SnowEx SP-575V Manual del propietario

FOR MODELS

SP-575V Serial # B3-100000 and higher

Madison Heights, Michigan 48071

800-725-8377

www.snowexproducts.com

Customer Copy

This Manual Must Be Read Before Operating The Equipment

Owner / Operator’s Manual

Table of Contents

General Information ...................................................................................................................................................................................... 3

Introduction ................................................................................................................................................................................................. 4

Safety .......................................................................................................................................................................................................... 5

Operating the Spreader ................................................................................................................................................................................ 6

Spreader Maintenance ................................................................................................................................................................................. 7

General Wiring Instructions .......................................................................................................................................................................... 8

Control and Harness Diagram ................................................................................................................................................................. 9-11

Trobleshooting ...................................................................................................................................................................................... 12-13

Warranty .................................................................................................................................................................................................... 14

Spreader Views

Model # SP-575V......................................................................................................................................................................... 15

Frame Assembly Parts Breakdown

Model # SP-575V.................................................................................................................................................................... 16-17

Drive Assembly Parts Breakdown

Model # SP-575V.................................................................................................................................................................... 18-19

Notes .................................................................................................................................................................................................... 20-21

Have a question or need assistance?

SnowEx Customer Care

(800) 725-8377

or (248) 586-3500

Monday through Friday 8:00 AM to 4:30 PM EST

Fax: (248) 691-8378

E-Mail: customercare@trynexfactory.com

Website: www.snowexproducts.com

General Information

CONGRATULATIONS!

The spreader you have purchased is an example of snow and ice control technology at its nest! Your spreader’s self-contained design is a

trademark of all SnowEx products. Here’s why…

SIMPLICITY: Fewer moving parts manufactured of higher quality means minimal maintenance for your SnowEx spreader.

RELIABILITY: High impact linear low density polyethelyne hopper. State-of-the-art electronic dual variable speed control, custom engineered

powder coated frame, maximum torque 12-volt motor coupled to a custom engineered transmission; found only on SnowEx products.

VERSATILITY: Multi-use capabilities allows spreading of a variety of materials for snow and ice control.

WARRANTY: Best in the industry, hands down! 2 years standard and now 5 year extended (optional).

The benets you are about to recognize are that of time, money and effort.

We welcome you to the world of SnowEx Performance.

Registration

Record the following information in this manual for quick reference.

Spreader Model Number

Spreader Serial Number

Handheld Control Pendant Serial Number Control Board Serial Number

Date of Purchase

Dealer Where Purchased

When ordering Parts, the above information is necessary. This will help to see that you

receive the correct parts.

At the right is a diagram of the ID tag. This tag on the spreader is located on the frame.

Please ll out the warranty card with all the necessary information to validate it.

This will also give us a record so that any safety or service information can be

communicated to you.

SP-575V

B3-100000

SP-1075V

C3-100000

Introduction

This manual has been designed for your help. It will assist you and instruct you on the proper set-up, installation and use of this spreader.

Refer to the table of contents for an outline of this manual.

We require that you read and understand the contents of this manual completely (especially all safety information) before attempting any

procedure contained herein.

THIS SIGN SHOULD ALERT YOU:

The Society of Automotive Engineers has adopted this SAFETY ALERT SYMBOL to pinpoint characteristics

that, if NOT carefully followed, can create a safety hazard. When you see this symbol in this manual or on the

machine itself, BE ALERT! Your personal safety and the safety of others is involved.

Dened below are the SAFETY ALERT messages and how they will appear in this manual:

(RED)

Information that, if not carefully followed,

can cause death!

(ORANGE)

Information that, if not carefully followed,

can cause serious personal injury or death!

(YELLOW)

Information that, if not carefully followed,

can cause minor injury or damage to equipment

Examples of Warning Decals To Indicate Operational Awareness

D6192_Warning.ai4in x 2.25in

D6194_Warning.ai4in x 2.25in

Safety

Before attempting any procedure in this book, these safety instructions must be read and understood by all workers who have any part in the

preparation or use of this equipment.

For your safety warning and information decals have been placed on this product to remind the operator of safety precautions . If anything

happens to mark or destroy the decals, please request new ones from SnowEx.

Remember, most accidents are preventable and caused by human error. Exercising of care and precautions

must be observed to prevent the possibility of injury to operator or others!

Never operate equipment when under the inuence of alcohol, drugs, or medications that might alter your

judgment and/or reaction time.

Before working with the spreader, secure all loose tting clothing and unrestrained hair.

Always wear safety glasses with side shields when servicing spreader. Failure to do this could result in

serious injury to the eyes.

Never allow children to operate or climb on equipment.

Always check areas to be spread to be sure no hazardous conditions or substances are in the area.

Always inspect unit for defects: broken, worn or bent parts, weakened areas on spreader.

Remember it is the owner’s responsibility to communicate information on safe usage and proper

maintenance of all equipment.

Always make sure personnel are clear of areas of danger when using equipment.

Never weld or grind on equipment without having a re extinguisher available.

Inspect the unit periodically for defects. Parts that are broken, missing or worn out must be replaced

immediately. The unit or any part of it can not be altered without prior written permission from the

manufacturer.

Always inspect pins and latches whenever attaching or detaching spreader, and before operation of spreader.

Never exceed 45 m.p.h. when loaded spreader is attached to vehicle. Braking distances may be increased

and handling characteristics may be impaired at speeds above 45 m.p.h.

Never use wet materials or materials with foreign debris with any of these spreaders. These units are

designed to handle dry, clean, free owing material.

Never leave material in hopper for long periods of time. Be aware that all ice melters are hygroscopic and will

attract atmospheric moisture and harden up.

Operating the Spreader

Model # SP-575V

SPREADER LOADING

WARNING – Do not overload vehicle. Use chart below to calculate weight of material. Weights of material are an average for dry

materials.

Material Weight Per Cubic Ft.

Rock Salt 80-90 lbs.

Sand/Salt Mix 95-120 lbs.

• Warning – Never leave material in hopper for long periods of time as salt is hygroscopic and will attract atmospheric moisture and harden up.

When spreading sand mix, a 1:1 ratio for Sand/Salt mix is recommended to prevent the material from freezing.

SPREADER OPERATION

• The variable speed controller has nger-tip dial action, digital system status with warning protection and blast feature.

• To start, press On/Off button on Control Pendant. Press Start/Stop button and Spinner will accelerate to speed set on dial.

• To stop, press Start/Stop button. Press On/Off button to turn off Spreader

• Adjust speed of Spinner using dial in center of Control Pendant

• If more material is needed in certain areas, press the Blast button to give maximum power.

SPREADING TIPS

• Spread ice melters with the storm to prevent unmanageable levels of ice.

• Never exceed 10 miles per hour when spreading.

• For a wider pass, increase spinner speed.

• For a heavier pass, drive slower.

• Never operate spreader near pedestrians.

• Calculate spread pattern when near vegetation.

LICENSE PLATE INSTALLATION (IF REQUIRED BY LOCAL LAWS)

• You will need (2) 1/4-20 X 1/2” machine screws along with nylock type nuts (not included with spreader)

• Install license plate to mounting holes provided in hopper apron (see illustration below)

Mounting Holes

Spreader Maintenance

Model # SP-575V

• WARNING – When servicing is necessary, perform it in a protected area Do not use power tools in rain or snow because of danger of electrical

shock or injury. Keep area well lighted. Use proper tools. Keep the area of service clean to help avoid accidents.

• WARNING: Never remove spreader with material in hopper.

• WARNING: Disconnect electricity to spreader before servicing.

• CAUTION: – When replacing parts use only original manufacturer”s parts. Failure to do so will void warranty.

• CAUTION: – The controller is a solid state electronic unit and is not serviceable. Any attempt to service will void warranty.

• CAUTION: - There are no serviceable parts in the motor/transmission assembly. Any attempt to service will void warranty.

• CAUTION: - Spinner motor is not designed for continuous duty. Allow motor to cool between long cycle times.

• CAUTION: – When pressure washing motor enclosure area, stay at least 36’’ away from motor enclosures.

• ATTENTION: Store control in cool dry place during the off season.

• Use dielectric grease on all electrical connections to prevent corrosion at the beginning and end of the season and each time power plugs are

disconnected.

• Wash unit after each use to prevent material build-up and corrosion.

• Paint or oil all bare metal surfaces at the end of the season.

• Apply small amount of light oil to latches as needed.

• If motor cover is removed for any reason, use silicone sealant to ensure weather proong of enclosure.

• After rst use, tighten all nuts and bolts on spreader and mount.

General Wiring Instructions

Model # SP-575V

Step 1: Route Vehicle Harness Assembly and route from the rear of vehicle to front. Route harness along frame and attach to frame holes and

frame supports. It is not recommended to attach to fuel or brake lines for obvious reasons. Do not route close to exhaust system or

engine, even though Snowex uses high temperature wiring, it still could melt under extreme heat and short the spreader electrical

system, as well as the vehicle electrical system.

Step 2: Mount rear plug on bumper using supplied bolts, locate towards the center of the bumper to reduce the amount of debris it catches from

the tires. Important: Apply a small amount of dielectric grease to the plug.

Step 3: Secure harness from the rear to the front using heavy duty ty-wraps or frame clips along the frame and lighter duty ty-wraps everywhere

else.

Step 4: Find a location along the rewall where the Control Module can be attached. Mount Control Module to rewall with included hardware.

Step 5: Connect Harness to Control Module and to Vehicle Battery.

Step 6: Drill a hole in the rewall or use an existing hole; Route Data Cable from Control Module into the cab. Secure as needed to prevent the

Data Cable getting caught in moving parts.

Step 7: Plug Control Pendant into Data Cable. Push “ON” Button to test for power.

Step 8: Stick Hook-and-Loop (“Velcro”) to back of Pendant and to Dash.

Control Diagram

Model # SP-575V

F50574 Control Pendant

F50596 Spreader Control

IMPORTANT: Do Not modify harness length. Any modications will void warranty.

Special Notes:

1) All external connections must have dielectric grease.

2) Read lead labels before attaching to power source or ground.

3) No other devices may be spliced into wiring harness.

4) Any repairs to wiring harness must be done with heat shrink butt connectors.

Harness Diagram

Model # SP-575V

120”

Load View

White

Black Red

Green

F50578 Data Cable

F50601 Battery Harness

4.88 15

105.00 6

123

125

MODULE END

BATTERY END

Tabla de contenidos

Otros manuales de Esparcidor de SnowEx

SnowEx

SnowEx V-Maxx G2 Manual de usuario

SnowEx

SnowEx SP-225-1 Instrucciones de funcionamiento

SnowEx

SnowEx VX-6010 Manual de usuario

SnowEx

SnowEx Vee Pro 3000 Manual de usuario

SnowEx

SnowEx V-Maxx G2 VX-6010 Manual de usuario

SnowEx

SnowEx SP-8550 Manual del propietario

SnowEx

SnowEx Drop Pro 600 Manual de usuario

SnowEx

SnowEx SP-9500X Manual de usuario

SnowEx

SnowEx SP-85 Instrucciones de funcionamiento

SnowEx

SnowEx VX-1500 Manual de usuario

SnowEx

SnowEx V-Pro 32200 Manual de usuario

SnowEx

SnowEx SP-2200 Manual de usuario

SnowEx

SnowEx Precision Pro SP-1675 Manual de usuario

SnowEx

SnowEx SP-2400 Manual del propietario

SnowEx

SnowEx HELIXX Manual de usuario

SnowEx

SnowEx VX-4200 Manual de usuario

SnowEx

SnowEx HELIXX Series Manual de usuario

SnowEx

SnowEx V-Pro 32300 Manual de usuario

SnowEx

SnowEx Bulk-Pro 1875 Manual de usuario

SnowEx

SnowEx SP-1675 Manual de usuario

SnowEx

SnowEx V-Pro 32300 Manual de usuario

SnowEx

SnowEx SP-9300 Manual de usuario

SnowEx

SnowEx HELIXX Manual de usuario

SnowEx

SnowEx K1-131116 Manual del propietario

Manuales populares de Esparcidor de otras marcas

PEQUEA

PEQUEA GT-100 Manual de usuario

Herculano

Herculano H2RS9 Manual de usuario

Epoke

Epoke SKE8 Manual de usuario

GEA

GEA EL44 Hoja de especificaciones

Boss Snowplow

Boss Snowplow TGS 800 Manual de usuario

Fisher

Fisher EMERSON 168 Series Manual de usuario

Fisher

Fisher POLY-CASTER 78601 Manual de usuario

TurfEx

TurfEx RS7200 Manual del propietario

Ferris

Ferris Pathfinder Series Manual de usuario

Fayat Group

Fayat Group DYNAPAC S100 Guía de solución de problemas

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Manual de instalación y operación

EASTMAN

EASTMAN CR 500 Manual de usuario

Nogueira

Nogueira RoyalFlow-600 Manual de usuario

Buyers

Buyers TGS05B Manual de usuario

Magnum

Magnum V-BOX PV Series Suplemento

Meyer's

Meyer's VB280 Manual de usuario

Kramer

Kramer VM-400HDCP Manual de usuario

H&S

H&S 5134 Manual de usuario