SMC Networks BR21VPN - annexe 1 Manual de usuario

Barricade™

Dual WAN Port Load Balancing VPN Router

SMCBR21VPN

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate

and reliable. However, no responsibility is assumed by SMC for its use, nor for

any infringements of patents or other rights of third parties which may result from

its use. No license is granted by implication or otherwise under any patent or

patent rights of SMC. SMC reserves the right to change specifications at any

time without notice.

SMC Networks, Inc.

20 Mason

Irvine, CA 92618

Trademarks:

SMC is a registered trademark; and EZ Connect is a trademark of SMC Networks,

Inc. Other product and company names are trademarks or registered trademarks of

their respective holders.

LIMITED WARRANTY

Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free

from defects in workmanship and materials, under normal use and service, for the

applicable warranty term. All SMC products carry a standard 90-day limited warranty from

the date of purchase from SMC or itsAuthorized Reseller. SMC may, at its own discretion,

repair or replace any product not operating as warranted with a similar or functionally

equivalent product, during the applicable warranty term. SMC will endeavor to repair or

replace any product returned under warranty within 30 days of receipt of the product. The

standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering

new products within 30 days of purchase from SMC or its Authorized Reseller. Registration

can be accomplished via the enclosed product registration card or online via the SMC

website. Failure to register will not affect the standard limited warranty. The Limited

Lifetime warranty covers a product during the Life of that Product, which is defined as the

period of time during which the product is an “Active” SMC product. A product is

considered to be “Active” while it is listed on the current SMC price list. As new

technologies emerge, older technologies become obsolete and SMC will, at its discretion,

replace an older product in its product line with one that incorporates these newer

technologies. At that point, the obsolete product is discontinued and is no longer an

“Active” SMC product. A list of discontinued products with their respective dates of

discontinuance can be found at:

http://www.smc.com/index.cfm?action=customer_service_warranty.

All products that are replaced become the property of SMC. Replacement products may

be either new or reconditioned. Any replaced or repaired product carries either a 30-day

limited warranty or the remainder of the initial warranty, whichever is longer. SMC is not

responsible for any custom software or firmware, configuration information, or memory

data of Customer contained in, stored on, or integrated with any products returned to SMC

pursuant to any warranty. Products returned to SMC should have any customer-installed

accessory or add-on components, such as expansion modules, removed prior to returning

the product for replacement. SMC is not responsible for these items if they are returned

with the product. Customers must contact SMC for a Return Material Authorization number

prior to returning any product to SMC. Proof of purchase may be required. Any product

returned to SMC without a valid Return Material Authorization (RMA) number clearly

marked on the outside of the package will be returned to customer at customer’s expense.

For warranty claims within North America, please call our toll-free customer support

number at (800) 762-4968. Customers are responsible for all shipping charges from their

facility to SMC. SMC is responsible for return shipping charges from SMC to customer.

WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATEAS

WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR

REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE

FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF

ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN

FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING

WARRANTIES OR CONDITIONS OF MERCHANTABILITYAND FITNESS FORA

PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER

PERSON TO ASSUME FOR ITANY OTHER LIABILITY IN CONNECTION WITH THE

SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL

NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION

DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS

CAUSED BY

CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER

INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY

OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BYACCIDENT,

FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASEDIN CONTRACT OR TORT

(INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR

FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS

ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,

MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS

PRODUCTS, EVEN IF SMC OR ITSAUTHORIZED RESELLER HAS BEENADVISED

OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOTALLOW THE

EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE

LIMITATIONS AND EXCLUSIONS MAY NOTAPPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL

RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY

SHALL BE TAKEN TOAFFECT YOUR STATUTORY RIGHTS.

* SMC will provide warranty service for one year following discontinuance from the active

SMC price list. Under the limited lifetime warranty, internal and external power supplies,

fans, and cables are covered by a standard one-year warranty from date of purchase.

SMC Networks, Inc.

20 Mason

Irvine, CA 92618

COMPLIANCES

FCC - Class A

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with instructions, may cause harmful interference to radio

communications. However, there is no guarantee that the interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient the receiving antenna

•Increase the separation between the equipment and receiver

•Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

•Consult the dealer or an experienced radio/TV technician for help

EC Conformance Declaration - Class A

SMC contact for these products in Europe is:

SMC Networks Europe,

Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a,

08970 - Sant Joan Despí,

Barcelona, Spain.

This information technology equipment complies with the requirements of the Council

Directive 89/336/EEC on the Approximation of the laws of the Member States relating to

Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within

certain

voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the

compliance with these Directives, the following standards were applied:

RFI Emission:

•Limit class A according to EN 55022:1998, IEC 60601-1-2 (EMC,medical)

•Limit class A for harmonic current emission according toEN 61000-3-2/1995

•Limitation of voltage fluctuation and flicker in low-voltage supply system

according to EN 61000-3-3/1995

Immunity:

•Product family standard according to EN 55024:1998

•Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

•Radio-frequency electromagnetic field according to EN 61000-4-3:1996

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

•Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC

power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

•Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

•Immunity to conducted disturbances, Induced by radio-frequency fields:

EN 61000-4-6:1996 (0.15 - 80 MHz with

1 kHz AM 80% Modulation: 3 V/m)

•Power frequency magnetic field immunity test according to

EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)

•Voltage dips, short interruptions and voltage variations immunity test

according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%

Reduction @500 ms, >95% Reduction @5000 ms)

LVD:

•EN 60950-1:2001

Please read the following safety information carefully

before installing the device:

WARNING: Installation and removal of the unit must be carried out by

qualified personnel only.

•This guide is intended for use by network administrators who are

responsible for setting up and installing network equipment;

consequently it assumes a basic working knowledge of LANs (Local Area

Networks).

•The unit must be connected to an earthed (grounded) outlet to comply with

international safety standards.

•Do not connect the unit to an A.C. outlet (power supply) without an

earth (ground) connection.

•The appliance coupler (the connector to the unit and not the wall plug)

must have a configuration for mating with an EN 60320/IEC 320

appliance inlet.

•The socket outlet must be near to the unit and easily accessible. You can only

remove power from the unit by disconnecting the power cord from the outlet.

•This unit operates under SELV (Safety Extra Low Voltage) conditions

according to IEC 60950. The conditions are only maintained if the

equipment to which it is connected also operates under SELV

conditions.

Veuillez lire à fond l’information de la sécurité suivante avant d’installer le Device:

AVERTISSEMENT: L.installation et la dépose de ce groupe doivent être

confiés à un personnel qualifié.

•Ne branchez pas votre appareil sur une prise secteur (alimentation

électrique) lorsqu’il n’y a pas de connexion de mise à la terre (mise à la

masse).

•Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse)

afin de respecter les normes internationales de sécurité.

•Le coupleur d.appareil (le connecteur du groupe et non pas la prise

murale) doit respecter une configuration qui permet un branchement sur une

entrée d.appareil EN 60320/IEC 320.

•La prise secteur doit se trouver à proximité de l.appareil et son accès doit être

facile. Vous ne pouvez mettre l.appareil hors circuit qu.en

débranchant son cordon électrique au niveau de cette prise.

•L.appareil fonctionne à une tension extrêmement basse de sécurité qui

est conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si

l.équipement auquel il est raccordé fonctionne dans les mêmes conditions.

Bitte unbedingt vor dem Einbauen des RPU die

folgenden Sicherheitsanweisungen durchlesen:

WARNUNG: Die Installation und derAusbau des Geräts darf nur durch

Fachpersonal erfolgen.

•Diese Anleitung ist fr die Benutzung durch Netzwerkadministratoren

vorgesehen, die fr die Installation und das einstellen von

Netzwerkkomponenten verantwortlich sind; sie setzt Erfahrung bei derArbeit mit

LANs (Local Area Networks) voraus.

•Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose

angeschlossen werden.

•Das Gerät muß an eine geerdete Steckdose angeschlossen werden,

welche die internationalen Sicherheitsnormen erfüllt.

•Der Gerätestecker (der Anschluß an das Gerät, nicht der

Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320

konfigurierten Geräteeingang haben.

•Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich

sein. Die Stromversorgung des Geräts kann nur durch Herausziehen des

Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.

•Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen

(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind

nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter

SELV-Bedingungen betrieben werden

Stromkabel. Dies muss von dem Land, in dem es

benutzt wird geprüft werden:

Schweiz Dieser Stromstecker muß die SEV/ASE

1011Bestimmungen ein- halten.

Europe Das Netzkabel muß vom Typ

HO3VVF3GO.75 (Mindestan-

forderung) sein und die Aufschrift <HAR>

oder <BASEC> tragen

Der Netzstecker muß die Norm CEE 7/7

erfüllen (.SCHUKO.).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de SMC Networks

SMC Networks

SMC Networks Barricade SMC7401BRA Manual de usuario

SMC Networks

SMC Networks Barricade SMC7204BRA Manual de usuario

SMC Networks

SMC Networks BARRICADE SMC7301TA Manual de usuario

SMC Networks

SMC Networks TigerCard 1000 Manual de usuario

SMC Networks

SMC Networks EZ Connect SMC2870W Manual de usuario

SMC Networks

SMC Networks TigerAccess SMC7824M/VSW Guía de instalación

SMC Networks

SMC Networks SMC6752AL2 Manual de usuario

SMC Networks

SMC Networks Wireless Broadband Router Manual de usuario

SMC Networks

SMC Networks SMC6724AL2 Manual de usuario

SMC Networks

SMC Networks 7904BRB3 FICHE Instrucciones de funcionamiento y seguridad

SMC Networks

SMC Networks Barricade Plus SMC7004FW Manual de usuario

SMC Networks

SMC Networks Barricade SMC7004ABR Manual de usuario

SMC Networks

SMC Networks Barricade SMC7401BRA Manual de usuario

SMC Networks

SMC Networks SMC Barricade Plus SMC7004WFW Manual de usuario

SMC Networks

SMC Networks SMC-EZ1026DT Manual de usuario

SMC Networks

SMC Networks FS26 Manual de usuario

SMC Networks

SMC Networks GS1601 Manual de usuario

SMC Networks

SMC Networks GS501 Manual de usuario

SMC Networks

SMC Networks SMCFS1601 - FICHE TECHNIQUE Manual de usuario

SMC Networks

SMC Networks 7004VBR Manual de usuario

SMC Networks

SMC Networks SMC6826MPE Manual de usuario

SMC Networks

SMC Networks Barricade SMC7401BRA Manual de usuario

SMC Networks

SMC Networks 7004VBR Manual de usuario

SMC Networks

SMC Networks SMCGS502 - FICHE TECHNIQUE Instrucciones de funcionamiento y seguridad

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad