, so the video is as sharp

and vivid as if the monitor was connected directly to the PC.

For added convenience, the Console/KVM extender supports USB computer

connections, and is compatible with any brand of USB KVM Switch.

Backed by a StarTech.com 3-year warranty and free lifetime technical support.

Packaging Contents

• 1x Computer Unit

• 1x Console Unit

• 4x Rackmount Brackets

• 2x Sets of DVI USB and Audio cables

• 1x 30m (98ft) MM Fiber cable

• 1x Rubber feet

• 2x Universal Power Adapter (US/UK/EU)

• 1x Manual

System Requirements

• USB enabled computer or KVM switch

• DVI-D enabled computer or KVM switch

• DVI-D enabled display device

• Standard 104-key wired USB keyboard

• Standard 3-button wired USB mouse

• Multi-Mode ber cable (50/125 or 62.5/125)

• Available electrical outlet at both locations

Instruction Manual

Front View

Rear View

Selection

LED Selection

button

Serial Rx/Tx

LEDs Status

LED

Console DVI

connector

Computer DVI

connector

Console USB keyboard/

mouse connectors

Computer 3.5mm

Audio connectors

Mask Hotkey

switch

Console

Serial port

Computer

Serial port

Computer USB

connector

SC ber

connectors

Console 3.5mm

Audio connectors

Instruction Manual

Installation

WARNING! Do not stare into laser beam or look directly into the ends of the ber, or

look directly into the aperture ports of the ber. Invisible laser radiation can cause

eye injury.

Preparing Your Site

Before you can install the product, you need to prepare your site.

1. Determine where the host computer will be located and set up the computer.

2. Determine where the console devices (mouse, keyboard, monitor) will be located

and place them appropriately.

3. a) If you are using surface cabling, ensure you have enough Multi-Mode Fiber

network cabling to connect the Computer Unit to the Console Unit’s location, and

that each end is terminated with an SC connector. The cabling should not go

through any networking equipment (i.e. router, switch).

b) If you are using premise cabling, ensure that the Multi-Mode Fiber network

cabling between the Computer Unit and the Console Unit has been properly

terminated in a wall outlet in each location and there is a patch cable long enough

to connect the Console Unit and the Computer Unit to their respective outlets. The

cabling should not go through any networking equipment (i.e. router, switch).

Console Unit Computer Unit

Remote

Console *optional

Local Console

(optional) Host computer

Instruction Manual

Installing the Computer Unit

1. Place the Computer Unit near the computer that needs to be controlled.

2. Switch o the computer and disconnect any connected devices.

OPTIONAL: If you wish to have console access locally to the Host computer, connect a

USB mouse, keyboard, and DVI monitor to the connectors marked as “Console” on the

Computer Unit.

3. Connect the power adapter from an AC electrical outlet to the unit.

4. Using the provided StarTech.com USB, DVI, Audio KVM cable, connect the Host

computer system to the KVM Extender’s “Computer” connectors. Reconnect any

necessary peripheral devices to the Host computer, removed in Step 2.

OPTIONAL: If you wish to have the Host computer to have access to a serial device,

connect a DB9 serial cable from the Host computer to the Computer DB9 connector

(DCE) on the Computer Unit. You may connect a serial device locally, by plugging the

serial device into the Console DB9 connector (DTE).

5. Connect the ber cable to the SC ber connectors on the Computer Unit. Connect

the opposite end to a terminated wall outlet (if you are using premise cabling) or

directly to the Console Unit.

6. Power on the Host computer system.

Installing the Console Unit

1. Place the Console Unit near the remote keyboard/mouse/display.

2. Connect a USB keyboard and mouse, and a DVI monitor to the connectors marked

as “Console”on the Console Unit.

OPTIONAL: If the serial connection was setup on the Computer Unit, connect the

serial device to the Console DB9 connector (DTE) on the Console Unit.

3. Connect the power adapter from an AC electrical outlet to the unit.

4. Connect the ber cable connection to the SC ber connector on the Console Unit.

Connect the opposite end to a terminated wall outlet (if using premises cabling) or

directly to the Computer Unit.

Instruction Manual

OPTIONAL: If connecting a computer system to the Console Unit, switch o the

computer and disconnect any existing devices. Using the provided StarTech.com

integrated USB, DVI, Audio KVM cable, connect the computer system to the Console

Unit’s “Computer” connectors. Reconnect any necessary peripheral devices to the Host

computer, removed previously.

Before Cascading with KVM Switch

If connecting the Extender to a KVM switch, make sure that the following have been

completed before connecting the KVM Switch to the Console or Computer Unit.

1. Determine whether a DVI or HDMI display will be used, and then, on the Computer

Unit, set monitor display mode to DVI ( [Press and hold Selection button for 2

seconds] - [V ] - [D] ) or HDMI ( [Press and hold Selection button for 2 seconds] - [V] -

[M] ) accordingly. (The signal from the Computer Unit is transmitted to the Console

Unit in one direction only, so it is not necessary to make this setting on the Console

Unit)

2. Enable Compatibility Mode by entering the hotkey command ( [Ctrl] - [Ctrl] - [Alt] +

[E] ) and then two beeps should be generated as the conrmation. In Compatibility

Mode, set the control to Local or Remote by inputting the hotkey ( [Ctrl] - [Ctrl] - [T] ).

If the KVM Switch is directly connected to Computer Unit, switch ON the Mask

Hotkey switch on both Units. If the KVM Switch is directly connected to the Console

Unit, switch ON the Mask Hotkey switch on the Console Unit only.

Connect the KVM Switch to the Console or Computer Unit after above set up completed.

Driver Installation

The KVM Extender is a complete hardware solution so no software or driver installation

is required on any computer system.

Instruction Manual

Using the KVM Extender

This section details how to use your KVM extender at both the local and

remote locations.

Using the Computer Unit

The Computer Unit allows users connected to the Computer and Console units to share

control of devices (computers, KVM Switches) connected to it.

The Computer Unit has three modes that control which user may access the Host

system (Computer A) at a given time: Auto (the KVM extender looks for keyboard or

mouse activity from both Local and Remote and automatically accepts input from

the active console), Local (only the user seated at the Computer Unit can access the

system), and Remote (only the user at the Console Unit can access the system).

You can use either keyboard shortcuts (if there is a keyboard and mouse attached) or

the mode switch on the front of the Computer Unit to control which user has access to

devices connected to the Computer Unit, by pressing the button in sequence.

By default, the Computer Unit operates in Auto mode, and switches to the next mode in

sequence each time the switch is pressed as follows:

Having a keyboard and mouse attached to the Console ports on the Computer Unit is

recommended, since it oers access to a number of extended features.

LED Indicators

Mode Local Remote

Auto (Auto senses activity) Flashing Flashing

Local (User at Computer Unit has exclusive control) On (solid) O

Remote (User at Console Unit has exclusive control) O On (solid)

Auto Local Remote

Instruction Manual

Keyboard Shortcut Command Sequences

Standard Command With Compatibility

Mode Enabled Description

[Ctrl] - [Ctrl] - [T] [Ctrl] - [Ctrl] - [T]

Toggles control of Computer A

between Auto, Local, and Remote

modes

[Ctrl] - [Ctrl] - [Esc] [Ctrl] - [Ctrl] - [Esc] Cancels the hotkey sequence

[Ctrl] - [Ctrl] - [Alt]+[E] [Ctrl] - [Ctrl] -

[Alt]+[E]

Enables (2 beeps) or disables (1

beep) Compatibility Mode so that

the KVM extender will work with a

KVM switch that also uses a [Ctrl]

hotkey sequence

[Ctrl] - [Ctrl] - [1] [Ctrl] - [Ctrl] - [E] - [1]

Local Mode: Allows the user at

Computer Unit Aexclusive access

to the system; remote access from

Console Unit Bis disabled

[Ctrl] - [Ctrl] - [2] [Ctrl] - [Ctrl] - [E] - [2]

Remote Mode: Allows the user at

Console Unit B exclusive access to

Computer A; access to the computer

from the Computer Unit is disabled

[Ctrl] - [Ctrl] - [3] [Ctrl] - [Ctrl] - [E] - [3] Auto Mode: Wait for console

activity

[Ctrl] - [Ctrl] - [F3] [Ctrl] - [Ctrl] - [E]

- [F3]

Sets the interval of inactivity in

seconds (5,15,30,60) that Computer

Unit will wait before returning to

Auto Mode after a Unit has assumed

control.

[Ctrl] - [Ctrl] - [V] - [D] [Ctrl] - [Ctrl] - [E]

-[V] -[D]

Connected display is a DVI monitor

without Audio.

[Ctrl] - [Ctrl] - [V] - [M] [Ctrl] - [Ctrl] - [E] -[V]

-[M]

Connected display is an HDMI®

monitor with Audio.

[Ctrl] - [Ctrl] - [V] - [C] [Ctrl] - [Ctrl] - [E] -

[V] -[C]

EDID Copy

Copy Local monitor EDID

Otros manuales para SV565FXDUSA

Tabla de contenidos

Otros manuales de Extensor de StarTech.com

StarTech.com

StarTech.com ST12MHDLAN Manual de usuario

StarTech.com

StarTech.com ST121UTP Manual de usuario

StarTech.com

StarTech.com ST121UTP232 Manual de usuario

StarTech.com

StarTech.com SV565UTPDUA Manual de usuario

StarTech.com

StarTech.com SV565UTP Manual de usuario

StarTech.com

StarTech.com VS321HDBTK Manual de usuario

StarTech.com

StarTech.com RS232EXTC5 Manual

StarTech.com

StarTech.com 410VDSLEXT2 Manual de usuario

StarTech.com

StarTech.com 410VDSLEXT Manual de usuario

StarTech.com

StarTech.com ST124HDBT Manual de usuario

StarTech.com

StarTech.com ST121HDBTE Manual de usuario

StarTech.com

StarTech.com SV565LANDUA Manual de usuario

StarTech.com

StarTech.com F35023-USB-EXTENDER Manual de usuario

StarTech.com

StarTech.com VS321HDBTK Manual de usuario

StarTech.com

StarTech.com ST121R Manual de usuario

StarTech.com

StarTech.com SV565FXHD4KU Manual de usuario

StarTech.com

StarTech.com ST121SHD50 Manual de usuario

StarTech.com

StarTech.com ST121HDBT20L Manual de usuario

StarTech.com

StarTech.com ST128UTPE Manual de usuario

StarTech.com

StarTech.com USB2004EXTGB Manual de usuario

StarTech.com

StarTech.com ST122UTPAL Manual de usuario

StarTech.com

StarTech.com ST1218T Manual de usuario

StarTech.com

StarTech.com SV565UTPU Manual de usuario

StarTech.com

StarTech.com STUTPRXL Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario