Spirit XE295 Manual de usuario
XE295 Elliptical
OWNER’S MANUAL
Please carefully read this entire manual before operating your new elliptical
TABLE OF CONTENTS
1
2
3
3
4
9
11
14
20
22
23
ATTENTION
This elliptical is intended for residential use only and is warranted for this application.
Any other application voids this warranty in its entirety.
Product Registration
Important Safety Instructions
Important Electrical Instructions
Important Operation Instructions
XE295 Assembly Instructions
Features
Console Operation
Programmable Features
Using Heart Rate Transmitter
General Maintenance
Manufacturer’s Limited Warranty
XE295 Elliptical
1
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this tness product
in the space provided below.
Serial Number
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to
Spirit Manufacturing, Inc. You can also go to www.spirittness.com/warranty.asp under
the support tab to register online.
Thank you for your purchase of this quality elliptical trainer from Spirit Manufacturing, Inc.
Your new elliptical was manufactured by one of the leading tness manufacturers in the
world and is backed by one of the most comprehensive warranties available. Through your
dealer, Spirit will do all we can to make your ownership experience as pleasant as possible
for many years to come. If not purchased direct from Spirit, the local dealership where you
purchased this elliptical is your administrator for all Spirit warranty and service needs. Their
responsibility is to provide you with the technical knowledge and service personnel to make
your experience more informed and any difculties easier to remedy.
Please take a moment at this time to record the name of the dealer, their telephone number,
and the date of purchase below to make any future, needed contact easy. We appreciate
your support and we will always remember that you are the reason that we are in business.
Please complete and mail your registration card today and enjoy your new elliptical trainer.
Yours in Health,
Spirit Manufacturing, Inc.
Congratulations on your new elliptical and welcome to the Spirit family!
Name of Dealer
Dealer Phone #
Purchase Date
PRODUCT REGISTRATION
XE295_20110118
XE295 Elliptical 2
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your Spirit elliptical from the
electrical outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, re, electric shock, or injury to persons, install
the elliptical on a at level surface with access to a 110-volt, 15-amp grounded outlet
with only the elliptical plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH
ONLY ONE OUTLET ON THE END:
Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both
carpet and elliptical may result.
Keep children away from the elliptical. There are obvious pinch points and other
caution areas that can cause harm.
Keep hands away from all moving parts.
Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not
working properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, then remove the plug from
the outlet.
Do not attempt to use your elliptical for any purpose other than for the purpose it is
intended.
The hand pulse sensors are not medical devices. Their purpose is to provide you
with an approximate measurement in relation to your target heart rate. Use of a chest
transmitter strap is a much more accurate method of heart rate analysis . Various fac-
tors, including the user’s movement, may affect the accuracy of heart rate readings.
The pulse sensors are intended only as exercise aids in
determining heart rate trends in general.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for
use on your elliptical. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
XE295 Elliptical
3
WARNING!
NEVER remove any cover without rst disconnecting AC power. If voltage varies by ten
percent (10%) or more, the performance of your elliptical may be affected. Such
conditions are not covered under your warranty. If you suspect the voltage is low, contact
your local power company or a licensed electrician for proper testing.
NEVER expose this elliptical to rain or moisture. This product is NOT designed for use
outdoors, near a pool or spa, or in any other high humidity environment. The operating
temperature specication is 40 to 120 degrees Fahrenheit, and humidity is 95%
non-condensing (no water drops forming on surfaces).
IMPORTANT ELECTRICAL INSTRUCTIONS
NEVER operate this elliptical without reading and completely understanding the
results of any operational change you request from the computer.
Understand that changes in resistance do not occur immediately. Set your
desired resistance level on the computer console and release the adjustment key. The
computer will obey the command gradually.
NEVER use your elliptical during an electrical storm. Surges may occur in your
household power supply that could damage elliptical components. Unplug the
elliptical during an electrical storm as a precaution.
Use caution while participating in other activities while pedaling on your elliptical;
such as watching television, reading, etc. These distractions may cause you to lose
balance which may result in serious injury.
Do not use excessive pressure on console control keys. They are precision set to
function properly with little nger pressure.
IMPORTANT OPERATION INSTRUCTIONS
XE295 Elliptical 4
ASSEMBLY TOOLS
1. Using a razor knife (Box Cutter), cut the banding straps that
wraparound the carton, then cut around the dotted line at the bottom of
the box; lift the box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or
missing parts. If damaged parts are found, or parts are missing, contact
your dealer immediately.
3. Locate the hardware package. The hardware is separated into four
steps. Remove the tools rst. Remove the hardware for each step as
needed to avoid confusion. The numbers in the instructions that are
in parenthesis (#) are the item number from the assembly drawing for
reference.
PRE-ASSEMBLY
XE295 ASSEMBLY INSTRUCTIONS
#108. Phillips Head
Screwdriver
#107. Short Phillips
Head Screw Driver
#106. 13/14mm
Wrench
#109. 12/14mm
Wrench
XE295 Elliptical
5
1. Locate the Console Mast (12) and Console Mast Cover (41) and slide the Cover onto the Mast
as far as it will go. Make sure the Console Mast Cover (41) is facing the correct way.
2. At the top opening of the Main Frame (1), there is a Computer Cable (31) tied to a twist tie wire.
Feed the twist tie wire and Computer Cable (31) into the bottom of the Console Mast (12) and
out of the opening at the top.
3. Install the Console Mast (12) into the receiving bracket on the top of the Main Frame (1). NOTE:
there is one bolt already installed in the receiving bracket that will engage with the slot at the
bottom of the Console Mast. This needs to be tightened last, after the three other console mast
bolts.
4. Place a Split Washer (96) onto the Hex Head Bolt (60) and hand tighten through the left side of
the console mast. Place a Curved Washer (84) onto each Hex Head Bolt (103) and thread both
into the front of the console mast tube. Fasten these front bolts as tight as possible with the
wrench (106). Next rmly tighten the two left side bolts with the same wrench. NOTE: The
Computer Cable (31) runs through the Console Mast (12). Be careful not to pinch this cable
during this procedure because it may affect the electrical functions of the console.
5. Connect the two Hand pulse cables (36), Resistance cable (124), and Computer Cable (31) to
the back of the console (30). Do not force the connectors; they will only t one way and are
different sizes to prevent confusion. Store the excessive cable in the Console Mast tube (12).
6. Attach the Console (30) to the bracket of the console mast tube with four Phillips Head Screws
(66). Tighten the screws with the Phillips Head Screw Driver (108).
CONSOLE MAST ASSEMBLY
1
#96. 3/8”
Split Washer (1 pc)
#84. 3/8” x 23
Curved Washer
(2 pcs)
HARDWARE
#66. M5 x 10mm
Phillips Head
Screw (4 pcs)
#103. 3/8” x 3/4”
Hex Head Bolt
(2 pcs)
#60. 3/8” x 2-1/4”
Hex Head Bolt
(1 pc)
XE295 Elliptical 6
1. Slide two Wave Washers (81) onto both the Left and Right Console Mast axle.
2. Slide the Swing Arms (L) and (R), (10& 11) onto the appropriate side of the axle. Note: Make
sure the arms are attached as shown in the illustration.
3. Place a Flat Washer (97) onto each Hex Head Bolt (103) and fasten in the end of the left and
right axle. Tighten with the wrench (106).
4. Slide the grommet (123) onto the Resistance cable (124); connect the two Resistance cables
(124 & 125) and store the excess cable in the Console Mast tube (12) after snapping the grom-
met into the hole of the console mast tube.
SWING ARM ASSEMBLY
2
#97.3/8” x 30mm
Flat Washer (2 pcs)
#81. 25mm Wave
Washer (4 pcs)
#103. 3/8” x 3/4” Hex
Head Bolt (2 pcs)
HARDWARE
#123. Grommet
(1 pc)
XE295 Elliptical
7
1. Untie the twist tie that holds each bushing (22) to the Connecting Arm end. Align the hole in
the end of the Connecting Arms (L & R) (8 & 9) with the hole in the bracket of the Swing Arms
(L) and (R), (10 & 11). The Connecting Arm ends should be inside of the Swing Arm (L) and (R),
(10 & 11) brackets. Slide a Hex Head Bolt (104) through each Swing Arm (L) and (R), (10 &11)
bracket and each Connecting Arm end.
2. Slide a Flat Washer (80) onto each bolt, then fasten the arms together by tightening a Nyloc Nut
(71) to each bolt using the wrenches provided (109 & 106) wrenches.
CONNECTING ARM ASSEMBLY
3
#80. 5/16” x 20 x1.5T
Flat Washer
(2 pcs)
#71. 5/16”
Nyloc Nut
(2 pcs)
HARDWARE
#104. 5/16” x 1-1/4”
Hex Head Bolt
( 2 Pcs)
Otros manuales para XE295
5
Tabla de contenidos
Otros manuales de Entrenador elíptico de Spirit
Spirit
Spirit XE 195 Manual de usuario
Spirit
Spirit XE295 Manual de usuario
Spirit
Spirit CE800 Manual de usuario
Spirit
Spirit Inspire ZE40 Manual de usuario
Spirit
Spirit XE400 Manual de usuario
Spirit
Spirit Esprit EL255 Manual de usuario
Spirit
Spirit Group Exercise Elliptical Manual de usuario
Spirit
Spirit XG200e Manual de usuario
Spirit
Spirit XG400 e-Glide Trainer Manual de usuario
Spirit
Spirit CE900 Manual de usuario
Spirit
Spirit XE 195 Manual de usuario
Spirit
Spirit CE800 Manual de usuario
Spirit
Spirit XE320 Manual de usuario
Spirit
Spirit 16611608000 Manual de usuario
Spirit
Spirit E-Glide SE550 Manual de usuario
Spirit
Spirit XE895 Manual de usuario
Spirit
Spirit XE 700 Manual de usuario
Spirit
Spirit Empire SPT0045 Manual de usuario
Spirit
Spirit SE500 Manual de usuario
Spirit
Spirit XG400 e-Glide Trainer Manual de usuario
Manuales populares de Entrenador elíptico de otras marcas
Weslo
Weslo Momentum 4.0 Elliptical Manual de operación y mantenimiento
Progear Fitness
Progear Fitness Air elliptical pro 1307 Manual de usuario
Torque Fitness
Torque Fitness XPLLP Manual de usuario
Octane Fitness
Octane Fitness PRO3700C Manual de usuario
Xterra
Xterra FS5.8e Manual de usuario
Bodyguard
Bodyguard E-40 Manual de usuario
Bonn Germany
Bonn Germany Concept 2.2 Manual de usuario
Precor
Precor Resolute RSL 620 Manual de usuario
NordicTrack
NordicTrack E 9.2 Elliptical Manual de usuario
Vision Fitness
Vision Fitness X6600iNetTV Manual de usuario
Matrix
Matrix MX-A5x Manual de usuario
SportsArt Fitness
SportsArt Fitness ECO-NATURAL Elite E874 Manual de usuario
