Spirit XE526SE Manual de usuario

Service Manual

Elliptical XE526SE

Elliptical XE526SE Service Manual

Plastic Parts

Round Disk Right Handle Bar Cover (Front/Rear)

Round Disk Cover Console Pedal (R)

Side Case (R)

Left Handle Bar Cover (Front/Rear) Console Mast Cover

Pedal Arm Cover (L) Rear Stabilizer Cover (A)

Connecting Arm Cover B (R) Slide Wheel Cover Rear Stabilizer Cover (B)

Connecting Arm Cover A (L) Pedal (L)

Front Stabilizer Cover Side Case (L)

Skeleton

Cross Bar

Bushing Housing Connecting Arm (R)

Console Mast

Swing Arm (R)

Main Frame Rear Rail Assembly

Flywheel

Pedal Arm (L) Pedal Arm (R)

Drive Pulley

Connecting Arm (L) Slide Wheel

Table of Contents：

I. Replacing Parts

1. The Console

2. Swing Arms and Connecting Arms

3. Pedal Arms

4. Side Cases

5. The Cross Bar

6. The Belt

7. The Idler Wheel Assembly

8. The Flywheel

9. The Drive Pulley

10. The Bushing Housing

11. Slide Wheels

II. Troubleshooting

1. The Console

2. Side Cases and Round Disk

3. The Flywheel

4. The Drive Belt

5. Swing Arms

6. The Bushing Housing

7. Pedal Arms, Connecting Arms and Slide Wheels

III. Q＆

＆＆

＆A

1. Noises

2. Slippage

3. Plays

4. Smoothness

5. Other Problems

Model XE526SE Work Replacing Parts

The Part 1. The Console Rev.

Procedures：

1. Use Phillips head screw driver to release

four M5 x 10 mm Phillips head screws

which secure the console, then disconnect

the computer cable, handle wire (red and

white) and hand pulse cable in order to

take the console apart, as shown in

figures 1 & 2.

2. To resume, connect the computer cable,

handle wire (red and white) and hand

pulse cable with the console and tighten

four M5 x 10 mm Phillips head screws,

beware not to twist cables.

3. If taking apart the console bottom cover

is necessary, release 3.5x12 self tapping

screws, as shown in figure 3.

Model XE526SE Work Replacing Parts

The Part 2. Swing Arms and Connecting Arms Rev.

Procedures：

1. Use Phillips head screw driver to release

3.5x12 self tapping screws, which secure

handle bar covers and M5x15mm,

3.5x12 self tapping screws which secure

connecting arm covers, as shown in

figures 1 & 2.

2. Then use 12mm and 13mm wrenches to

release 5/16" x1-1/4" hex head screw,

5/16" x 20 x 1.5T flat washer and

5/16" x 7T nut, which secure the rod end

bearing, as shown in figure 3.

3. Use 12mm wrench to release

5/16" x 15m/m hex head screw and

5/16" x 23 x1.5T flat washer, which

secure the swing arm, to take it apart, as

shown in figure 4.

Model XE526SE Work Replacing Parts

The Part 2. Swing Arms and Connecting Arms Rev.

Procedures：

4. Use 12mm wrench to release

5/16" x 15m/m hex head screw and

5/16" x 20 x1.5T flat washer, which

secure the connecting arm, then release

the carriage bolt under the pedal to take

the connecting arm apart, as shown in

figure 5.

5. Release four M5x10mm Phillips head

screws, which secure the pedal, to take

the pedal from the connecting arm, as

shown in figure 6.

6. Reverse above procedures to resume

parts by returning the carriage bolt and

tightening 5/16" x 15m/m hex head

screw and 5/16" x 23 x 1.5T flat washer,

as shown in figure 7.

Model XE526SE Work Replacing Parts

The Part 3. Pedal Arms Rev.

Procedures：

1. Follow procedure 2 to take apart the

connecting arm.

2. Use M8 wrench and 14mm wrench to

release 3/8” x 2-1/4” Socket Head Cap

Bolt, two 3/8"×19×1.5T flat washers

and 3/8” x 11T nut, which secure the

pedal arm and bushing housing, and

take the pedal apart, as shown in figures

2 & 3.

3. Use 12mm wrench to release

5/16" x 15m/m hex head screw and

5/16" x 35 x1.5T flat washer and take

the bushing housing apart, as shown in

figure 4.

4. Reverse above steps to resume parts.

Model XE526SE Work Replacing Parts

The Part 4. Side Cases Rev.

Procedures：

1. Follow procedures 2 & 3 to take apart

the connecting arm and pedal arm,

respectively.

2. Slap backward the console mast cover

so that it separate from side covers, as

shown in figure 1.

3. Use Phillips head screw driver to

release seven 4x19 self tapping screws

and three 5x16 tapping screws, which

secure right side case to take it apart,

as shown in figures 2 & 3.

4. To take left side case apart, release

4x15 self tapping screws, 1/4"x19 flat

washers and three 5x16 tapping screws

on the main frame, then disconnect DC

cables, as shown in figures 4, 5 & 6.

Model XE526SE Work Replacing Parts

The Part 4. Side Cases Rev.

Procedures：

5. To resume, first connect DC cables.

6. Install left side case on the main frame,

with 5/16" x 23 x 1.5T flat washer

between the side case and the main

frame, then tighten three 5x16 tapping

screws, with the side case and round

disk at the center, and 4x15 self tapping

screws, as shown in figure 7 & 8.

7. Match right side case with left side case

and tighten with seven 4x19 self tapping

screws and three 5x16 tapping screws.

8. Follow procedures 3~4 and 2~5 to

resume the pedal arm and the

connecting arm.

Tabla de contenidos

Otros manuales de Entrenador elíptico de Spirit

Spirit

Spirit XE295 Manual de usuario

Spirit

Spirit CE800 Manual de usuario

Spirit

Spirit CE800 ENT Manual de usuario

Spirit

Spirit XE395 Elliptical Manual de usuario

Spirit

Spirit 16611608000 Manual de usuario

Spirit

Spirit Esprit EL255 Manual de usuario

Spirit

Spirit 161173195 Manual de usuario

Spirit

Spirit EL1 Manual de usuario

Spirit

Spirit XE295 Manual de usuario

Spirit

Spirit XE520s Manual de usuario

Spirit

Spirit XG400 e-Glide Trainer Manual de usuario

Spirit

Spirit Inspire ZE20 Manual de usuario

Spirit

Spirit XE850-A27 Manual de usuario

Spirit

Spirit XE400 Manual de usuario

Spirit

Spirit XE395 Elliptical Manual de usuario

Spirit

Spirit XG200 Manual de usuario

Spirit

Spirit CRS800 Manual de usuario

Spirit

Spirit CE800 Manual de usuario

Spirit

Spirit XE 195 Manual de usuario

Spirit

Spirit XE795 Manual de usuario

Spirit

Spirit 161173395 Manual de usuario

Spirit

Spirit CE900ENT Manual de usuario

Spirit

Spirit XE 125 Manual de usuario

Spirit

Spirit XE 100 Manual de usuario

Manuales populares de Entrenador elíptico de otras marcas

Weslo

Weslo Momentum 4.0 Elliptical Manual de operación y mantenimiento

Progear Fitness

Progear Fitness Air elliptical pro 1307 Manual de usuario

Torque Fitness

Torque Fitness XPLLP Manual de usuario

Octane Fitness

Octane Fitness PRO3700C Manual de usuario

Xterra

Xterra FS5.8e Manual de usuario

Bodyguard

Bodyguard E-40 Manual de usuario

Bonn Germany

Bonn Germany Concept 2.2 Manual de usuario

Precor

Precor Resolute RSL 620 Manual de usuario

NordicTrack

NordicTrack E 9.2 Elliptical Manual de usuario

Vision Fitness

Vision Fitness X6600iNetTV Manual de usuario

Matrix

Matrix MX-A5x Manual de usuario

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Manual de usuario

Sears

Sears FREE SPIRIT C249 30737 0 Manual de usuario

True

True FS-64 Manual de usuario

Sport-thieme

Sport-thieme ST 310 Manual de usuario

VIRTUFIT

VIRTUFIT CTR 1.1 Manual de usuario

Kettler

Kettler GIRO C 1 Manual de usuario

CIRCLE FITNESS

CIRCLE FITNESS E7 Manual de usuario