ST ST92163 Manual de usuario

ST9 FAMILY

ST92163 DEMO BOARD

USER MANUAL

Release 1.0

June 1999

DOC- ST92163 DEMO BOARD

USE IN LIFE SUPPORT DEVICES OR SYSTEMS MUST BE EXPRESSLY AUTHORIZED.

STMicroelectronics PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN

LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF

STMicroelectronics. As used herein:

1. Life support devices or systems are those

which (a) are intended for surgical implant into

the body, or (b) support or sustain life, and

whose failure to perform, when properly used in

accordance with instructions for use provided

with the product, can be reasonably expected

to result in significant injury to the user.

2. A critical component is any component of a life

support device or system whose failure to

perform can reasonably be expected to cause

the failure of the life support device or system,

or to affect its safety or effectiveness.

June 1999 1/17

Rev. 1.0

ST92163

DEMO BOARD

1 INTRODUCTION

The objective of this Demo Board is to provide the user with a hardware platform for rapid de-

velopment of an USB application with the ST92163 microcontroller. Starting from this

ST92163 Demo Board, the developer can add his own application by using the wrapping area

or with a daughter board connected via the 64 pin connector.

To help developers get familiar with USB applications, an example is provided and pro-

grammed in the ST92E163. After setting some jumpers, as described in chapter 3, the user

can plug the ST92163 Demo Board to the PC with the USB cable and dialogue with the ST

Demo Board software via different HID transfers.

Figure 1. ST92163 DEMO BOARD

2/17

Table of Contents

1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2 ST92163 DEMO BOARD CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . 4

2.1 HARDWARE FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.2 FEATURES AND FUNCTIONS DESCRIPTION . . . . . . . . . . . . . . . . . . . . 5

2.2.1 RESET BUTTON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2.2 RS232 CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2.3 I2C CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2.4 TRIMMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2.5 LEDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2.6 I/O CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2.7 I/O EXPANSION CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2.8 EXTERNAL MEMORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2.9 POWER SUPPLY CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 ST92163 DEMO BOARD SCHEMATIC . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 BILL OF MATERIALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 ST92163 DEMO BOARD EXAMPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.3 HID TRANSFER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.4 USING THE EXAMPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.4.1 START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.4.2 Button State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.4.3 Trimmer Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.4.4 LED Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.4.5 PWM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3/17

INTRODUCTION

The following items are supplied in this package:

– ST92163 Demo Board.

– ST92E163 programmed with a HID transfer demonstration.

– User manual (this document).

– Floppy disk with the ST Demo Board software need to use the HID transfer demonstration.

– ST92163 Datasheet.

– ”ST9 8/16-BIT MCU FAMILY” CD ROM.

– USB cable.

4/17

ST92163 DEMO BOARD CHARACTERISTICS

2 ST92163 DEMO BOARD CHARACTERISTICS

This ST92163 Demo Board has been designed to offer to developer a wide range of possibil-

ities for developing his specific application as fast as possible.

The following chapters describe all the characteristics of the ST92163 Demo Board.

2.1 HARDWARE FEATURES

The figure 2 shows the ST92163 Demo Board block diagram with all the components usable

on this board.

Figure 2. ST92163 Demo Board synoptic

Wrapping Area

ST92163

32K

SRAM

64K

EPROM

FLASH

Address

Latches

RS232

MAX232

I/O Expansion connector

USB Upstream portTrimmer

Jack

INT7

Connector

5”1/4 PC

Connector

Reset

Port 6 LEDs

Power

Supply

I2C connector

I/O connector 1

I/O connector 2

Power Supply

LED

5/17

ST92163 DEMO BOARD CHARACTERISTICS

2.2 FEATURES AND FUNCTIONS DESCRIPTION

2.2.1 RESET BUTTON

A reset button is provided for resetting the ST92163 microcontroller. The inverted reset signal

is available to the user via pin 30 of the I/O expansion connector.

2.2.2 RS232 CONNECTOR

The ST92163 Demo Board has one DB9 male connector and uses a standard RS232 cable

for communication between the ST92163 microcontroller and an external peripheral or a PC.

The following jumper configuration allows the developer to connect RS232 signals directly to

the ST92163 microcontroller . Note that all DB9 connector (P1) signals are available via the I/

O expansion connector (pins 1 to 7 and pin 34) and via the I/O connectors TP1 (pins 26 to 32)

and TP2 (pin 31).

Furthermore the ST92163 Demo Board allows the use of special peripherals (RS232 mouse

for example) by connecting the pin 7 of the DB9 connector to the VCC through a jumper (JP3).

Table 1. RS232 signal jumper configurations

2.2.3 I2C CONNECTOR

The ST92163 Demo Board has one connector (P2) for I2C communication.

The following table shows the correspondence between I2C connector pins and ST92163 mi-

crocontroller pins.

Table 2. I2C connector and ST92163 pin correspondence

2.2.4 TRIMMER

A trimmer (R8) let you exercise the Analog to Digital Converter. You only need to put a jumper

on JP8 to connect the ADC IN pin (P6.2) to the trimmer.

2.2.5 LEDS

Three LEDs can be directly driven from microcontroller Port 6. They can be used to test the

ST92163 I/Os. You only need to put jumpers on JP10, JP11 and JP12 to use the LEDs

jumper on RS232 signal

JP3 RTS/VCC

JP4 CTS/P3.4

JP5 RTS/P3.1

JP6 TD/P3.0

JP7 RD/P3.5

I2C connector pin ST92163 pin

1SDA/P6.0

2SCL/P6.1

3 VCC (5V)

4GND

6/17

ST92163 DEMO BOARD CHARACTERISTICS

The following table shows the correspondence between the LEDs and the Port 6 pins.

Table 3. Correspondence between LEDs and Port 6 pins

2.2.6 I/O CONNECTOR

The two I/O connectors TP1 and TP2 allow you to probe or to connect all the microcontroller

pins, the address latch outputs, the RS232 DB9 connector pins, VCC and GND.

The following table shows the correspondence between I/O connector pins and signals.

Table 4. I/O connectors TP1 and TP2 signals

Port 6 pin LED number

P6.3 LD2

P6.4 LD3

P6.5 LD4

Pins number TP1 signals TP2 signals

CC P43

CC P42

3 RESET P41

4P37P40

5P36P17

6P35P16

7P34P15

8P33P14

9P32P13

10 P31 P12

11 P30 P11

12 P65 P10

13 P64 A7

14 P63 A6

15 P62 A5

16 P61 A4

17 P60 A3

18 P57 A2

19 P56 A1

20 P55 A0

21 P54 DSN

22 P53 ASN

23 P52 P07

24 P51 P06

25 P50 P05

26 DCD P04

27 DSR P03

28 RD P02

29 RTS P01

30 TD P00

31 CTS RI

32 DTR GND

7/17

ST92163 DEMO BOARD CHARACTERISTICS

2.2.7 I/O EXPANSION CONNECTOR

On the I/O expander (J3) it is possible to connect a daughter board to develop specific appli-

cation. On this connector all the microcontroller’s pins are available but the developer will find

too the address latch outputs (pin 45 to 52), the RS232 DB9 connector pins (pin 1 to 7 and pin

34), VCC (pin 31 and 32) and GND (pin 33).

The table 5 shows the correspondence between I/O connector pins and signals.

Table 5. I/O expansion Connector signals

Pin number Signal Pin number Signal

1A DTR 1B GND

2A CTS 2B RI

3A TD 3B P00

4A RTS 4B P01

5A RD 5B P02

6A DSR 6B P03

7A DCD 7B P04

8A P50 8B P05

9A P51 9B P06

10A P52 10B P07

11A P53 11B ASN

12A P54 12B DSN

13A P55 13B A0

14A P56 14B A1

15A P57 15B A2

16A P60 16B A3

17A P61 17B A4

18A P62 18B A5

19A P63 19B A6

20A P64 20B A7

21A P65 21B P10

22A P30 22B P11

23A P31 23B P12

24A P32 24B P13

25A P33 25B P14

26A P34 26B P15

27A P35 27B P16

28A P36 28B P17

29A P37 29B P40

30A RESET 30B P41

31A VCC 31B P42

32A VCC 32B P43

8/17

ST92163 DEMO BOARD CHARACTERISTICS

2.2.8 EXTERNAL MEMORIES

To offer you more flexibility , two external memories can be used directly with the ST92163

DEMO BOARD. To use the 32K of RAM or the 64K EPROM or FLASH ROM you just have to

put a jumper on the corresponding chip enable slot (JP2 for RAM and JP1 for EPROM/

FLASH).

The latch buffer (U4) is mandatory because the P0 port is multiplexed when you address ex-

ternal memory.

2.2.9 POWER SUPPLY CONNECTOR

The ST92163 Demo Board can be powered either through a jack allowing the use of an ex-

ternal AC/DC transformer or through the J2 connector allowing the power to be supplied from

an internal PC 5”1/4 power supply connector.

Note that by using jumper W1, you can choose to power your board from the VCC supplied by

on the on-board power supply (self power) or from the VCC supplied by the USB cable (bus

power).

Tabla de contenidos

Otros manuales de Hardware de computadora de ST

ST X-NUCLEO-AMICAM1 Manual de usuario

ST STM32G0 Manual de usuario

ST EVAL6470H-DISC Manual de usuario

ST STR91 Series Instrucciones de instalación y funcionamiento

ST B-U585I-IOT02A Manual de usuario

ST X-NUCLEO-53L5A1 Manual de usuario

ST STM32F4 Series Manual del propietario

ST STLINK-V3PWR Manual de usuario

ST X-NUCLEO-IHM03A1 Manual de usuario

ST ST32M103 Series Manual de usuario

ST Nomadik NHK-15 Manual de usuario

ST X-NUCLEO-BNRG2A1 Manual de usuario

ST STEVAL-ST25R3916B Manual de usuario

ST STM32 ODE Manual de usuario

ST X-NUCLEO-OUT04A1 Manual de usuario

ST ControlBD-7FMC2 Manual de usuario

ST X-NUCLEO-GFX02Z1 Manual de usuario

ST STDES-PFCBIDIR Manual de usuario

ST STM32F101 series Manual de usuario

ST STEVAL-ISF001V1 Manual de usuario

ST STEVAL-IFP042V1 Manual de usuario

ST STMPE2401 Manual de usuario

ST ST8034T Manual de usuario

ST X-NUCLEO-OUT06A1 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

Advantech

Advantech ASMB-935 Series Manual de usuario