Snom M3 Manual
SNOM
m3
PhoneSetup
User Guide
Version1.0
Updated
5/7/2008
Page 2of 5
Overview
This guide provides an overview of setting up the Snow m3 telephone.
General Support
If you have questions or need technical assistance with Evolution PBX call (888)
If you have questions about third party hardware or software please visit the following
Websites:
•Snom VoIP Wireless Telephone: http://www.snom.com
•Snap: http://www.snapanumber.com.
•iView: http://www.i9technologies.com/.
•Cisco VoIP Telephones: http://www.cisco.com.
•CounterPath Software Telephones - http://www.counterpath.com.
•Digium PCI Cards: http://www.digium.com.
•Linksys Analog Terminal Adapters and VoIP telephones: http://www.linksys.com.
•Polycom VoIP Telephones: http://www.polycom.com.
My Evolution PBX Doesn’t Do That!
Some features and configuration options in this document may only be available with a
recent software upgrade available from Intuitive Voice Technology. Email
the feature that you are interested in).
Errata
Please report errors or confusing descriptions by sending an Email to
Page 3of 5
SettingUptheSnomm3Telephone
The snom m3 is a far reaching and expandable cordless add-on to your Evolution PBX
with an indoor range of 150 feet and an outdoor range of 300 feet or more.
ConfiguringtheSnomm3inEvolutionPBX
To Configure a Basic Extension for the Snom m3 in Evolution PBX
1. Login to Evolution PBX, click the Resources tab then click Phone Extensions.
2. In the New Device field, select VoIP--GENERIC SIP and the Modify Phones
window displays.
3. In the Extension field, select an available extension.
4. In the Caller ID Name field, enter the name you want to be passed as this
extension’s caller ID text.
5. In the Caller ID Number field, enter the number you want to be passed as this
extension’s caller ID number.
6. In the Time Zone field, select the appropriate time zone for the time zone where
the phone will be located.
7. In the Remote Phone field, select Yes if the phone will not be on the same
subnet as the Evolution PBX server (for example, if the phone belongs to a user
that is located at a remote location). Select No if this is not the case.
Note: The other options on the Modify Phones frame are optional or advanced.
8. Click Save.
Note: The Evolution PBX Web configuration interface requires that your browser’s popup
blocker be turned off or disabled so that the Device Settings screen can be seen.
9. Write down the device settings for your new extension that are displayed on the
screen. These settings will be used to configure your phone.
Page 4of 5
ConfiguringtheSnomm3WirelessTelephone
To Configure the Snom m3 Wireless Telephone
1. Connect the Snom m3 base station to your Ethernet network.
2. Click the volume up button on the handset and the IP Address the Snom m3
acquired from your network is given.
3. Write down the IP Address, open a Web Browser then enter the IP Address (for
example, http://192.168.2.33) into the Address bar.
4. Enter your username and password then Press Enter to login and the Snom m3
configuration window displays.
5. Click Identity 1, to configure phone 1 of 8 possible phones and the Configuration
Identity 1 window displays.
6. In the Server is Local field, select Yes.
7. In the Display Name field, enter your caller ID name.
8. In the Account field enter the generic extension configured earlier in Evolution PBX.
9. In the Password field, enter the password provided by Evolution PBX you wrote
down when you created your default extension.
Page 5of 5
10.In the Account Name field, enter a name for your account.
11.In the Account Mailbox Name field, enter the generic extension configured
earlier in Evolution PBX.
12.In the Account Mailbox Number field, enter the generic extension configured
earlier in Evolution PBX.
13.In the Registrar field, enter the IP Address (for example, 192.168.2.225) of
your Evolution PBX server.
14.In the Outbound Proxy field, enter the IP Address (for example,
192.168.2.225) of your Evolution PBX server.
15.In the Authentication Username field, enter the generic extension configured
earlier in Evolution PBX.
16.In the Server Port field, enter 5060.
17.In the Re-registration time field, enter 600.
18.In the Registrar Config field, select Add domain.
19.In the DTMF Signaling field, select RFC 2833.
20.In the Codec Priority field, prioritize accordingly: PCMU, PCMA, iLBC (20ms) then
G729AB.
21.In the Enable Silence Suppression field, select No.
22.Click Save Settings and the telephone will save, reboot, and automatically
register with Evolution PBX.
Note: All other settings are optional.
Otros manuales para M3
4
Tabla de contenidos
Otros manuales de Teléfono IP de Snom
Snom
Snom 710 Manual de usuario
Snom
Snom M25 Manual de usuario
Snom
Snom 370 Guía de inicio rápido
Snom
Snom M9 Manual de instrucciones
Snom
Snom 300 Manual de usuario
Snom
Snom 320 Manual de usuario
Snom
Snom 320 Manual de usuario
Snom
Snom uc600 Manual de usuario
Snom
Snom 00004258 Manual de usuario
Snom
Snom 370 Instrucciones de funcionamiento originales
Snom
Snom D335 Manual de usuario
Snom
Snom 100 v1.9a Manual de usuario
Snom
Snom 715 Manual de usuario
Snom
Snom 715 Manual de usuario
Snom
Snom 300 Manual de usuario
Snom
Snom 7 Series Manual de usuario
Snom
Snom M9 Manual de servicio
Snom
Snom D865 Hoja de información del producto
Snom
Snom 360 Manual de usuario
Snom
Snom 320 Manual de usuario
