ST SPC58NHADPT176S Manual de usuario
Introduction
The SPC58NHADPT176S Rev.A evaluation board supports STMicroelectronics SPC58NH92 microcontroller in LQFP
24X24X1.4 176L.
Figure 1. SPC58NHADPT176S Rev.A
Note: picture not contractual
SPC58NHADPT176S Rev.A evaluation board
UM2731
User manual
UM2731 - Rev 1 - September 2020
For further information contact your local STMicroelectronics sales office.
www.st.com
1Overview
The SPC58NHADPT176S Rev. A mini module is an evaluation board supporting STMicroelectronics SPC58NH92
microcontroller in LQFP 24X24X1.4 176L package (LQFP 24X24X1.4 176L P0.5 EXPOSED PAD).
This mini module is designed to be connected onto the SPC58XXMB/SPC57XXMB motherboard, offering a
mechanism for easy customer evaluation of the supported devices, and to facilitate hardware and software
development.
The mini module may be used as a stand-alone unit allowing access to the CPU, but not to access to the I/O pins
nor any motherboard peripherals.
1.1 Package contents
A SPC58NHADPT176S Rev. A adapter package includes the following items:
• SPC58NHADPT176S Rev. A mini module
1.2 Supported devices
The SPC58NHADPT176S Rev. A mini module supports the SPC58NH family in LQFP 24X24X1.4 176L package.
UM2731
Overview
UM2731 - Rev 1 page 2/37
2License agreement
The packaging of this evaluation board was sealed with a seal stating, “by breaking this seal, you agree to the
terms and conditions of the evaluation board license agreement, the terms and conditions of which are available
at http://www.st.com/ebla”. Upon breaking the seal, you and STMicroelectronics entered into the evaluation board
license agreement, a copy of which is also enclosed with the evaluation board for convenience.
Attention: This evaluation board only offers limited features for evaluating ST products. It has not been tested for use with
other products and is not suitable for any safety or other commercial or consumer application. This evaluation
board is otherwise provided “AS IS” and STMicroelectronics disclaims all warranties, express or implied,
including the implied warranties of merchantability and fitness for a particular purpose.
UM2731
License agreement
UM2731 - Rev 1 page 3/37
3Handling precautions
Please take care to handle the package contents in a manner such as to prevent electrostatic discharge.
Before the EVB is used or power is applied, please fully read the following sections on how to correctly configure
the board. Failure to correctly configure the board may cause irreparable component, MCU or EVB damage.
UM2731
Handling precautions
UM2731 - Rev 1 page 4/37
4Hardware description
4.1 Hardware features
The SPC58NHADPT176S Rev. A mini module board has the following features:
• Connector for external power supplies input (5V) used in stand-alone mode
• Reset button with driver and led indicator
• Socket for device in LQFP 24X24X1.4 176L package
• Debug interfaces:
– 14-pin header connector for JTAG interface
– 10-pin header connector for JTAG/LFAST LVDS interface
– 10-pin header connector for SIPI interface
• 40 MHz crystal main oscillator with jumpers to optionally disconnect it
• 8 MHz oscillator with jumpers to optionally disconnect it
• Clock input through SMA connector with jumper to optionally disconnect it
• 2 X SAMTEC QSH series, 240-way connector to connect mini module to Motherboard
• 1 Gb/s Ethernet port
• HyperRAM and HyperFlash connected to HyperBUS interface
• Embedded eMMC device
• SD/MMC Card Reader
• 12x2 I/O connector
UM2731
Hardware description
UM2731 - Rev 1 page 5/37
4.2 Hardware dimension
The mini module has the following dimensions:
• PCB area: 127 mm x 114.3 mm
• Top components height: 19 mm max
• Bottom components height: 3.5 mm max
• PCB thickness: 1.6 mm
Figure 2. SPC58NHADPT176S Rev. A top component view
UM2731
Hardware dimension
UM2731 - Rev 1 page 6/37
5Power and system configuration
5.1 Power supplies
The mini module can be powered by providing voltages either supplied externally by the 2-Way PCB screw
connector (CN1) or supplied by the motherboard.
When the mini module is connected to the motherboard (MB), 3V3 and 5V0 are supplied by MB connector
selecting the associated jumpers. In this setup the external power supply input available on the mini module
MUST NOT BE USED.
When the SPC58NHADPT176S Rev. A mini module is used as a stand-alone board, 5V0 voltages must be
supplied externally, 3V3 and 1V2 voltages will be generated internally by specific circuit on the mini module.
The following jumpers are used to configure the power supply (common for all supported devices):
Table 1. Power configuration jumpers
Jumper Description Default Position
J1
5.0V source for J3 pin1 (MB_5.0V_LR or 5.0
V_ADC) voltage configuration:
• 1-2 MB_5.0V_LR
• 2-3 5.0 V_ADC
2-3
(5.0V_ADC)
Figure 8. Overview of
SPC58NHADPT176S Rev. A mini
module - Top - C3
J2
5.0V switching voltage configuration:
• 1-2 5 V EXT (external 5.0V supply)
• 2-3 MB_5.0V_SR (5.0V from
Motherboard)
2-3
(MB_5.0V_SR)
Figure 8. Overview of
SPC58NHADPT176S Rev. A mini
module - Top - D4
J3
VDD_HV_ADR_S / VDD_HV_ADV voltage
configuration:
• 1-2 5.0V source from J1 pin2
• 2-3 3.3 V_ADC source from J4 pin2
1-2
(5.0V_ADV)
Figure 8. Overview of
SPC58NHADPT176S Rev. A mini
module - Top - C3
J4
3V3 source (3.3V or MB_3.3V_SR) voltage
configuration:
• 1-2 3.3V (3.3V from mini module)
• 2-3 MB_3.3V_SR
1-2
(3.3V)
Figure 8. Overview of
SPC58NHADPT176S Rev. A mini
module - Top - D3
J5
Main MCU supply (VDD_HV_IO_MAIN) voltage
configuration:
• 1-2 5.0V_SR
• 2-3 3.3 V_SR from J4 pin2
1-2
(5.0V_SR)
Figure 8. Overview of
SPC58NHADPT176S Rev. A mini
module - Top - D3
J6
Supply for BALLAST circuit configuration
• 1-2 VDD_HV_IO_MAIN
• 2-3 5.0V_SR
1-2
(VDD_HV_IO_MAIN)
Figure 8. Overview of
SPC58NHADPT176S Rev. A mini
module - Top - D3
J7
BALLAST CIRCUIT ENABLE
• Closed: enable
• Open: disable
Closed
(enable)
Figure 8. Overview of
SPC58NHADPT176S Rev. A mini
module - Top - D2
J8
VDD_LV voltage configuration:
• 1-2 (1.2V_SR from J9 pin2)
• 2-3 (BALLAST circuit)
1-2
(1.2V_SR)
Figure 8. Overview of
SPC58NHADPT176S Rev. A mini
module - Top - C3
J9
1.2V_SR switching configuration:
• 1-2 MB_1.25V_SR (1.25V from MB)
• 2-3 1.2V (1.2V from mini module)
2-3
(1.2V from mini module)
Figure 8. Overview of
SPC58NHADPT176S Rev. A mini
module - Top - D3
UM2731
Power and system configuration
UM2731 - Rev 1 page 7/37
5.2 JTAG/LFAST LVDS interface configuration
The following jumpers need to configure the JTAG/LFAST LVDS/SIPI:
Table 2. JTAG/LFAST/SIPI Configuration jumpers
Jumper Description Default Position
J10
SIPI pin 3 configuration
• 1-2: RDY
• 2-3: PA14
1-2
(RDY) Figure 8. Overview of SPC58NHADPT176S Rev. A mini module - Top - A4
J11
TDI_LF configuration
• 1-2: TDI_LF
• 2-3: PA8
1-2
(TDI_LF) Figure 8. Overview of SPC58NHADPT176S Rev. A mini module - Top - A4
J12
TDO_LF configuration
• 1-2: TDO_LF
• 2-3: PA9
1-2
(TDO_LF) Figure 8. Overview of SPC58NHADPT176S Rev. A mini module - Top - A4
J13
JTAG pin 13 configuration
• 1-2: EVTO
• 2-3: PJ3/PQ4
1-2
(EVTO) Figure 8. Overview of SPC58NHADPT176S Rev. A mini module - Top - B4
J14
PC1 / ESR0
• 1-2 ESR0
• 2-3 PC1
1-2
(ESR0) Figure 8. Overview of SPC58NHADPT176S Rev. A mini module - Top - B4
J15
EVTO/ESR0
• 1-2 ESR0
• 2-3 EVTO
1-2
(ESR0) Figure 8. Overview of SPC58NHADPT176S Rev. A mini module - Top - B4
UM2731
JTAG/LFAST LVDS interface configuration
UM2731 - Rev 1 page 8/37
5.3 System clock configuration
The mini module supports the usage of crystal clock sources as well as external clock source:
Table 3. Clock configuration jumpers
Jumper Description Default Position
J20
XTAL32 configuration
• Close: connect pin 2 of 32.768 KHz crystal
(Y2) to XTAL32
Open Figure 8. Overview of SPC58NHADPT176S
Rev. A mini module - Top - C3
J21
EXTAL32 configuration
• Close: connect pin 1 of 32.768 KHz crystal
(Y2) to EXTAL32
Open Figure 8. Overview of SPC58NHADPT176S
Rev. A mini module - Top - C3
J17
EXTAL configuration
• 1-2 connect pin 2 of 40 MHz crystal (Y1) to
EXTAL
• 2-3 connect EVB-EXTAL to EXTAL
1-2
(Y1 pin2 to
EXTAL)
Figure 8. Overview of SPC58NHADPT176S
Rev. A mini module - Top - C2
J19
XTAL configuration
• 1-2 connect pin 1 of 40 MHz crystal (Y1) to
XTAL
• 2-3 connect XTAL to GND
1-2
(Y1 pin1 to
XTAL)
Figure 8. Overview of SPC58NHADPT176S
Rev. A mini module - Top - C2
J18
Enable 8 MHz oscillator power supply
• open - power off
• closed - power on
Open
(power off)
Figure 8. Overview of SPC58NHADPT176S
Rev. A mini module - Top - C1
J22
External 8 MHz clock source
• 1-2 OSC-MOD (from oscillator)
• 2-3 EXTAL-SMA (from SMA connector)
1-2
(8 MHz from
oscillator)
Figure 8. Overview of SPC58NHADPT176S
Rev. A mini module - Top - C2
5.4 Reset circuit
The mini module supports different ways to reset the microcontroller. To use and perform the reset driving there
are different jumpers and switches:
Table 4. Reset configuration jumpers
Jumper Description Default Position
SW1 Reset push button Open Figure 8. Overview of SPC58NHADPT176S Rev. A
mini module - Top - A4
J24
Connect the external
reset to the reset driver
for ESR0 and PORST
pins
Close Figure 8. Overview of SPC58NHADPT176S Rev. A
mini module - Top - C4
J23 Connect the external
reset to ESR0 pin Close Figure 8. Overview of SPC58NHADPT176S Rev. A
mini module - Top - C4
J25 Connect the external
reset to PORST pin Close Figure 8. Overview of SPC58NHADPT176S Rev. A
mini module - Top - C4
UM2731
System clock configuration
UM2731 - Rev 1 page 9/37
5.5 Other Jumpers
Table 5. Other jumpers
Jumper Description Default Position
J16 TESTMODE settings Close
(10 KΩ down)
Figure 8. Overview of SPC58NHADPT176S Rev. A
mini module - Top - B2
5.6 Configuration for pin shared between HyperBus & eMMC
The jumpers described into the following table allow you to configure the pins shared between HyperBus and
eMMC.
Table 6. Pin shared between HyperBus & eMMC jumper
Jumper Description Default configuration Position
J27
Data4 - PF9 configuration
• 1-2 DQ4_HB
(HyperBus)
• 2-3 D4_eMM
(eMMC)
1-2
(HyperBus)
Figure 8. Overview of SPC58NHADPT176S Rev. A
mini module - Top - B2
J29
Data5 – PF10
configuration
• 1-2 DQ5_HB
(HyperBus)
• 2-3 D5_eMM
(eMMC)
1-2
(HyperBus)
Figure 8. Overview of SPC58NHADPT176S Rev. A
mini module - Top - B2
J31
Data6 - PF11
configuration
• 1-2 DQ6_HB
(HyperBus)
• 2-3 D6_eMM
(eMMC)
1-2
(HyperBus)
Figure 8. Overview of SPC58NHADPT176S Rev. A
mini module - Top - B2
J34
Data7 - PF12
configuration
• 1-2 DQ7_HB
(HyperBus)
• 2-3 D7_eMM
(eMMC)
1-2
(HyperBus)
Figure 8. Overview of SPC58NHADPT176S Rev. A
mini module - Top - B2
UM2731
Other Jumpers
UM2731 - Rev 1 page 10/37
Tabla de contenidos
Otros manuales de Placa madre de ST
ST
ST STM32100B-EVAL Manual de usuario
ST
ST FDA803S Manual de usuario
ST
ST STM32F746G-DISCO Manual de usuario
ST
ST SPC572LADPT80S Manual de usuario
ST
ST X-NUCLEO-IKS01A1 Manual de usuario
ST
ST SPC58NG-DISP Manual de usuario
ST
ST P-NUCLEO-IOD01A1 Manual de usuario
ST
ST STEVAL-IHM011V1 Manual de usuario
ST
ST STA333ML Instrucciones de instalación y funcionamiento
ST
ST STCC50x1 Manual de usuario
ST
ST SPC572LADPT100S Manual de usuario
ST
ST STM32L152RCT6 Discovery kit Manual de usuario
ST
ST STEVAL-IPE005V1 Manual de usuario
ST
ST STM32303E-EVAL Manual de usuario
ST
ST STM32H753I-EVAL Manual de usuario
ST
ST STM32G0C1E-EV Manual de usuario
ST
ST EnFilm EFL1K0AF39 Manual de usuario
ST
ST STM32L4 Series Manual de usuario
ST
ST STEVAL-QUADV01 Manual de usuario
ST
ST STEVAL-IPP003V1 Guía de inicio rápido
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
