Specialized SpeedZone Manual de usuario

SPEEDZONE COMP CYCLOCOMPUTER

Congratulations on your purchase! You are now the owner of the world’s

finest cyclocomputer. Your Specialized®SpeedZone®Comp features

a revolutionary new display screen that allows you to view five functions

simultaneously. Additionally, it has been designed to provide the best

combination of performance, features, durability and ease of use.

This illustration describes the screen display and buttons:

Km/h

TOP Button

Average Speed Needle

(Flashing)

Speed Indication Bezel

Digital Display Area

Wheel Indicator

SET Button

Current Speed Needle

Analog Clock

Maximum Speed Needle

Dot-Matrix Display Area

MPH or KM/H Indicator

MODE Button

The following functions are available

on your SpeedZone Comp:

• SPEED – Current Speed

• AVSPD – Average speed

• MXSPD – Maximum Speed

• ODO – Odometer (total distance)

• TRIP – Trip Distance

• ATM – Automatic Start/Timer

• TIMER – Stopwatch With Lap-timer

• INT – Interval Timer

• DIST – Distance Countdown

• Digital 12/24 Hour Clock

• Analog Clock

This computer also features:

• Five function LCD Display

• Easy Calibration Mode

• Heavy-duty abrasion resistant

pick-up wire.

• Water-resistant housing

• 1 Year Warranty

What is included in your SpeedZone

Comp package:

1. SpeedZone Computer (1)

2. SpeedZone CR-2032 Lithium

Battery (1)

3. SpeedZone Battery Door (1)

4. Mounting bracket (1)

5. Speed Sensor Wire (1)

6. Magnet with screw (1)

7. Adhesive backed magnet

8. Cable tie wraps (4)

9. Mounting bracket sizing straps (3)

BATTERY INSTALLATION

AND REPLACEMENT

Before using your SpeedZone Comp

Computer you will need to install the

battery. Turn the computer over so

the display is facing downward. Use

a coin to unthread the battery cap

from the computer. Install the battery

(model CR2032, Specialized P/N

481-3004) with the positive pole (+)

facing upward. Carefully thread the

battery cap back onto the case with

a coin. (See Figure 3) If, after battery

replacement, the LCD display is blank

or shows incomplete digits, turn the

computer over and press the “AC”

button on the bottom of the case with

the tip of a pen or a paper clip. This

will clear all the data and re-start the

computer. If you

need to replace

the battery,

make a note of

your odometer

reading and

wheel circum-

ference settings

before remov-

ing it. You can then re-enter the data

when you restart the computer.

MOUNTING

THE SPEEDZONE COMP

The SpeedZone Comp wheel sensor

can mount on the right or the left side

of the fork blade. Use the cable tie

wraps provided to position the sensor.

Do not tighten until the final place-

ment of the sensor magnet is correct.

(See figure 4). Wheel magnets have

been provided for both traditional

round spokes and bladed (flat) aero-

dynamic spokes.

Cable

Tie

Wraps

Sensor

Brake

Cable

FIGURE 4.

SENSOR

PLACEMENT

CR2032 battery

FIGURE 3.

Sensor

Magnet

1/32-1/16 in.

1-2 mm

Sensor

Front

Wheel

FIGURE 5.

MAGNET

PLACEMENT

For wheels with round spokes:

Attach the magnet to a spoke across

from the transmitter with the magnet

screw. The clearance between the

magnet and the transmitter should be

approximately 1/32”-1/16” (1-2mm).

Tighten the magnet and transmitter.

Do not over-tighten the magnet screw.

(See figure 5).

For wheels with bladed spokes:

Use some isopropyl (rubbing) alcohol

or a mild detergent to thoroughly

clean the spoke that you plan to attach

the magnet to. Remove the backing

from the adhesive tape and firmly

press the magnet onto spoke. The tape

uses a special pressure sensitive adhe-

sive. To ensure a strong bond, please

wait at least 12 hours for the adhesive

to cure before riding your bicycle.

Your SpeedZone Comp comes pre-

configured with a strap to fit standard

road and mountain bike handlebars.

Attach the mount to the handlebar

using the Philips head screw provided.

Tighten so that the bracket cannot

rotate on the handlebar. There are

several sizing shims provided to fit

different diameter bars. If you are

FIGURE 6. STRAP INSTALLATION

using the new 31.8mm diameter bars,

you will need to purchase the 31.8mm

Handlebar Mount Kit (Specialized

P/N 4812-3100) from your

Specialized dealer. To install the

31.8mm diameter strap onto your

SpeedZone Comp, remove the two

Philips head screws from the bottom

of the computer and push out the

retaining pin with a small screwdriver

or a straightened paperclip. (See fig-

ure 6) Use caution not to lose the pin

once you have removed it. Install the

other mounting strap and reinsert the

pin and screws. To test for proper

installation of the magnet, transmitter

and computer, activate the computer

by pushing the ‘MODE’ (right side)

button. Pick up the front of the bicycle

and spin the front wheel. The “wheel

option” indicator will flash. If it does

not flash, check the sensor and mag-

net alignment. Realign as necessary

until the “wheel option” indicator

flashes while spinning the wheel.

OPERATION AND

PROGRAMMING

When your SpeedZone Comp has

not detected any speed input for 30

minutes, it will enter sleep-mode in

order to conserve battery power.

During sleep mode only the analog

and digital clocks are displayed. The

computer will wake up as soon as

wheel speed is detected. Additionally,

you can wake it up by pushing the

“MODE”, “SET” or “TOP” button

once. In order to operate your com-

puter it must be placed in various

“modes” (i.e. odometer mode, dis-

tance mode). The computer can be

cycled through these modes by press-

ing the “MODE” button located on the

right-hand side of the housing. There

are nine cycling modes available:

1) Speed Mode, 2) Average Speed

Mode, 3) Maximum Speed Mode,

4) Odometer Mode, 5) Trip Distance

Mode, 6) Auto-timer Mode,

7) Stopwatch Mode, 8) Interval Timer

Mode and 9) Distance Countdown

Mode. Once you familiarize yourself

with the mode selection operation

you will find it very easy to navigate.

The following flowchart outlines the

mode/side-mode sequence.

Once a particular mode has been

entered, its values can be reset or

adjusted by pressing and holding the

“SET ” button for three seconds. Some

operations may require that you use

a combination of the “MODE” and

“SET” and “TOP” buttons.

1. Setting the Display Language

Your SpeedZone Comp can display

information on the dot-matrix display

area in six different languages:

English (ENGL), German (GER), French

(FR), Italian (ITA), Dutch (NED), and

Spanish (ESP). To select your language,

depress hold the “MODE”, “SET” and

“TOP” buttons simultaneously for three

seconds. The selected language will

be displayed. Use the “MODE” button

to scroll through the languages. When

the selected language is displayed

(default language is English), press the

“SET” button once to confirm your selec-

tion and exit display language mode.

2. Miles or Kilometers selection

(English only)

Your SpeedZone Comp will record

distance and speed in either miles

(m & m/h) or kilometers (K & Km/h).

Please note that miles can only be

selected when the language setting is

English. All other languages display

only kilometers. (See “Setting the

Display Language” above). To enter

your selection of miles or kilometers,

push the “MODE” button until ODO

appears on the left side of the display

(This is called the odometer mode).

Note: if your display says TRIP, press

the “SET” button once to change to

ODO. Next, hold down the “SET”

button for three seconds. The “Km”

or “m” indicator will begin blinking.

You may now alternate between

miles and kilometers by pressing the

“MODE” button. When the correct

choice is flashing, select it by pressing

the “SET” button. You will now enter

the “Programmable Odometer”

mode. If the odometer setting is

correct push the “SET” button five

times to exit odometer mode. (Other-

wise, see “Setting the Programmable

Odometer” below).

Note: The Speed Indication Bezel

will indicate 0-45MPH on SpeedZone

Comp computers purchased in the

USA and the U.K. and 0-90 Km/h

on computers purchased in all other

countries. Cyclists in the USA and the

U.K. who would like to display their

speed and distance data in kilometers

will have to multiply the value of the

numbers on the face of the bezel

by two. For example, if the Speed

needle is pointing to the 20 on the

bezel, your actual speed is 40Km/h.

3. Setting the Programmable

Odometer

This mode is useful if you have

replaced the battery and would like

to retain the mileage you have already

ridden. To access the Programmable

odometer mode, first advance to the

Odometer Mode by pressing “MODE”

button until ODO appears on the left-

hand side of the screen. Note: if your

display says TRIP, press the “SET”

button once to change to ODO.

Hold down the “SET” button for three

seconds (If you have selected English

language, the Km/h indicator will

flash. If the Km/h setting is correct

press the “SET” button once) and a

five-digit number will appear. You are

now in the programmable odometer

mode. To enter a mileage into the

odometer, press the “MODE” button

until the flashing digit is correct.

Km/h

FIGURE 7. ODOMETER SCREEN

(Note: The “MODE” button may be

held to scroll to the correct digit.) Press

the “SET” button to select the next digit

to the right. Repeat this process until

all five digits are entered as your

existing mileage. (See figure 7)

4. Wheel Circumference Selection

To set the circumference for the type

of tires you are using, you can use

Specialized’s “Easy Calibration Mode”

or measure your actual tire circumfer-

ence by the rollout method. Two

different tire diameters may be

entered by using the computer’s

“Second Wheel Option.”

Easy Calibration Mode

Your SpeedZone Comp has been

preprogrammed with the following

14 Specialized tire sizes:

26 X 1.0 26 X 2.2

26 X 1.25 650c X 20

26 X 1.5 700c X 20

26 X 1.9 700c X 23

26 X 1.95 700c X 26

26 X 2.0 700c X 32

26 X 2.1 700c X 38

When using Easy Calibration Mode,

the SpeedZone Comp will display

the tire size on its LCD display screen.

(See figure 8) The Easy Calibration

Mode is accessed by entering the

Speed (SPEED) mode and holding

down the “SET” button for three sec-

onds. The display will now show the

Otros manuales para SpeedZone

Tabla de contenidos

Otros manuales de Accesorios para bicicletas de Specialized

Specialized

Specialized TERO EQ KIT Manual de usuario

Specialized

Specialized SpeedZone Elite Manual de usuario

Specialized

Specialized AFR E100 Manual de usuario

Specialized

Specialized SpeedZone P-Brain Manual de usuario

Specialized

Specialized Transition Carbon-All Models Manual

Specialized

Specialized SPEEDZONE SPORT DOUBLE WIRELESS Manual de usuario

Specialized

Specialized AFR Rear Shock EPA Manual de usuario

Specialized

Specialized SpeedZone Sport Manual de usuario

Specialized

Specialized SPEEDZONE SPORT CYCLOCOMPUTER Manual de usuario

Specialized

Specialized Stumpjumper Adjustable Dropout Manual de usuario

Specialized

Specialized Roval Rapide Wheelset None Manual de usuario

Specialized

Specialized Rockhopper Adjustable Dropout RH Dropout Manual de usuario

Specialized

Specialized Speedzone Sport CR2032 Manual de usuario

Specialized

Specialized HPRT-0027 Manual de usuario

Specialized

Specialized FireBalls Comp Manual de usuario

Specialized

Specialized Globe Haul ST Wheel Protector Manual de usuario

Specialized

Specialized Turbo Comp Manual de usuario

Specialized

Specialized SpeedZone Manual de usuario

Specialized

Specialized SPEEDZONE II Manual de usuario

Specialized

Specialized Turbo Elite Manual de usuario

Specialized

Specialized Speedzone Comp Manual de usuario

Specialized

Specialized Command Post Adjustable Height Seat Post Manual de usuario

Specialized

Specialized Snell Helmet Manual de usuario

Specialized

Specialized Turbo Pro 23A Manual de usuario

Manuales populares de Accesorios para bicicletas de otras marcas

Sigma

Sigma BC 16.16 Manual de usuario

Playcore

Playcore Dero Setbacks Manual de usuario

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manual de usuario

Cateye

Cateye RAPID X2 Manual de usuario

buratti meccanica

buratti meccanica Clorofilla Trail Manual de usuario

Shimano

Shimano SG-8R20 Instrucciones de funcionamiento

BOB

BOB YAK Manual de usuario

APLIC

APLIC 303303/20190717TW012 Manual de usuario

SRAM

SRAM AXS BlipBox Manual de usuario

Garmin

Garmin EDGE 500 Manual de usuario

Shimano

Shimano FD-RX810 Manual de usuario

Cateye

Cateye V2C - Manual de instrucciones

KMART

KMART 43115907 Manual de usuario

SIGMA SPORT

SIGMA SPORT Buster 2000 Manual de usuario

NVO Components

NVO Components STEM Manual de usuario

DAXYS

DAXYS BP188 Manual de usuario

XLC

XLC BV-W17 Manual de usuario

Deda Elementi

Deda Elementi SUPERBOX Manual de usuario