ST STM32100B-EVAL Manual de usuario

February 2010 Doc ID 16533 Rev 2 1/41

UM0841

User manual

STM32100B-EVAL

evaluation board

Introduction

The STM32100B-EVAL is an evaluation board for STMicroelectronic’s ARMTM Cortex-M3

core-based STM32F100VBT6 microcontroller. It is designed as a complete development

environment with HDMI CEC, two I2C channels, two SPI channels, three USART channels,

8 KB internal SRAM and 128 KB internal Flash, and JTAG and SWD debugging support.

With a complete range of hardware evaluations features, the STM32100B-EVAL board is

designed to help developers evaluate all device peripherals (such as HDMI CEC, motor

control, LCD, MicroSD Card™, serial Flash, speaker, IrDA and USART) and develop their

own applications. Extension connectors make it possible to easily connect a daughterboard

or wrapping board for a specific application.

An ST-LINK is integrated on the board as an embedded in-circuit debugger and programmer

for the STM32F100VBT6 MCU.

Figure 1. STM32F100VBT6 evaluation board (STM32100B-EVAL)

www.st.com

Downloaded from Elcodis.com electronic components distributor

Contents UM0841

2/41 Doc ID 16533 Rev 2

Contents

1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Demonstration software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 Order code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Hardware layout and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Boot option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 Reset source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.5 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.6 Serial Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.7 RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.8 Motor control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.9 MicroSD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.10 Temperature sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.11 Development and debug support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.12 Analog input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.13 IrDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.14 Display and input devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.15 IDD measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.15.1 Run mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.15.2 Low power mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.15.3 Standby or Stop IDD measurement procedure . . . . . . . . . . . . . . . . . . . 12

2.15.4 Low IDD measurement improvement procedure . . . . . . . . . . . . . . . . . . 13

2.16 HDMI CEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.1 Audio jack CN1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.2 JTAG debugging connector CN3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.3 Daughterboard extension connectors CN4 and CN5 . . . . . . . . . . . . . . . . 15

3.4 Motor control connector CN6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Downloaded from Elcodis.com electronic components distributor

UM0841 Contents

Doc ID 16533 Rev 2 3/41

3.5 Analog input connector CN7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.6 Power supply connector CN8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.7 RS-232 connector CN9 with RTS/CTS handshake support . . . . . . . . . . . 21

3.8 RS-232 connector CN10 with ISP support . . . . . . . . . . . . . . . . . . . . . . . . 21

3.9 MicroSD connector CN11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.10 ST-LINK connector CN12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.11 ST-LINK programming connector CN13 . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.12 HDMI connectors CN15 and CN16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4 Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.1 Boot switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.2 PE14, PB14 and PA10 usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.3 Jumper JP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.4 Audio amplifier volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.5 IDD standby measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Appendix A STM32100B-EVAL I/O assignments . . . . . . . . . . . . . . . . . . . . . . . . . 37

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Downloaded from Elcodis.com electronic components distributor

Overview UM0841

4/41 Doc ID 16533 Rev 2

1 Overview

1.1 Features

●Three 5 V power supply options: power jack, ST-LINK connector or daughterboard

●Boot from user Flash, system memory or SRAM

●Speaker

●1 Gbyte MicroSD Card™

●16 Mbyte serial Flash

●I2C/SMBus compatible serial interface temperature sensor

●Two RS-232 communication channels with support for RTS/CTS handshake on one

channel

●IrDA transceiver

●Induction motor control connector

●JTAG and SWD debug support

●240x320 TFT color LCD

●Joystick with 4-direction control and selector

●Reset, wakeup, tamper and user push buttons

●Four LEDs

●RTC with backup battery

●Extension connector for daughterboard or wrapping board

●Embedded ST-LINK

●IDD current measurement circuit

●HDMI CEC

1.2 Demonstration software

Demonstration software is preloaded in the board's Flash memory for easy demonstration of

the device peripherals in stand-alone mode. For more information and to download the

latest version available, please refer to the STM32100B-EVAL demonstration software

available on www.st.com.

1.3 Order code

To order the STM32F100VBT6 evaluation board, use the order code STM32100B-EVAL.

Downloaded from Elcodis.com electronic components distributor

UM0841 Hardware layout and configuration

Doc ID 16533 Rev 2 5/41

2 Hardware layout and configuration

The STM32100B-EVAL board is designed around a STM32F100VBT6 microcontroller in a

100-pin LQFP package.

The hardware block diagram Figure 2 shows the connections between the

STM32F100VBT6 microcontroller and the peripherals (LCD, SPI Flash, USART, IrDA,

speaker, HDMI CEC, temperature sensor, MicroSD Card, motor control and embedded ST-

LINK).

Figure 3 will help you locate these features on the evaluation board.

Figure 2. Hardware block diagram

34-&6"4 23

TRANSCEIVER

)R$!

TRANSCEIVER

6REGULATOR

4&4COLOR

,#$

-ICRO3$

#ARD

3PEAKER

AMPLIFIER

".#

CONNECTOR

,%$S

0OTENTIOMETER

53!24

$"CONNECTOR

$!#

'0)/

)# %XTENSION

CONNECTORFOR

'0)/S

-#5

CONSUMPTION

MEASUREMENT

53!24

4EMPERATURE

SENSOR

*4!'

*OYSTICK

!$#

%MBEDDED

34,).+

53"4YPE"

CONNECTOR

"UTTONS

!$#

-OTOR#ONTROL

CONNECTOR -#

*4!'4RACE

CONNECTOR

53!24

$"CONNECTOR

30)

53!24

23

TRANSCEIVER

53!24

3ERIAL&LASH

30)

#%#

)#

($-)

CONNECTOR

($-)

CONNECTOR

Downloaded from Elcodis.com electronic components distributor

Hardware layout and configuration UM0841

6/41 Doc ID 16533 Rev 2

Figure 3. STM32100B-EVAL board layout

CN4, CN5

Extension connector

CN9

USART2

CN10

USART1

CN11

MicroSD

U14

IrDA

CN8

Power jack

RV2

Potentiometer B1

RESET B2

WAKEUP B3

Tamper U4

Joystick B4

Key

CN6

Motor control

CN16

HDMI

connector

CN15

HDMI

connector

CN3

JTAG

CN12

ST-LINK

U14

Color LCD

CN1

Audio jack

CN7

BNC

RV1

Potentiometer

VALUELINE

Downloaded from Elcodis.com electronic components distributor

UM0841 Hardware layout and configuration

Doc ID 16533 Rev 2 7/41

2.1 Power supply

The STM32100B-EVAL board is designed to be powered by a 5 V DC power supply and to

be protected by PolyZen U10 in case of incorrect power supply configuration.

It is possible to configure the evaluation board to use any of the following sources for the

power supply:

●5 V DC power adapter connected to CN8, the power supply jack labeled “PSU” (for

power supply unit) on the silkscreen.

●5 V DC power with 500 mA limitation from CN12, the ST-LINK type-B USB connector

labeled “USB” on the silkscreen.

●5 V DC power from both CN4 and CN5, the daughterboard extension connectors

labeled “DTB” (for daughterboard) on the silkscreen.

The power supply is configured by setting jumpers JP9 and JP10 as described in Table 1.

To enable MCU power consumption measurement, JP8 and JP12 should be re-configured

as described in Table 2. (PCB rev B only. See Section 4.5: IDD standby measurement for

details.)

LED LD5 is lit when the STM32100B-EVAL board is correctly powered by 5 V.

Note: The AC220V to DC5V power adapter PSU-5V2A (recommended and can be ordered from

ST, it is not provided with board by default) or equivalent power adapter (polarity compatible

with CN8) can be used to power STM32100B-EVAL board via power jack CN8 on the board.

To order the recommended power supply, use the order code PSU-5C2A.

Table 1. Power jumpers

Jumper Description

JP10

JP10 is used to select one of the three possible power supply resources.

For power supply from the power supply jack (CN8) to the

STM32100B-EVAL only, JP10 is set as shown:

For power supply from the daughterboard connectors (CN4 and CN5)

to the STM32100B-EVAL only, JP10 is set as shown:

For power supply from the ST-LINK USB connector (CN12) to the

STM32100B-EVAL only, JP10 is set as shown (default setting):

For power supply from power supply jack (CN8) to both the

STM32100B-EVAL board and to a daughterboard connected on CN4

and CN5, JP10 is set as shown: The daughterboard must not have its

own power supply connected.

JP9

Vbat is connected to VDD_MCU power when JP9 is set as shown (default

setting):

Vbat is connected to battery when JP9 is set as shown:

PSU

DTB

USB

PSU

DTB

USB

PSU

DTB

USB

PSU

DTB

USB

1 2 3

Downloaded from Elcodis.com electronic components distributor

Hardware layout and configuration UM0841

8/41 Doc ID 16533 Rev 2

2.2 Boot option

The STM32100B-EVAL board can boot from:

●Embedded user Flash

●System memory with boot loader for ISP

●Embedded SRAM for debugging

The boot option is configured by switches SW1 and SW2 as shown in Table 3.

Note: The hardware implementation of JP4 and the RS-232 interface can be only used when the

Boot0 is at a high level through the onboard switch SW2, which is not the most common

case of usage.

Table 2. MCU power consumption measurement jumpers

Jumper Description

JP8

VDD power is directly connected to MCU VDD when JP8 is set as shown:

(Default setting)

Note: For manual IDD measurement JP8 must be removed and replaced by an ammeter

connected between JP8 pins 1 and 2.

Connect VDD power to MCU with current-sampling resistor, 1Ωor 1KΩ, in series

for IDD current measurement when JP8 is set as shown:

JP12 (Available only on PCB rev B.) Connect IDD_CNT_EN (PE14) to Anti-tamper (PC13) for

IDD current measurement in standby mode when JP12 is closed.

Default setting: Not fitted

1 2 3

Table 3. Boot switches and jumper

Switch Boot from Switch configuration

SW1

SW2

STM32100B-EVAL boots from user Flash when SW2 is set as

shown to the right (default setting).

In this configuration, the position of SW1 does not affect the boot

process.

STM32100B-EVAL boots from embedded SRAM when SW1 and

SW2 are set as shown to the right.

STM32100B-EVAL boots from system memory when SW1 and

SW2 are set as shown to the right.

JP4

BOOT0 pin of the STM32F100VBT6 is connected to the RS-232

connector CN10 pin 8 (CTS) for ISP support when JP4 is closed.

This configuration is used for boot loader application only.

Default setting: not fitted.

SW2

Boot

0 <--> 1

Boot

SW2

Boot

0 <--> 10 <--> 1

SW2

Boot

SW1

Boot

Downloaded from Elcodis.com electronic components distributor

UM0841 Hardware layout and configuration

Doc ID 16533 Rev 2 9/41

2.3 Clock source

Two clock sources are available on the STM32100B-EVAL board for the STM32F100VBT6

microcontroller and RTC.

●X1, 32 KHz crystal for embedded RTC

●X2, 8 MHz crystal with socket for the STM32F100VBT6 microcontroller. It can be

removed from the socket when the internal RC clock is used.

2.4 Reset source

The reset signal of the STM32100B-EVAL board is active low and the reset sources include:

●Reset button B1

●Debugging tools from JTAG connector CN3

●Daughterboard from CN5

●Embedded ST-LINK

●Bootloader_Reset from RS-232 connector CN10

2.5 Audio

The STM32100B-EVAL board supports playback based on a speaker on the board. This

can be disabled or enabled by jumpers JP1 and JP2. The audio volume can be adjusted

using the potentiometer RV1. See Section 4.4: Audio amplifier volume.

2.6 Serial Flash

A 128 Mbit serial Flash connected to SPI1 of the STM32F100VBT6 microcontroller shares

the same SPI port with the MicroSD Card using a different chip select signal. Serial Flash

chip select is managed by the standard I/O port PD9.

Table 4. Reset jumper

Jumper Description

JP5

Bootloader_Reset signal from the RS-232 connector CN10 pin 1 (DCD) is connected

to RESET# of the STM32F100VBT6 when JP5 is closed.

This configuration is used for the boot loader application only.

Default setting: Not fitted

Table 5. Audio jumpers

Jumper Description

JP1 Audio power amplifier TS4990IST is forced on standby mode when JP1 is fitted.

Default setting: Not fitted

JP2 The DAC _OUT(PA4) is connected to speaker circuit when JP2 is closed.

Default setting: Fitted

Downloaded from Elcodis.com electronic components distributor

Hardware layout and configuration UM0841

10/41 Doc ID 16533 Rev 2

2.7 RS-232

Two type D 9-pin connectors, CN10 (USART1) and CN9 (USART2) are available on the

STM32100B-EVAL board.

●CN10 connects to the RS-232 transceiver U15 with Bootloader_Reset and

Bootloader_BOOT0 support.

●CN9 connects to the RS-232 transceiver U13 with RTS/CTS handshake signal support.

2.8 Motor control

The STM32100B-EVAL board supports induction motor control via a 34-pin connector, CN6,

which provides all required control and feedback signals to and from a motor power-drive

board. Available signals on this connector include emergency stop, motor speed, 3-phase

motor current, bus voltage, heat sink temperature coming from the motor drive board and 6

channels of PWM control signals going to the motor drive circuit.

Special motor current sampling operation is enabled by setting jumper JP7.

Note: On MB871 PCB rev A MC_CurrentA shares PC1 with VBAT_ADCIN through JP3 so the

jumper JP3 must be removed for motor control applications. See Section 4.3: Jumper JP3.

2.9 MicroSD Card

The 1 Gbyte MicroSD Card connected to SPI1 of the STM32F100VBT6 microcontroller

(shared with serial Flash), is available on the board. MicroSD Card chip selection is

managed by the standard I/O port PC12 while the MicroSD card defect signal is managed

by I/O port PE7.

2.10 Temperature sensor

One I2C interface temperature sensor STLM75 (–55°C to +125°C) connected to I2C1 of the

STM32F10x microcontroller, is available on the board.

2.11 Development and debug support

An embedded ST-LINK STM32 JTAG interface developed by STMicroelectronic’s is

available on the STM32100B-EVAL as the default debugger hardware interface.

Of course, third-party debugger interfaces are also supported by the JTAG connector CN3.

Table 6. Motor control jumpers

Jumper Description

JP7

The special motor current sampling operation is enabled when JP7 is fitted (PD2

connected to PB0). The I/O pins PD2 and PB0 are disconnected and can be used by

daughterboard when JP7 is not fitted.

Default setting: Not fitted

JP6 JP6 should be kept open when encoder signal is from pin 31 of motor control connector

CN6. It should be kept closed when analog signal is from pin 31 of CN6 for special motor.

Default setting: Not fitted (open)

Downloaded from Elcodis.com electronic components distributor

Otros manuales para STM32100B-EVAL

Tabla de contenidos

Otros manuales de Placa madre de ST

ST STEVAL-IPMM10B Manual de usuario

ST AEK-MOT-TK200G1 Manual de usuario

ST STM32 Nucleo Instrucciones de instalación y funcionamiento

ST FDA803S Manual de usuario

ST STR730-EVAL Manual de usuario

ST SPC58XXADPT144S REV.B Manual de usuario

ST EVAL-L9960 Manual de usuario

ST STEVAL-PCC010V1 Manual de usuario

ST STMPE801 Manual de usuario

ST STM32L152-EVAL Instrucciones de instalación y funcionamiento

ST EVALSPEAr320PLC Manual de usuario

ST NUCLEO-F207ZG Manual de usuario

ST SPC58XXADPT292S Manual de usuario

ST EVALSTGAP2S Manual de usuario

ST X-NUCLEO-IDB05A1 Manual de usuario

ST UM0969 Manual de usuario

ST B-L4S5I-IOT01A Manual de usuario

ST STSW-S2LP-KNX-DK Manual de usuario

ST STEVAL-ILL059V1 Manual de usuario

ST ST25DV-I2C Manual de usuario

ST SPC58XXADPT144S REV.B Manual de usuario

ST SPC58NHADPT176S Manual de usuario

ST STEVAL-DIGAFEV1 Manual de usuario

ST STM32MP157D-EV1 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario