Speco HT-INTB1 Manual de usuario
Intensifier Series
Camera
HT-INTB1
HT-INTB2
Please read this manual thoroughly before operation and keep
it handy for further reference.
200 New Highway
Amityville, NY 11701
631-957-8700
www.specotech.com
Package Contents Operating Your Camera
Troubleshooting
3
35~36
1 2
Contents
* SET UP --------------------------------------------------------------11~12
* SET UP LENS ------------------------------------------------------13~14
* SHUTTER SPEED CONTROL ----------------------------------15~18
* BACK LIGHT--------------------------------------------------------------19
* AUTO GAIN (AGC) -----------------------------------------------------20
* WHITE BALANCE --------------------------------------------------21~22
* REDUCE NOISE---------------------------------------------------------23
* INTENSIFIER-------------------------------------------------------------24
* CAMERA TITLE-------------------------------------------------------25~26
* DAY/NIGHT/SYNC----------------------------------------------------27~28
* MOTION DETECTION-----------------------------------------------29~30
* PRIVACY-------------------------------------------------------------------31
* REVERSE------------------------------------------------------------------32
* DETAIL----------------------------------------------------------------------33
* DEFAULT/RETURN-----------------------------------------------------34
Precautions 4
Camera Installation 5
Focusing 6
Features 7~8
------------------------9
Specifications / Dimensions 37~38
Warranty 39
PRECAUTIONS
PACKAGE CONTENTS
Please make sure that the following items are included
in the package:
1 HT-INTB CAMERA
1 SUNSHIELD
1 REMOTE CONTROLLER
1 IR RECEIVER
4 MOUNTING SCREWS
1 M2.6 WRENCH (“L" TYPE)
1 VIDEO TEST CABLE
1 POWER CABLE ADAPTOR (for optional use)
Please leave this manual with the end-user for future
reference.
TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE
USE PROPER POWER CABLE
INSTALLATION SHOULD BE PERFORMED BY QUALIFIED
PERSONNEL
PLEASE USE A UL APPROVED REGULATED 24 VOLT AC
OR 12 VOLT DC POWER SUPPLY
PLEASE USE APPROPRIATE LOW VOLTAGE POWER
CABLE TO PREVENT FIRE OR ELECTRICAL SHOCK.
PLEASE INSURE THAT YOUR INSTALLATION AREA CAN
SUPPORT THE WEIGHT OF THE CAMERA.
PLEASE HANDLE THIS CAMERA CAREFULLY:
- DON’T USE A STRONG OR ABRASIVE DETERGENT WHEN
CLEANING THE CAMERA.
- USE A SOFT TISSUE OR LENS CLOTH TO CLEAN THE
FRONT GLASS
- DON’T EXPOSE THE CAMERA TO DIRECT SUN
3 4
CAMERA INSTALLATION
CONNECT POWER CABLE
1. WHEN USING 12 VOLTS DC (constant voltage 600 mA)
2. WHEN USING 24 VOLTS AC (40 Volt Amps)
3. CONNECT VIDEO CABLE
-CONNECT BNC CABLE TO THE BNC JACK.
POWER SUPPLY
CONNECT
YELLOW:VIDEO OUT
CONNECT
BLACK:(-)
POWER RED(+)
POWER SUPPLY
FOCUSING
1. SET THE ZOOM OR FIELD OF VIEW BY USING THE
ZOOM CONTROLLER (3-9mm or 5~50mm)
SET THE FOCUS BY USING THE FOCUS CONTROLLER.
LOCK BOTH RINGS INTO POSITION USING THE SET-
SCREWS.
▣3~9 mm ▣5~50 mm
5 6
♣SLC
When the image is in front of strong background lighting,
your camera allows you to get the best image.
♣INTENSIFIER
1/3 inch high density CCD and digital processor permit
high quality pictures to be captured in very low light
conditions.
♣High Resolution
Horizontal resolution of 530 TV lines is
achieved by using a SONY Double Speed CCD with
410,000 pixels, yielding pictures with a high S/N ratio.
♣Motion Detection
Built in motion detector with adjustable areas of coverage will
flash a warning on the screen when motion is detected.
♣Dynamic Noise Reduction
The Intensifier camera has a DSP chip that can
remove image noise efficiently showing clean
images in low light conditions.
♣ELECTRONIC DAY / NIGHT
The Intensifier camera can show color pictures in all lighting
conditions, or you can have it automatically switch to a B/W
picture in low light conditions
♣MANUAL / AUTO IRIS LENS
The Intensifier camera will work with auto iris,manual iris and
fixed iris lenses.
♣OSD
All camera functions are menu driven for ease of use.
7 8
Features
SET UP MENU
◈Function
LENS OPTION
●DC ●MANUAL
SHUTTER
●OFF ●F/L ●MANUAL
WHITE BALANCE
●ATW ●AWC MANUAL●
SLC – ( Speco Light Compensation )
●OFF ●LOW ●MIDDLE ●HIGH
Auto Gain
●OFF ●LOW ●MIDDLE ●HIGH
REDUCE NOISE
●OFF ●LOW ●MIDDLE ●HIGH
INTENSIFIER
●AUTO ●OFF
NEXT PAGE
●CAMERA TITEL ●DAY/NIGHT ●SYNC
●MOTION ●PRIVACY ●REVERSE
●DETAIL ●DEFAULT ●PAGE 1
EXIT
9
Operating your camera
10
11 12
When you call Camera Address
01
->Push 0 Button
->Push 1 Button
->Push CAM Button
Power Connector
(DC12V in)
485(+),(-)
Baud Rate Setting
Buzzer On/Off
Operating your camera
1. When controlled by RS-485, Pelco-D protocol (Option), refer to the
following.
A. DIP Switch Setting on the Camera
(Factory default : Camera Address = 01, Baud Rate = 2400bps)
B. Receiver Setting to use with IR Remote Controller
(Factory default : Baud Rate = 2400bps, Chart is same as
above)
C. System Integration
D. IR Remote Controller
- Can call and control each camera on the monitor by the following.
•Up to 15 Cameras can be
controlled by 1 IR Remote
Controller & 1 Receiver. You
must set up each camera’s
address by DIP Switches for
proper addressing.
Multiplexer
CCD Camera
Monitor
SET / Menu buttonUP button
DOWN
button
RIGHT button
LEFT button
Receiver
IR Remote
Controller
485(+)
485(-)
①②
RS485 Address Set
①
RS485 Baud rate Set
②
•Please Observe Polarity!
Operating your camera
1. Press the SET button to access the SETUP mode.
●SETUP menu is displayed on the monitor screen.
2. Select the desired feature using the UP or DOWN buttons.
●Each time you press the UP or DOWN button, the arrow
indicator moves up or down.
●Move the arrow indicator to the desired feature item.
3. Change the status of the selected feature using the LEFT
or RIGHT button.
4. When completed, move the arrow indicator to ‘EXIT’ and press
the SET button.
•●You can access the submenu by using SET button.
•●For the mode with ’---’, you may not access submenu.
13 14
Notes
Operating your camera - LENS
1) Setting up the LENS
Select the lens pressing the RIGHT button.
①On the SETUP menu screen, move the arrow indicator to the lens
using the UP or DOWN button.
②Select the desired feature using the LEFT or RIGHT button.
▶When DC LENS is selected, press SET button to control
the BRIGHTNESS.
●AUTO IRIS LENS (DC TYPE) is recommended
Notes
15 16
Operating your camera – SHUTTER SPEED CONTROL①
2) Shutter status and speed control
You can control brightness of the screen by the shutter speed.
①Press the SET button to display the setup menu and move the arrow
indicator to ‘SHUTTER’ using the UP or DOWN button.
②Set ‘SHUTTER’ to the desired mode using the LEFT or RIGHT
button.
▶OFF : Deactivation
▶FLK (1/100) : Flicker mode
Otros manuales para HT-INTB1
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de Speco
Speco
Speco O8VB2 Manual de usuario
Speco
Speco CVC-3805TP Manual de usuario
Speco
Speco CVC-5715DNVW Manual de usuario
Speco
Speco O4FT2 Manual de usuario
Speco
Speco CVC-6146HR Manual de usuario
Speco
Speco ProVideo CVC-870EX Manual de usuario
Speco
Speco CVC61HRB Manual de usuario
Speco
Speco CVC-5815DNV Manual de usuario
Speco
Speco HT-7048IRVF Manual de usuario
Speco
Speco O4D9 Manual de usuario
Speco
Speco VL-64TP Manual de usuario
Speco
Speco O8FT1W Manual de usuario
Speco
Speco O2D60M Manual de usuario
Speco
Speco H4FB1 Manual de usuario
Speco
Speco VLBT5W Manual de usuario
Speco
Speco O4DM Manual de usuario
Speco
Speco O2VLD7J Manual de usuario
Speco
Speco O8VT3M Manual de usuario
Speco
Speco O4VT1 Manual de usuario
Speco
Speco LPRB922 Manual de usuario
