SMC Networks Barricade SMC7401BRA Manual de usuario

2-Port Broadband Router

with Built-in ADSL Modem

◆ Compatible with all leading DSLAMs

◆ Supports DMT line modulation

◆ Supports full-rate ADSL (G.992.1 & T1.413, Issue 2)

- Up to 8 Mbps downstream and 640 Kbps upstream

◆ Supports G.lite ADSL (G.992.2)

- Up to 1.5 Mbps downstream and 512 Kbps upstream

◆ Supports DSL handshaking (G.994.1)

◆ Multiple user Internet access with a single user account

◆ Plug & Play installation

◆ Web-based management

User Guide

SMC7401BRA

ADSL Router

User Guide

From SMC’s Barricade line of

award-winning connectivity solutions

May 2002

PartNo: EU 750.7582, UK 750.7595

Pub No: 150000013600E R02

SMC's Limited Warranty Statement

Limited Warranty Statement: SMC Networks Europe ("SMC") warrants its

products to be free from defects in workmanship and materials, under

normal use and service, for the applicable warranty term. All SMC products

carry a standard 2 year limited warranty from the date of purchase from SMC

or its Authorised Reseller. SMC may, at its own discretion, repair or replace

any product not operating as warranted with a similar or functionally

equivalent product, during the applicable warranty term. SMC will endeavour

to repair or replace any product returned under warranty within 30 days of

receipt of the product. As new technologies emerge, older technologies

become obsolete and SMC will, at its discretion, replace an older product in

its product line with one that incorporates these newer technologies

The standard limited warranty can be upgraded to a 5 year Limited

Lifetime * warranty by registering new products within 30 days of

purchase from SMC or its Authorised Reseller. Registration can be

accomplished via the enclosed product registration card or online via the

SMC web site. Failure to register will not affect the standard limited

warranty. The Limited Lifetime warranty covers a product during the Life

of that Product, which is defined as a period of 5 years from the date of

purchase of the product from SMC or its authorised reseller.

All products that are replaced become the property of SMC. Replacement

products may be either new or reconditioned. Any replaced or repaired

product carries, either a 30-day limited warranty or the remainder of the

initial warranty, whichever is longer. SMC is not responsible for any

custom software or firmware, configuration information, or memory data

of Customer contained in, stored on, or integrated with any products

returned to SMC pursuant to any warranty. Products returned to SMC

should have any customer-installed accessory or add-on components, such

as expansion modules, removed prior to returning the product for

replacement. SMC is not responsible for these items if they are returned

with the product.

Customers must contact SMC for a Return Material Authorisation number

prior to returning any product to SMC. Proof of purchase may be

required. Any product returned to SMC without a valid Return Material

Authorisation (RMA) number clearly marked on the outside of the

package will be returned to customer at customer’s expense. Customers

are responsible for all shipping charges from their facility to SMC. SMC is

responsible for return shipping charges from SMC to customer.

LIMITED WARRANTY

WARRANTIES EXCLUSIVE: IF A SMC PRODUCT DOES NOT OPERATE

AS WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY SHALL BE REPAIR

OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S

OPTION. THE FOREGOING WARRANTIES AND REMEDIES ARE

EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR

CONDITIONS, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY

OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING

WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR

AUTHORISES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER

LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION,

MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE

UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION

DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST

OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE,

NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORISED

ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE

OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR

OTHER HAZARD.

LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN

CONTRACT OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE

LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR

PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS

OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN

CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE,

PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN

IF SMC OR ITS AUTHORISED RESELLER HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

SOME COUNTRIES DO NOT ALLOW THE EXCLUSION OF IMPLIED

WARRANTIES OR THE LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE

ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY

VARY FROM COUNTRY TO COUNTRY. NOTHING IN THIS WARRANTY

SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.

* Under the limited lifetime warranty, internal and external power

supplies, fans, and cables are covered by a standard one-year warranty

from date of purchase.

LIMITED WARRANTY

Information furnished is believed to be accurate and reliable. However, no responsibility is assumed by our

company for its use, nor for any infringements of patents or other rights of third parties which may result

from its use. No license is granted by implication or otherwise under any patent or patent rights of our

company. We reserve the right to change specifications at any time without notice.

Trademarks:

Product and company names are trademarks or registered trademarks of their respective holders.

iii

OMPLIANCES

FCC - Class B

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that the interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Note:

In order to maintain compliance with the limits for a Class B digital device, you are

required to use a quality interface cable when connecting to this device. Changes or

modifications not expressly approved by our company could void the user’s

authority to operate this equipment.

Attach unshielded twisted-pair (UTP) to the RJ-45 port and shielded USB cable to

the USB port.

FCC - Part 68

This equipment complies with Part 68 of the FCC rules. This equipment comes with a label

attached to it that contains, among other information, the FCC registration number and

ringer equivalence number (REN) for this equipment. If requested, this information must be

provided to the telephone company.

This equipment uses the following USOC jacks: RJ11C

The REN is used to determine the quantity of devices that may be connected to the

telephone line. Excessive RENs on the telephone line may result in the devices not ringing in

response to an incoming call. In most, but not all areas, the sum of the RENs should not

exceed five (5.0). To be certain of the number of devices that may be connected to the line, as

determined by the total RENs, contact the telephone company to determine the maximum

REN for the calling area.

If this equipment causes harm to the telephone network, the telephone company will notify

you in advance that temporary discontinuance of service may be required. If advance notice is

not practical, the telephone company will notify the customer as soon as possible. Also, you

will be advised of your right to file a complaint with the FCC if you believe it is necessary.

OMPLIANCES

The telephone company may make changes in its facilities, equipment, operations, or

procedures that will provide advance notice in order for you to make the necessary

modifications in order to maintain uninterrupted service.

If trouble is experienced with this equipment, please contact our company at the numbers

shown on back of this manual for repair and warranty information. If the trouble is causing

harm to the telephone network, the telephone company may request you to remove the

equipment from the network until the problem is resolved.

No repairs may be done by the customer.

This equipment cannot be used on telephone company-provided coin service. Connection to

Party Line Service is subject to state tariffs.

When programming and/or making test calls to emergency numbers:

• Remain on the line and briefly explain to the dispatcher the reason for the call.

• Perform such activities in off-peak hours such as early morning or late evenings.

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a

computer or other electronic device to send any message via a telephone facsimile machine

unless such message clearly contains, in a margin at the top or bottom of each transmitted

page or on the first page of the transmission the date and time it is sent and an identification

of the business, other entity, or individual sending the message and the telephone number of

the sending machine or such business, other entity, or individual.

In order to program this information into your facsimile, refer to your communications

software user manual.

Industry Canada - Class B

This digital apparatus does not exceed the Class B limits for radio noise emissions from

digital apparatus as set out in the interference-causing equipment standard entitled “Digital

Apparatus,” ICES-003 of Industry Canada.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils

numériques de Classe B prescrites dans la norme sur le matérial brouilleur: “Appareils

Numériques,” NMB-003 édictée par l’Industrie.

OMPLIANCES

EC Conformance Declaration - Class B

This information technology equipment complies with the requirements of the Council

Directive 89/336/EEC on the Approximation of the laws of the Member States relating to

Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain

voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the

compliance with these Directives, the following standards were applied:

RFI Emission:

• Limit class B according to EN 55022:1998

• Limit class B for harmonic current emission according to

EN 61000-3-2/1995

• Limitation of voltage fluctuation and flicker in low-voltage supply

system according to EN 61000-3-3/1995

Immunity:

• Product family standard according to EN 55024:1998

• Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to EN 61000-4-3:1996

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/

DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by radio-frequency

fields: EN 61000-4-6:1996 (0.15 - 80 MHz with

1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to

EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations immunity test

according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%

Reduction @500 ms, >95% Reduction @5000 ms)

LVD:

• EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)

Otros manuales para Barricade SMC7401BRA

Tabla de contenidos

Otros manuales de Enrutador de red de SMC Networks

SMC Networks

SMC Networks 7204BRB Manual de usuario

SMC Networks

SMC Networks WUSB32 Manual de usuario

SMC Networks

SMC Networks BARRICADE N SMCWBR14SN5V2 Manual de usuario

SMC Networks

SMC Networks Barricade Manual de usuario

SMC Networks

SMC Networks Barricade Plus SMC7004FW Manual de usuario

SMC Networks

SMC Networks EZ1026DT Manual de usuario

SMC Networks

SMC Networks FS26 Manual de usuario

SMC Networks

SMC Networks 7904WBRA-N FICHE Guía de instalación

SMC Networks

SMC Networks Barricade SMC7401BRA Manual de usuario

SMC Networks

SMC Networks GS1601 Manual de usuario

SMC Networks

SMC Networks EZ Connect SMC2870W Manual de usuario

SMC Networks

SMC Networks 7301TA Manual de usuario

SMC Networks

SMC Networks EZ Connect SMC7003ADSL Manual de usuario

SMC Networks

SMC Networks SMC8612T2 Manual de usuario

SMC Networks

SMC Networks 7204BRB Manual de usuario

SMC Networks

SMC Networks EZ6516TX - annexe 1 Manual de usuario

SMC Networks

SMC Networks SMC6405TX Manual de usuario

SMC Networks

SMC Networks ADSL2 Barricade N Pro SMC7904WBRA-N Manual de usuario

SMC Networks

SMC Networks FS1601 Manual de usuario

SMC Networks

SMC Networks 7904BRB3 FICHE Manual de usuario

SMC Networks

SMC Networks TigerAccess SMC7824M/VSW Guía de instalación

SMC Networks

SMC Networks Barricade SMCWBR14S-N Manual de usuario

SMC Networks

SMC Networks SMC Barricade Plus SMC7004WFW Manual de usuario

SMC Networks

SMC Networks GS501 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad