Sper scientific 850081DOK Manual de usuario
Dissolved Oxygen Meter Kit
850081DOK
Instruction Manual
2 3
Dissolved Oxygen Meter Kit - 850081DOK
Copyright ©2017 by Sper Scientic
ALL RIGHTS RESERVED
Printed in the USA
The contents of this manual may not be reproduced
or transmitted in any form or by any means electronic,
mechanical, or other means that do not yet exist or may
be developed, including photocopying, recording, or any
information storage and retrieval system without the express
permission from Sper Scientic.
SPER SCIENTIFIC LTD.
8281 E. Evans Rd., Suite #103
Scottsdale, AZ 85260
(480) 948-4448
3
INTRODUCTION ................................ 4
FEATURES ..................................... 5
MATERIALS SUPPLIED ........................... 5
FRONT PANEL DESCRIPTION ..................... 6
SETUP ........................................ 7
MEASURMENT FUNCTIONS ..................... 10
pH MEASUREMENTS ........................... 12
DO MEASUREMENTS........................... 15
CONDUCTIVITY MEASUREMENTS ................ 17
SPECIFICATIONS .............................. 21
PROBES ..................................... 21
ACCESSORIES ................................ 23
WARRANTY................................... 24
TABLE OF CONTENTS
4 5
INTRODUCTION
This Sper Scientic Dissolved Oxygen Meter Kit (Model
850081DOK) comes with dissolved oxygen (DO) probe
(850081DO) and also uses optional, interchangeable probes
to read pH, millivolt (mV)/ oxygen reduction potential (ORP),
conductivity, total dissolved solids (TDS), salinity, and
temperature. Order only the probes required for your current
parameters and add additional probes in the future.
Only 850081DO probe comes with this kit. Other Probes
are optional.
The meter features include readings in °C or °F, automatic
temperature compensation (ATC) and salinity and altitude
compensation for DO measurements.
Additional features include automatic shuto, minimum
and maximum values, a fold-out easel back and a tripod
mounting screw. Automatically recognizes pH buers 4, 7
and 10 for simple calibration when using optional probes
5
FEATURES
• Reads DO, and has the option to read pH, mV/ORP,
conductivity, TDS, salinity and temperature with
optional probes
• Automatic temperature compensation
• Salinity and altitude compensation for DO measurements
• Maximum and minimum values
• Hold function
• Temperature units in °C or °F
• Automatic calibration recognition of pH buers when using
optional pH probe (840016)
• Battery or optional DC 9V power adapter
• Tripod mounting screw
• Automatic shuto
• Backlight
MATERIALS SUPPLIED
• Water Quality Meter
• Instruction Manual
• DC 9V Battery
• Hard Carrying Case
6 7
1. LCD Display
2. Power/Backlight Button
3. Hold/Escape Button
4. Record Button
5. ▲/Range Button
6. ▼/Function Button
7. Set Button
8. Enter Button
9. Easel Stand
10. Battery Compartment
Cover
11. Battery Compartment
Cover Screw
12. Tripod Mounting Screw
13. Temperature Probe
Socket
14. Dissolved Oxygen
Probe Socket
15. Conductivity Probe Socket
16. pH Probe/BNC Socket
17. DC 9V Power
Adapter Socket
18. Reset Button
19. Computer Output Terminal
1.
2.
3.
4.
5. 6.
7. 8.
9.
10.
11.
12.
13.
14.15.
16.
17.
18.
19.
FRONT PANEL DESCRIPTION
7
SETUP
Meter On and O
1. Press POWER to turn the meter on.
2. Press and hold POWER for 3 seconds and release to turn
the meter o.
Backlight
The backlight will illuminate automatically when the meter is
turned on.
1. Press the backlight button to turn the backlight o.
2. Press the backlight button again to turn the backlight on.
Entering Setup Mode
1. Press POWER to turn the meter on.
2. Press SET for two seconds to enter Setup Mode.
3. Press SET to cycle through the options until the desired
parameter is displayed.
4. Press ESC at any time to exit Setup Mode.
Automatic Shuto
1. In Setup Mode, press SET until “PoFF” is displayed.
2. Press ▲ or ▼ to toggle between “Yes” (automatic shuto
is on) or “No” (disable automatic shuto).
3. Press ENTER to save the selection.
4. Press SET to continue to the next setup parameter, or
press ESC to exit Setup Mode.
8 9
Beeper
1. In Setup Mode, press SET until “bEEP” is displayed.
2. Press ▲ or ▼ to toggle between “Yes” (beeper is on) or
“No” (disable beeper).
3. Press ENTER to save the selection.
4. Press SET to continue to the next setup parameter, or
press ESC to exit Setup Mode.
Select Temperature Units
1. In Setup Mode, press SET until “t-CF” is displayed.
2. Press ▲ or ▼ to toggle between °C or °F.
3. Press ENTER to save the selection.
4. Press SET to continue to the next setup parameter, or
press ESC to exit Setup Mode.
Select DO Salinity Compensation
This feature is active in DO Mode only.
1. In Setup Mode, press SET until “SALt” is displayed.
2. The default value is 0%. Press ▲ or ▼ to adjust the upper
salinity compensation value.
3. Press ENTER to save the selection.
4. Press SET to continue to the next setup parameter, or
press ESC to exit Setup Mode.
9
Select DO Altitude Compensation in Meters
This feature is active in DO Mode only.
1. In Setup Mode, press SET until “HIGh” is displayed.
2. The default value is 0 meters. Press ▲ or ▼ to adjust
the upper altitude compensation value in increments of
100 meters.
3. Press ENTER to save the selection.
4. Press SET to continue to the next setup parameter, or
press ESC to exit Setup Mode.
Select DO Altitude Compensation in Feet
This feature is active in DO Mode only.
1. In Setup Mode, press SET until “HIGhF” is displayed.
2. The default value is 0 feet. Press ▲ or ▼ to adjust the upper
altitude compensation value in increments of 100 feet.
3. Press ENTER to save the selection.
4. Press SET to continue to the next setup parameter, or
press ESC to exit Setup Mode.
Select Conductivity Temperature Compensation Value
This feature is active in Conductivity Mode only.
1. In Setup Mode, press SET until “PEr C” is displayed.
2. The default value is 2% per ° C. Press ▲ or ▼ to adjust
the upper temperature compensation value.
3. Press ENTER to save the selection.
4. Press ESC to exit Setup Mode.
10 11
Select pH Manual Temperature Compensation Value
This feature is active in pH Mode only.
1. In Setup Mode, press SET until “t-SEt” is displayed.
2. The default value is 25° C / 77° F. Press ▲ or ▼ to adjust
temperature compensation value.
3. Press ENTER to save the selection.
4. Press ESC to exit Setup Mode.
System Reset
If the meter appears unresponsive or pressing the keys
produces no result, reset the system:
1. With the meter on, open the cover on the side of the meter.
2. Use a pin or the end of a paperclip to press RESET.
MEASUREMENT FUNCTIONS
Select Function (Mode)
1. Press POWER to turn the meter on.
2. Press FUNCTION to cycle through the available modes
until the desired function is displayed:
• PH
• OrP – oxidation-reduction potential
• do – dissolved oxygen
• O2 - oxygen
• Cd - conductivity
• tdS – total dissolved solids
• SALt – salinity
Tabla de contenidos
Otros manuales de Instrumento de medición de Sper scientific
Sper scientific
Sper scientific 800048 Manual de usuario
Sper scientific
Sper scientific 850045 Manual de usuario
Sper scientific
Sper scientific 840005 Manual de usuario
Sper scientific
Sper scientific 860041 Manual de usuario
Sper scientific
Sper scientific 840018 Manual de usuario
Sper scientific
Sper scientific 850024 Manual de usuario
Sper scientific
Sper scientific 840087 Manual de usuario
Sper scientific
Sper scientific 840020 Manual de usuario
Sper scientific
Sper scientific 840018 Manual de usuario
Sper scientific
Sper scientific 850011 Manual de usuario
Sper scientific
Sper scientific 840003 Manual de usuario
Sper scientific
Sper scientific 800100 Manual de usuario
Sper scientific
Sper scientific 840064 Manual de usuario
Sper scientific
Sper scientific 900019 Manual de usuario
Sper scientific
Sper scientific 800111 Manual de usuario
Sper scientific
Sper scientific 840065 Manual de usuario
Sper scientific
Sper scientific 840012 Manual de usuario
Sper scientific
Sper scientific 800046 Manual de usuario
Sper scientific
Sper scientific 840063 Manual de usuario
Sper scientific
Sper scientific 800012 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario