SnowEx SP-9500X Manual de usuario
1
© Trynex International 2012 (REV A) F50734
FOR MODEL:
SP-9500X Serial # M2-100000 and higher
Madison Heights, Michigan 48071
800-725-8377
www.snowexproducts.com
Customer Copy
This Manual Must Be Read Before Operating The Equipment
Owner / Operator’s Manual
© Trynex International 2012 (REV A) F50734
2
General Information ...................................................................................................................................................................................... 3
Introduction ................................................................................................................................................................................................. 4
Safety .......................................................................................................................................................................................................... 5
Warning Decal Positions..............................................................................................................................................................................6-7
Operating the Spreader.............................................................................................................................................................................8-11
Spreader Maintenance ............................................................................................................................................................................... 12
Wiring Instructions ..................................................................................................................................................................................... 13
Control and Harness Diagram ............................................................................................................................................................... 14-19
Mounting Instructions ............................................................................................................................................................................ 20-21
Troubleshooting .................................................................................................................................................................................... 22-23
Warranty .................................................................................................................................................................................................... 24
Spreader Views
Model # SP-9500X....................................................................................................................................................................... 25
Frame Assembly Parts Breakdown
Model # SP-9500X.................................................................................................................................................................. 26-27
Auger Drive Assembly Parts Breakdown
Model # SP-9500X.................................................................................................................................................................. 28-29
Hopper Assembly Parts Breakdown
Model # SP-9500X.................................................................................................................................................................. 30-31
Auger Extension Assembly Parts Breakdown
Model # SP-9500X.................................................................................................................................................................. 32-33
Drive Assembly Parts Breakdown
Model # SP-9500X.................................................................................................................................................................. 34-35
Notes .............................................................................................................................................................................................. 36-37
Table of Contents
Have a question or need assistance?
SnowEx Customer Care
(800) 725-8377
or (248) 586-3500
Monday through Friday 8:00 AM to 4:30 PM EST
Fax: (248) 691-8378
E-Mail: customercare@trynexfactory.com
Website: www.snowexproducts.com
3
© Trynex International 2012 (REV A) F50734
CONGRATULATIONS!
The spreader you have purchased is an example of snow and ice control technology at its nest! Your spreader’s self-contained design is a
trademark of all SnowEx products. Here’s why…
SIMPLICITY: Fewer moving parts manufactured of higher quality means minimal maintenance for your SnowEx spreader.
RELIABILITY: High impact linear low density polyethelyne hopper. State-of-the-art electronic dual variable speed control, custom engineered
powder coated frame, maximum torque 12-volt motor coupled to a custom engineered transmission; found only on SnowEx products.
VERSATILITY: Multi-use capabilities allows spreading of a variety of materials for snow and ice control.
WARRANTY: Best in the industry, hands down! 2 years standard and now 5 year extended (optional).
The benets you are about to recognize are that of time, money and effort.
We welcome you to the world of SnowEx Performance.
Registration
Record the following information in this manual for quick reference.
Spreader Model Number
Spreader Serial Number
Handheld Control Pendant Serial Number Control Board Serial Number
Date of Purchase
Dealer Where Purchased
When ordering Parts, the above information is necessary. This will help to see that you
receive the correct parts.
At the right is a diagram of the ID tag. This tag on the spreader is located on the
frame.
Please ll out the warranty card with all the necessary information to validate it.
This will also give us a record so that any safety or service information can be
communicated to you.
General Information
SP-9500X
M2-100000
© Trynex International 2012 (REV A) F50734
4
Introduction
This manual has been designed for your help. It will assist you and instruct you on the proper set-up, installation and use of this spreader.
Refer to the table of contents for an outline of this manual.
We require that you read and understand the contents of this manual completely (especially all safety information) before attempting any
procedure contained herein.
THIS SIGN SHOULD ALERT YOU:
The Society of Automotive Engineers has adopted this SAFETY ALERT SYMBOL to pinpoint characteristics
that, if NOT carefully followed, can create a safety hazard. When you see this symbol in this manual or on the
machine itself, BE ALERT! Your personal safety and the safety of others is involved.
Dened below are the SAFETY ALERT messages and how they will appear in this manual:
(RED)
Information that, if not carefully followed,
can cause death!
(ORANGE)
Information that, if not carefully followed,
can cause serious personal injury or death!
(YELLOW)
Information that, if not carefully followed,
can cause minor injury or damage to equipment
5
© Trynex International 2012 (REV A) F50734
Safety
Before attempting any procedure in this book, these safety instructions must be read and understood by all workers who have any part in the
preparation or use of this equipment.
For your safety warning and information decals have been placed on this product to remind the operator of safety precautions . If anything
happens to mark or destroy the decals, please request new ones from SnowEx.
Never exceed the Gross Vehicle Weight Rating of vehicle. Failure to do so may limit a vehicles handling
characteristics.
Never attempt to take a unit off a truck with material in it.
Always keep hands, feet, and clothing away from power driven parts.
Unit must be pinned and locked into position before operating vehicle.
Always shut off vehicle and power source before attempting to attach or detach or service unit Be sure
vehicle/power source is properly braked or chocked.
Remember, most accidents are preventable and caused by human error. Exercising of care and precautions
must be observed to prevent the possibility of injury to operator or others!
Never operate equipment when under the inuence of alcohol, drugs, or medications that might alter your
judgment and/or reaction time.
Before working with the spreader, secure all loose tting clothing and unrestrained hair.
Always wear safety glasses with side shields when servicing spreader. Failure to do this could result in
serious injury to the eyes.
Never allow children to operate or climb on equipment.
Always check areas to be spread to be sure no hazardous conditions or substances are in the area.
Always inspect unit for defects: broken, worn or bent parts, weakened areas on spreader.
Remember it is the owner’s responsibility to communicate information on safe usage and proper
maintenance of all equipment.
Always make sure personnel are clear of areas of danger when using equipment.
Never weld or grind on equipment without having a re extinguisher available.
Inspect the unit periodically for defects. Parts that are broken, missing or worn out must be replaced
immediately. The unit or any part of it can not be altered without prior written permission from the
manufacturer.
Always inspect pins and latches whenever attaching or detaching spreader, and before operation of spreader.
Never exceed 45 m.p.h. when loaded spreader is attached to vehicle. Braking distances may be increased
and handling characteristics may be impaired at speeds above 45 m.p.h.
Never use wet materials or materials with foreign debris with any of these spreaders. These units are
designed to handle dry, clean, free owing material.
Never leave material in hopper for long periods of time. Be aware that all ice melters are hygroscopic and will
attract atmospheric moisture and harden up.
© Trynex International 2012 (REV A) F50734
6
Warning Decal Positions
Model # SP-9500X
• Read Owner’s Manual for Installation Instructions.
• Secure spreader to truck with ratchet straps.
• Anchor spreader securely to truck body with bolt kit provided to prevent
slipping or sliding.
• Routinely check straps and handware to make sure they are secure.
7.25in w x 3.00in h
D6548_Warning.ai
D6548
D6192_Warning.ai4in x 2.25in
ROTATING AUGER CAN CAUSE
SERIOUS INJURY OR DEATH
• Keep arms, hands, and loose clothing
away from auger.
• Shut off control and unplug spreader
before servicing.
D6335
7.25in w x 3.00in h
D6335_Warning.ai
• DO NOT REMOVE SPREADER WITH MATERIAL IN HOPPER
• FASTEN SPREADER DOWN WITH APPROVED RATCHET STRAPS
AND BOLT KIT
• REAR FRAME LOCATOR BARS MUST BE IN PLACE BEFORE
OPERATING VEHICLE
DANGER
7.25in w x 3.00in h
D6547_Warning.ai
D6547
7
© Trynex International 2012 (REV A) F50734
Warning Decal Positions
Model # SP-9500X
ROTATING AUGER CAN CAUSE
SERIOUS INJURY OR DEATH
• Keep arms, hands, and loose clothing
away from auger.
• Shut off control and unplug spreader
before servicing.
D6335
7.25in w x 3.00in h
D6335_Warning.ai
• DO NOT EXCEED GVWR OF VEHICLE
• DO NOT OVERLOAD SPREADER
• LOAD SPREADER EVENLY
7.25in w x 3.00in h
D6546_Warning.ai
D6546
D6194_Warning.ai4in x 2.25in
• DO NOT REMOVE SPREADER WITH MATERIAL IN HOPPER
• FASTEN SPREADER DOWN WITH APPROVED RATCHET STRAPS
AND BOLT KIT
• REAR FRAME LOCATOR BARS MUST BE IN PLACE BEFORE
OPERATING VEHICLE
DANGER
7.25in w x 3.00in h
D6547_Warning.ai
D6547
ROTATING PARTS CAN CAUSE
SERIOUS INJURY OR DEATH
• ALWAYS DISCONNECT POWER
WHEN NOT IN USE
ROTATING PARTS CAN CAUSE
SERIOUS INJURY OR DEATH
• ALWAYS DISCONNECT POWER
WHEN NOT IN USE
4.25in w x 3.25in h
X00000_Spinner_Warning.ai
© Trynex International 2012 (REV A) F50734
8
Operating the Spreader
Model # SP-9500X
SPREADER LOADING
WARNING – Do not overload vehicle. Use chart below to calculate weight of material. Weights of material are an average for dry
materials.
Material Weight Per Cubic Ft.
Rock Salt 80-90 lbs.
Sand/Salt Mix 95-120 lbs.
• Warning – Never leave material in hopper for long periods of time as salt is hygroscopic and will attract atmospheric moisture and harden up.
When spreading sand mix, a 1:1 ratio for Sand/Salt mix is recommended to prevent the material from freezing.
SPREADER OPERATION
• The Dual Variable Speed Controller has dual nger-tip dials for maximum performance, digital system status with warning protection and built-
in Vibrator Switch.
• To start, press power switch on controller and spreader will accelerate to speed set on spinner and auger dials.
• To stop, press power on controller to off position.
• Speed of Auger and Spinner may be adjusted separately to get desired ow and spread distance
• The Vibrator Switch is needed for dense material or to increase the ow to the Auger. This eliminates bridging of material in hopper.
• It is important that the Inverted Vee not be removed except when servicing.
• If there are any problems while operating the spreader, refer to Troubleshooting Guide.
SPREADING TIPS
• Spread ice melters with the storm to prevent unmanageable levels of ice.
• Never exceed 10 m.p.h. when spreading.
• For a wider pass, increase spinner speed.
• For a heavier pass, drive slower or increase auger speed.
• Never operate spreader near pedestrians.
• Calculate spread pattern when near vegetation.
9
© Trynex International 2012 (REV A) F50734
WARNING PROTECTION
• If audible beeping occurs, read display to identify problem. If display reads “OL” (overload) or “OH” (overheat), shut the controller down and
carefully clear jammed auger. If display reads “E1” this means there is a dead short in the system. Do not use until problem is corrected. If
the display reads “E0” this means the motor is not getting any power. Check all connections. If the display reads “LB” the vehicle battery is
extrememly low (possibly caused by a poor or corroded connection) and could damage the system.
• If there are any problems while operating the spreader, refer to Troubleshooting Guide.
AUTO-REVERSE “AR” FUNCTION
• If your controller displays “OL” this could indicate a jammed auger.
• To engage the Auto-Reverse “AR” Function:
Step 1: Shut the Main Power Switch OFF for 3 seconds.
Step 2: Turn the Main Power Switch ON. When the machine starts back up, the “AR” sequence will automatically start and the auger will
reverse for several rotations to clear the jam.
• After a pause of several moments, the auger will automatically return to correct rotation. If the jam is still not cleared, the controller will again
display “OL.”
• You may repeat Steps 1 and 2 for a second and third time.
• If after the third try the controller displays “OL,” you must extract the material that is causing the problem.
• Follow all warning directions when clearing jams.
Operating the Spreader (continued)
Model # SP-9500X
© Trynex International 2012 (REV A) F50734
10
Operating the Spreader (continued)
Model # SP-9500X
ADJUSTABLE SPINNER INSTRUCTIONS
Your spreader is equipped with an adjustable spinner to assist you in more precise material application. The Spinner plate gives the operator
control of whether the material spreads to the right, left or is centered. All of the ns should be in the same position; this will keep the spread
pattern consistent and have even ground coverage. Before operating the spreader, spread some material in a clear area where you can easily
observe the spread pattern and how it changes. Adjust according to the instructions below to get the pattern you desire.
When looking down at the spinner, moving the ns clockwise will
adjust the spread pattern toward the left side of the spreader.
When looking down at the spinner, moving the ns counter-clockwise
will adjust the spread pattern toward the right side of the spreader.
When the ns are in their center adjustment position, the spread pat-
tern will be mostly centered. However, collisions and other damage to
the equipment may change this. Check the n position and resulting
spread pattern often enough to prevent the equipment performance
from being adversely affected.
Tabla de contenidos
Otros manuales de Esparcidor de SnowEx
SnowEx
SnowEx Drop Pro 600 Manual de usuario
SnowEx
SnowEx SP-325 Instrucciones de funcionamiento
SnowEx
SnowEx HELIXX Manual de usuario
SnowEx
SnowEx VX-6010 Manual de usuario
SnowEx
SnowEx SP-85 Instrucciones de funcionamiento
SnowEx
SnowEx V-Maxx G2 VX-6010 Manual de usuario
SnowEx
SnowEx Precision Pro SP-1675 Manual de usuario
SnowEx
SnowEx V-Maxx G2 Manual de usuario
SnowEx
SnowEx Bulk-Pro 1875 Manual de usuario
SnowEx
SnowEx VX-4210 Manual de usuario
SnowEx
SnowEx 7500 Manual de usuario
SnowEx
SnowEx SP-8550 Manual del propietario
SnowEx
SnowEx SP-2400 Manual del propietario
SnowEx
SnowEx Super Maxx SP-9300XH Instrucciones de funcionamiento
SnowEx
SnowEx SP-85 Instrucciones de funcionamiento
SnowEx
SnowEx SP-85 Manual del propietario
SnowEx
SnowEx K1-131116 Manual del propietario
SnowEx
SnowEx SP-65 Manual del propietario
SnowEx
SnowEx SP-9300 Manual de usuario
SnowEx
SnowEx Bulk Pro SP-1575 Instrucciones de funcionamiento
Manuales populares de Esparcidor de otras marcas
Fisher
Fisher POLY-CASTER 78601 Manual de usuario
TurfEx
TurfEx RS7200 Manual del propietario
Ferris
Ferris Pathfinder Series Manual de usuario
Fayat Group
Fayat Group DYNAPAC S100 Guía de solución de problemas
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Manual de instalación y operación
EASTMAN
EASTMAN CR 500 Manual de usuario
