Smart Start TRANSMISSION REMOTE STARTER Manual de usuario

TWO -WA Y FM LED AUTOMATIC/ MANUAL

TRANSMISSIO N REMO TE STARTER

INDUSTRY CANADA USER NOTICE:

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired operation of the device.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (EIRP) is not more than that required for successful communication.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this

equipment. Such modifications could void the user's authority to operate the equipment

_____________

User Guide

WARNING

It is the responsibility of the vehicle operator to ensure their

vehicle is parked in a safe and responsible manner.

1. a) Manual transmission: When leaving the vehicle, it is the user’s

responsibility to ensure that the gearshift lever is in the NEUTRAL

position and the parking brake is engaged in order to avoid accidents

upon remote starting.

b) Automatic transmission: When leaving the vehicle, it is the

user’s responsibility to ensure that the gearshift lever is in “Park” in

order to avoid accidents upon remote starting.

(Note: Make sure that the automatic vehicle cannot start in "Drive".)

2. It is the user's responsibility to ensure that the remote starter is

disabled or put into valet mode before servicing.

Designed & engineered in Canada

P.2 User Guide

Table of Contents

Government regulations ......................................................................................................... 3

Introduction with SmartStart™ .................................................................................... 3

Using the Remote Control ...................................................................................................... 4

Vehicle Presets ........................................................................................................................ 5

Heater .................................................................................................................................. 5

Windshield Wipers & Radio & Headlights............................................................................ 5

Arming and disarming the starter kill (if installed) .............................................................. 6

Remote-Starting Your Vehicle................................................................................................ 7

Setting Your Vehicle into Ready Mode................................................................................ 7

Remote-starting ................................................................................................................... 7

Driving Off............................................................................................................................ 8

Remote Starter Features ......................................................................................................... 8

Remote Door Locks ............................................................................................................. 8

Remote Trunk Release........................................................................................................ 8

Idle Mode ............................................................................................................................. 8

Valet Mode........................................................................................................................... 9

Panic Mode........................................................................................................................ 10

Quick LockoutTM................................................................................................................. 10

Cold Weather Mode........................................................................................................... 10

Extended Run Time ........................................................................................................... 11

Disable/Enable LED flashing ............................................................................................. 11

Constant output ................................................................................................................. 11

Feature Confirmation Chart.................................................................................................. 12

Advanced Features: Installation-programmable Options ................................................. 12

Ignition-controlled Door Locks ........................................................................................... 12

Secure Lock....................................................................................................................... 12

Safe Start........................................................................................................................... 13

Engine Run Time ............................................................................................................... 13

Turbo Mode ....................................................................................................................... 13

“Home ValetTM” Mode ........................................................................................................ 14

AUX 1................................................................................................................................. 14

AUX 2................................................................................................................................. 14

Horn Timing Adjustment .................................................................................................... 14

Multi-car Operation ............................................................................................................ 15

OEM-Style Alarm ............................................................................................................... 15

Intrusion Codes via horn.................................................................................................... 15

Vehicle Status Request......................................................................................................... 16

Status Request When the Engine IS NOT Running .......................................................... 16

Status Request When the Engine is Running ................................................................... 17

Ready Mode Status Request............................................................................................. 17

Troubleshooting Poor Transmitting Range ........................................................................ 17

Diagnostics – Parking Light Flash Table ............................................................................ 18

User Guide P.3

Government regulations

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

xReorient or relocate the receiving antenna.

xIncrease the separation between the equipment and receiver.

xConnect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

xConsult the dealer or an experienced radio/TV technician for help.

This device complies with the Industry Canada Radio Standards Specification RSS 210. Its use is

authorized only on a no-interference, no-protection basis; in other words, this device must not be

used if it is determined that it causes harmful interferences to services authorized by IC. In

addition, the user of this device must accept any radio interface that may be received, even if this

interference could affect the operation of the device.

Warning! Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate this device.

Introduction with SmartStart™

This is a state-of-the-art remote car starter system. The system is packed with advanced features

such as priority access to the driver’s door (commodity features), the Safe Start children safety

feature and SmartStart™.

SmartStart™ is a groundbreaking technology that enables your remote starter features to be

accessed by your smartphone. Features include keyless entry, trunk release, panic, remote

start/stop toggle and alarm notifications1. Note: SmartStart™ must be professionally installed. For

more information, see your nearest authorised Directed Canada dealer.

With many advanced functions, this product will satisfy any one of your expectations from high-end

commodity and security systems, without neglecting any standard feature commonly offered by

entry-level starters.

1Certain conditions apply. See your authorised Directed Canada dealer.

P.18 User Guide

Diagnostics – Parking Light Flash Table

Parking lights flashes

Description

xDoors locked.

Trunk released.

Start signal received from the remote.

xRuntime has expired.

2 fast

xDoors unlocked.

xValet mode is deactivated.

2 slow

xShutdown by remote.

3 slow

xRuntime is extended.

1 slow ÆÆ2 fast

xValet mode activated.

4 fast

xShutdown by brake.

xA remote start was attempted while the brake pedal is engaged.

10 fast

xShutdown by hood.

xA remote start was attempted while the hood is open.

ON ÎÎtwice

xCold weather mode deactivated.

ON ÎÎ3 times

xCold weather mode activated.

Solid ON

xEngine is running under remote start.

Flash for 30 sec.

xPanic mode is triggered.

Flash for 60 sec.

xAlarm is triggered.

ON ÎÎtwice ÎÎtwice

xA remote start was attempted while the system is in home valet.

User Guide P.17

Status Request When the Engine is Running

When the vehicle doors are locked:

The LED # 1 will flash 3 times to denote that the vehicle’s doors are locked.

When the vehicle doors are unlocked:

The LED # 2 will flash 3 times to denote that the vehicle’s doors are unlocked.

And:

RUN TIME

Beep(s

LED #1

LED #2

LED #3

LED #4

If there is more than 3/4 of

Run time cycle

ON for

sec

ON for 1-

sec

ON for 1-

sec

ON for 1-

sec

If there is more than half of

run time cycle

ON for 1

sec

ON for 1-

sec

ON for 1-

sec

If there is more than 1/4 of

run time cycle

ON for 1

sec

ON for 1-

sec

If there is less than 1/4 of

run time cycle

ON for 1

sec

Ready Mode Status Request

STATUS

SEQUENCE

LED #1

LED #2

LED #3

LED #4

Beep(s)

In Ready

Mode

if locked

3 flashes

if unlocked

3 flashes

Out of

Ready Mode

1st sequence

if locked

3 flashes

1st sequence

if unlocked

3 flashes

2nd sequence

Troubleshooting Poor Transmitting Range

Many factors may affect the operating range of the transmitter. Some of these are:

xThe condition of the battery in the transmitter.

xThe operating environment (for example: downtown radio-frequency noise, airports, cellular

phone towers…).

xMetal: any type of metal will affect operating range. This includes the metal in the car.

xThe shape of the vehicle can affect range as well; vans in general have an especially poor

range.

xThe shape of the roof and A-pillars brings about considerable radio-frequency deflection (in

this case the signal from the remote control). As a result, the direction in which the vehicle is

facing in relation to the remote control can affect the range. Straight on – standing in front of

the vehicle – generally gives you the greatest range; the second best performance is from the

back. Using the remote control from either side of the vehicle will usually give the lowest

range.

xThe range will be significantly lower in a crowded parking lot than in open space.

xAlways hold the transmitter high, approximately at shoulder height. Holding the transmitter

against your chin will also increase your range: your head acts as an antenna.

xThe operating range will be somewhat lower on vehicles equipped with an aftermarket or

factory alarm.

P.4 User Guide

Using the Remote Control

Your remote starter is equipped with a 5-button multi-channel remote control. It can operate two

independent vehicles equipped with a remote starter (see Multi-car operation section on page-

15). The functions of the transmitter are as follows:

2-way LED remote

LOCK: Locks the doors and arms

the STARTER KILL (if installed).

UNLOCK: Unlocks the doors and

disarms the STARTER KILL (if

installed). Activates the AUX

output if Priority Door Access is

configured.

TRUNK: Opens the TRUNK or

activates the AUX 3 output.

Note:

Trunk option must be

installed.

LED #1

(lock)

LED #2

(unlock)

START/STOP: Remote starts or

stops the engine. Gets the system

into Cold Weather mode by

pressing the SHIFT

button and

then pressing and holding the

START/STOP

button for

3 seconds. Note: Icon may vary.

LED #3

(trunk)

LED #4

(start)

AUX

AUX (upper right side): This

button serves as a second function

button.

This button allows assigning

different functions to any of the

other four buttons.

User Guide P.5

1-way companion remote (where available)

LOCK: Locks the doors and arms the STARTER

KILL (if installed).

UNLOCK: Unlocks the doors and disarms the

STARTER KILL (if installed). Activates the AUX

output if Priority Door Access is configured.

TRUNK: Opens the TRUNK or activates the AUX 3

output.

Note: Trunk option must be installed.

START/STOP: Remote starts or stops the engine.

Gets the system into Cold Weather mode by

pressing the SHIFT

button and then pressing and

holding the START/STOP button for 3

seconds.

Note: Icon may vary.

AUX

AUX (upper right side): This button serves as a

second function button.

This button allows assigning different functions to

any of the other four buttons.

Vehicle Presets

Heater

When leaving the vehicle it is recommended to preset the accessory controls in preparation for the

next remote start. Settings for the blower motor (fan), front and rear, should not be left on HIGH. It

is recommended to leave the settings on LOW or MEDIUM instead.

Windshield Wipers & Radio & Headlights

Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to become

energized while running under remote start. When leaving the vehicle you must ensure that the

windshield wiper and headlight switches are OFF. Leaving the headlight switch ON on certain

types of vehicles could cause them to remain ON even after remote starter shut down, resulting in

a dead battery.

P.16 User Guide

Vehicle Status Request

The status request feature allows the user to see the status of the vehicle i.e.: if the doors are

locked or unlocked or if the vehicle is in cold weather mode, home valet mode, in valet mode or

how much time is left in the run time cycle. The following charts (Tables 1, 2 and 3) indicate the

confirmation sequences.

To retrieve the vehicle status:

Press and release the AUX button then press and release the button (there will be a beep).

The transmitter will then flash the corresponding sequence of LED’s depending on the vehicle’s

status.

xIf the engine is NOT running

xIf the vehicle is in or out of ready mode

xIf the engine IS running under a remote start (if the doors are locked)

or (if the doors are unlocked).

The status request feature is a two-step procedure:

xThe first sequence of flashes denotes if the vehicle’s doors are locked or unlocked.

xThe second sequence of flashes (if applicable) denotes if the vehicle is Cold Weather mode,

Home valet mode, or, Valet mode.

xIf there is no second sequence transmission, then the vehicle is none of the 3 mentioned

features (Cold weather mode, Home valet mode or Valet mode).

Status Request When the Engine IS NOT Running

STATUS

SEQUENCE

LOCK

UNLOCK

TRUNK

START/STOP

Beep(s)

Lock

3 flashes

Unlock

3 flashes

Cold

Weather

1st sequence

if locked

3 flashes

1st sequence

if unlocked

3 flashes

2nd sequence

1 second

Home

Valet

1st sequence

if locked

3 flashes

1st sequence

if unlocked

3 flashes

2nd sequence

1 second

Valet

Mode

1st sequence

if locked

3 flashes

1st sequence

if unlocked

3 flashes

2nd sequence

1 second

User Guide P.15

Multi-car Operation

This option allows the owner of two vehicles, both equipped with the same Remote Car Starter

model, to control both systems with a single remote control.

To control the second vehicle:

Press TRUNK + LOCK buttons simultaneously:-------------------------------------------------------LOCK

Press TRUNK + UNLOCK simultaneously:-------------------------------------------------------------UNLOCK

Press TRUNK + START/STOP simultaneously: -------------------------------------------------------START

Press TRUNK + START/STOP simultaneously: -------------------------------------------------------STOP

Press AUX ¾

¾AUX ¾TRUNK:-----------------------------------------------------------------------------TRUNK

Press AUX ¾AUX ¾LOCK:-------------------------------------------------------------------------------LOCK

Press AUX ¾AUX ¾UNLOCK: --------------------------------------------------------------------------UNLOCK

Press AUX ¾AUX ¾START/STOP: --------------------------------------------------------------------START

Press AUX ¾AUX ¾START/STOP: --------------------------------------------------------------------STOP

Press AUX ¾AUX ¾TRUNK:-----------------------------------------------------------------------------TRUNK

Note: If the multi-level features have been modified from their default state by your installer, the

AUX button may have to be pressed once, twice or three times, according to the option you chose.

OEM-Style Alarm

The OEM-style alarm (if configured by your installer) monitors the doors, hood and ignition switch

of your vehicle. It will sound the horn if a door or the hood is opened, or if the key is turned into the

IGNITION ON position.

xTo arm the OEM-style alarm, press the button on the transmitter.

-The OEM-style alarm will ONLY arm if the button on the transmitter is pressed.

The LED on the antenna will flash slowly to indicate that the OEM-style alarm is now armed.

xTo disarm the OEM-style alarm, press the button on the transmitter.

-To stop the horn from sounding if the OEM-style alarm is triggered, press the or

button, or put the system in and out of Valet Mode (See page 9).

Intrusion Codes via horn

The system monitors the following:

xDoors

xHood

xIgnition

Note: If an intrusion has occurred the HORN will sound for a maximum of 1 minute.

If an intrusion has occurred and pressed, the horn provides an intrusion code corresponding to

the type of intrusion that occurred.

1x = power interruption

4x = Doors intrusion

3x = Hood

6x = Ignition

P.6 User Guide

Arming and disarming the starter kill (if installed)

This added security feature will prevent the vehicle from starting with the Ignition key when the

starter kill is armed. If the system was installed with the starter kill option, the vehicle will not be

able to start with the key unless the system has been unlocked first or put into Valet Mode

(page 9).

Note: If the Starter Kill is installed, the vehicle will benefit from a protection against starter motor

damage that could occur after remote-starting the engine should the user, by force of habit, turn

the ignition key to the CRANK position.

The Starter Kill (if installed) can be configured by the installer either to Passive Mode (so as to arm

automatically) or Active Mode (so as to require the user’s intervention for arming). By default, the

Remote Car Starter is configured to Passive Mode.

Passive mode:

To arm the Starter Kill:

xPress the button on the transmitter.

xLet the Starter Kill arm automatically 1 minute (by default) or 3 minutes (if configured this way)

after the ignition is turned OFF or once the last door is closed (if the doors are monitored). The

parking lights will flash once.

xThe LED on the antenna will flash quickly during the countdown preceding the activation

of the Starter Kill.

xOnce the activation countdown expires, the LED will send a series of quick double

flashes to indicate that the Starter Kill is now armed.

To disarm the Starter Kill:

xPress the button on the transmitter.

xThe Starter Kill will automatically rearm itself after 1 minute (by default) or 3 minutes (if

configured this way) if no door is left opened (if the doors are monitored) and the ignition

is not turned ON.

Active Mode:

To arm the Starter Kill:

xPress the button on the transmitter.

xThe parking lights will flash once.

xThe LED on the antenna will flash slowly.

xIf remote door locks are installed, this will also lock the doors and arm the OEM-style

alarm (if configured).

To disarm the Starter Kill:

xPress the button on the transmitter.

xThe parking lights will flash twice.

xThe LED on the antenna will remain OFF.

xIf remote door locks are installed, this will also unlock the doors and disarm the OEM-

style alarm (if configured).

User Guide P.7

Remote-Starting Your Vehicle

Setting Your Vehicle into Ready Mode

If your vehicle has a manual transmission you must read the following indications. In order to start

the vehicle by remote, the unit must first be set to Ready Mode. If the unit is not set to Ready

Mode, it cannot remote start the vehicle.

Please note that Ready Mode can be enabled by the remote or the handbrake, depending on the

option that was selected by your installer. Therefore, you must follow the appropriate procedure

between the two described below in order to set your vehicle into Ready Mode.

Once the system is set to Ready Mode, the vehicle can be remote started and stopped at any time.

The system will exit Ready Mode if a door, the hood or the trunk is opened, if the brake pedal is

pressed, if the parking brake is disengaged or if the ignition key is turned to the IGNITION ON

(RUN) position.

To set the system to Ready Mode:

If Ready Mode is enabled by remote

If Ready Mode is enabled by handbrake

1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the neutral

position.

2. With the engine running, apply the parking brake

once and release the brake pedal.

3. Within 20

sec. of engaging the parking brake,

press and hold , or

on the

transmitter (SmartStart™ uses only

the

SmartStart™ icon).

The parking lights will flash 3

times quickly and

remain lit. Release the button.

2. With the engine running, apply the parking brake

twice within 10 sec.

3. Make sure to release the brake pedal.

The parking lights will flash 3

times quickly and

remain lit.

4. Remove the key: the engine will keep on running.

5. Exit the vehicle. All doors should be closed, including the hood and trunk.

6. THERE ARE THREE POSSIBLE OPTIONS TO COMPLETE READY MODE (programmable by installer)

OPTION 1: No lock

OPTION 2: Manual shut down

(default)

OPTION 3: Automatic shut

down

The engine stops.

The engine keeps going until you

press either;

to lock the doors and shut

down the engine;

to unlock the doors and shut

down the engine;

to shut down the engine

without affecting the doors.

The engine runs for 8 sec. then

locks the doors before

finally

shutting down the engine, without

user interaction.

WARNING: The vehicle is not

armed or locked down.

WARNING: Engine runs until the pre-

programmed run time expires.

WARNING: Do not leave your

keys in the vehicle!

7. The Parking lights will flash twice to indicate Ready mode is set.

Remote-starting

1. Press the button for approximately 1 second and release.

2. The remote will beep once.

3. The remote will confirm the remote starter’s activation by beeping 3 times.

If your vehicle does not start at the first attempt, the system will shut down, wait a few seconds and

try to start the engine again. There will be 3 start attempts before the system gives up.

P.14 User Guide

“Home ValetTM” Mode

If configured at installation, this feature will remotely set the vehicle to a no-remote-start mode: if

the vehicle is parked indoors there is no danger of it starting accidentally by remote control. If the

vehicle has a manual transmission, it should be set into ready mode before activating the Home

Valet™.

Note: Once the Home Valet Mode is activated, the vehicle will not start by remote, but the OEM

alarm functions will remain active.

To take the system into home valet mode:

1. Press the or button.

2. Within 3 seconds, press the and buttons simultaneously until the remote

beeps twice.

To take the system out of home valet mode:

xTurn the ignition key to the IGNITION ON (RUN) position.

The system will warn you if someone attempts to start your vehicle while it stands

in home valet mode. The parking lights will:

xTurn ON then OFF; then

Flash twice, pause; then

Flash twice again.

AUX 1

Note: This 500 mA negative Aux 1 output can be used for many different applications

Priority door:

This great feature allows the user to unlock solely the driver’s door with a single press of the

button on the transmitter, and to unlock the other doors, if desired, by pressing the button for a

second time.

The output will provide a 1-second negative output when the button is pressed a second time

on the transmitter.

Horn Confirmation:

AUX 1 can be programmed to trigger the horn every time the button is pressed, or when the

button is pressed twice within 3 seconds. When horn confirmation is activated, panic mode is

enabled. If horn confirmation is disabled, panic mode will not be available.

AUX 2

If configured at installation, this feature can be activated by pressing the AUX (or Shift) button,

followed by pressing and holding the lit up button to activate AUX 2.

Horn Timing Adjustment

The pulse duration can be configured by your installer (from 5 ms to 200 ms).

User Guide P.13

Safe Start

This feature will eliminate accidental remote starts, e.g. when children are playing with the

transmitter.

Safe start enabled: If this feature is enabled, the user must press the button twice within

3 seconds to remote-start the vehicle.

Swap start (2-way remote): If this feature is enabled;

1. Press and release the AUX button.

2. The button on the transmitter will light up.

3. While it is lit, press to remote start the car.

The AUX 2 output can be activated by pressing the button.

Swap start (1-way remote): If this feature is enabled;

1. Rapidly press AUX twice. The remote’s LED will start flashing.

2. While the LED is flashing, press to remote start the car.

The AUX 2 output can be activated by pressing the button.

Engine Run Time

If you have a gas engine, your Remote Car Starter can be programmed to run the engine for 3, 15,

or 25 minutes (15 minutes by default). If you have a diesel engine, the Remote Car Starter can be

programmed to run the engine for 8, 20, or 30 minutes (20 minutes default).

Turbo Mode

If Turbo Mode is configured at installation, it will allow a turbocharger to idle down after the user

leaves the vehicle: the unit will take over the vehicle and keep it running for 60 seconds (or until it

is shut down by remote control), then shut down the engine.

If your vehicle has an automatic transmission, proceed as follows to set the system to Turbo Mode:

1. With the engine running, make sure to release the brake pedal and press the ,

or button on the transmitter until the parking lights come ON.

Note: SmartStart™ can be setup to use the SmartStart™ icon to activate Turbo

mode.

2. Remove the ignition key from the ignition switch. The engine will continue running.

3. Exit the vehicle and close all doors, hood and trunk.

4. Press the button; this will lock the doors, arm the OEM-style alarm (if

configured) and confirm that the vehicle is in Turbo Mode.

5. The engine will shut down after 60 seconds.

If your vehicle has a manual transmission, follow all steps of the Ready Mode routine (page-7) to

activate Turbo Mode. At the last step, press either:

xto lock the doors and have the engine shut down after 60 seconds;

The parking lights will flash 3 times and remain lit.

The OEM-style alarm and starter kill (if configured) will be armed.

xto unlock the doors and have the engine shut down after 60 seconds;

The parking lights will flash 3 times and remain lit.

xto shut down the engine without affecting the doors.

Note: The vehicle will enter Ready Mode once the engine run time expires.

P.8 User Guide

Driving Off

With the vehicle running remotely, press the button to disarm the starter kill (if installed) and

unlock the doors. Enter the vehicle and do the following:

1. Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the CRANK

position while the engine is running. This would cause the starter motor to re-engage.)

2. Press the brake pedal to disengage the remote starter unit.

You are now ready to drive off.

Note: On some Push-To-Start (PTS) vehicles, no takeover is possible as pressing the brakes will

shut the engine down. Please talk to your technician to determine if the “Takeover mode” can be

set for your vehicle.

Remote Starter Features

Remote Door Locks

If your Remote Car Starter was installed with the Remote Door Locks option, you will have the

convenience of remote keyless entry.

To LOCK your doors and ARM the system:

1. Press and hold the button for approx. 1 sec.

2. The remote will beep once to confirm locking of the doors.

To UNLOCK your doors and DISARM the system:

1. Press and hold the button for approx. 1 sec.

2. The remote will beep twice to confirm unlocking of the doors.

Remote Trunk Release

If your system was installed with the Remote Trunk Release option, you can open your trunk by

pressing the button until the remote beeps once. In addition, this will also disarm the OEM-

style alarm (if installed).

Idle Mode

Convenience feature: Idle Mode allows you to keep the engine running and the doors locked

while you stop, for example, at a convenience store or for a short delivery.

This feature allows you to let the remote starter take over control of the vehicle (i.e. no Key in the

Ignition Switch) while the engine is running.

Activating Idle mode (Automatic transmission):

1. With the engine running, make sure to release the brake pedal and press the ,

or button on the transmitter until the parking lights come ON.

Note: SmartStart™ can be setup to use the SmartStart™ icon to activate Idle mode.

2. Remove the ignition key from the ignition switch.

The engine will continue running.

3. Exit the vehicle. All doors, the hood and trunk should be closed

4. Press the button to lock the doors, to arm the starter kill and to arm the alarm (if

available). The engine will continue running.

a. When re-entering the vehicle, the user must reinsert the key into the ignition and

turn it to the ON position (not Crank) without pressing on the brake.

User Guide P.9

b. Once the key is in the ON position, press on the brake pedal to put the

transmission in gear. Pressing the brake pedal at this step will cancel the remote

starter takeover.

c. Drive off.

If your vehicle has a manual transmission, Idle Mode can be activated through the same routine as

that used for Ready Mode (page 7); at the last step, press the button to lock the doors, arm

the system and leave the engine running.

NEW FEATURE – Push-To-Start Idle Mode

This feature is a variation of “Idle mode”, but made specifically for Push-To-Start vehicles, with

automatic or manual transmissions. (Consult your installer for availability of this feature.) Follow the

same steps as the normal Idle Mode procedure, except for when re-entering the vehicle while the

engine is running;

1. Press unlock

2. Open then close all doors.

3. You have 1.5 minutes (or 3 minutes) to press on the brake pedal, to get in gear and

drive off.

Note 1: Pressing on the brake pedal after the allocated (1.5 or 3-min.) period will shut the engine

down.

Note 2: The engine will continue running until the user re-enters the vehicle or until the expiration

of the run time.

Note 3: If the pre-programmed run-time expires or if the user shuts down the engine remotely, the

vehicle will enter Ready Mode automatically (manual transmissions only).

Caution!! Do not leave children or pets unattended in a vehicle standing in Idle Mode.

Valet Mode

When the vehicle is in Valet Mode, the remote starter and alarm functionalities are disabled. If the

vehicle needs to be serviced, or if you park it indoors, Valet Mode will prevent the engine from

being remote-started accidentally.

Any of the following features will put the remote car starter into Valet Mode:

Ignition Valet: This feature allows you to set Valet Mode using the ignition key.

Remote valet: This feature allows you to set Valet Mode using the transmitter.

To put the system into Valet Mode

Using the KEY (Ignition Valet Mode):

1. Insert the ignition key into the ignition switch. Within 10 sec., cycle the ignition key to the

IGNITION/RUN and OFF positions 5 times until the parking lights flash 3 times.

2. Turn the ignition OFF.

3. The LED on the antenna will stay ON indicating that the vehicle has successfully entered

Valet mode.

Using the TRANSMITTER (Remote Valet Mode):

1. Press and hold the and buttons simultaneously until the remote beeps once, pauses,

then beeps once again. Release the buttons.

2. The and buttons will flash 3 times.

3. The LED on the antenna will stay ON indicating that the vehicle has successfully entered

Valet mode.

P.12 User Guide

Feature Confirmation Chart

Feature

LOCK

UNLOCK

TRUNK

START/STOP

Beep(s)

Lock

3 flashes

Unlock

3 flashes

Trunk

3 flashes

LED ON/OFF

3 flashes

Start

3 flashes

Running

3 flashes

Stop

3 flashes

Entering Cold

Weather Mode

3 flashes 2

Exiting Cold

Weather Mode

3 flashes 1

Home Valet

3 flashes

Valet Mode

3 flashes

Exit Valet Mode

3 flashes

Fail Start Attempt

4 flashes

Advanced Features: Installation-programmable Options

The remote car starter was designed with flexibility and OEM integration in mind. With its program-

mable options, this unit can single-handedly control nearly any electrical system in your vehicle.

Caution: The programming of your system should be left to a professional. Changing any one of

the settings may affect the operation of your Remote Car Starter.

Ignition-controlled Door Locks

This is an added security feature. If your Remote Car Starter was installed with the Ignition-

Controlled Door Locks option, the doors will automatically lock as soon as the ignition key is turned

to the IGNITION ON (RUN) position while the brakes are pressed. The remote car starter will also

lock any door that was unlocked and opened (then closed) the next time the brake pedal is pressed

(only when doors are monitored). When the key is turned to the OFF position, the doors will

automatically be unlocked.

Secure Lock

(Disabled by default.) Before your vehicle can be remote-started, the factory security system must

first be disarmed. The Secure Lock feature may be required on certain vehicle models with factory

security systems that automatically unlock the doors when the security system is disarmed.

To keep your vehicle protected when the factory security system is disarmed for a remote start,

Secure Lock will relock your doors as soon as the vehicle is started. Once the engine is shut down

by remote or after its runtime has expired, Secure Lock will also rearm your factory security system

and relock the doors.

User Guide P.11

To enter Cold Weather Mode (1-way remote):

1. Rapidly press AUX twice. The remote’s LED will start flashing.

2. Press and hold until the parking lights will flash for 2 seconds, pause, and then flash

3 times.

To exit Cold Weather Mode, do any one of the following actions:

xOpen the hood.

xStart the engine remotely.

xTurn the ignition key to the IGNITION ON (RUN) position.

xPress and release the AUX button.

a. The button on the transmitter will light up.

b. While the button is still lit, press and hold the button until the remote

beeps once, pause, then beeps once again.

c. Release the button. Its LED will flash quickly.

x(1-way remote) Rapidly press AUX twice. The re mote’s LED will start flashing. Press

and hold until the parking lights flash for 2 seconds, pause, and then flash twice.

To verify whether the system is in Cold Weather Mode:

x(Automatic transmissions only) Press the brake pedal: If the vehicle is in Cold Weather

mode, the parking lights will remain ON while the brake pedal is pressed.

xDo the vehicle status request feature (page-16).

Extended Run Time

While the vehicle is running under a remote start, press and hold the button until the remote

beeps. This will reset the run time counter to zero and restart the run time cycle from the beginning.

Note: The extended run time procedure can only be carried out once per remote start.

To stop the vehicle, at any moment, simply press and release the button.

Example: If your remote car starter is programmed for a run time of 3 minutes and your vehicle

has been running for 2 minutes already, pressing the button will reset the counter to zero and

allow the engine to run for another cycle (in this case, 3 minutes).

Disable/Enable LED flashing

To disable the LED: Press and simultaneously until the remote beeps once, pauses for

2 seconds, then beeps once again. Release the buttons. The parking lights will flash 3 times.

To Enable the LED: Press and simultaneously until the remote beeps once, pauses for

2 seconds, then beeps once more. Release the buttons. The parking lights flash once.

Constant output

Pressing and holding the button for more than 3 seconds will lock all doors and will send a

constant pulse as long as the button is held down (maximum of 15 seconds). This constant

pulse can be configured to activate certain functionalities such as rolling up the windows – Please

refer to your installer to see if your vehicle is compatible with this option.

Pressing and holding the button for more than 3 seconds will unlock all doors and will send a

constant pulse as long as the button is held down (maximum of 15 seconds). This constant

pulse can be configured to activate certain functionalities such as rolling down the windows –

Please refer to your installer to see if your vehicle is compatible with this option.

P.10 User Guide

To take the system out of Valet Mode

Using the KEY (Ignition Valet Mode):

1. Insert the ignition key into the ignition switch. Within 10 sec., cycle the ignition key to the

IGNITION/RUN and OFF positions 5 times until the parking lights flash twice.

2. Turn the ignition OFF.

3. The LED on the antenna will flash rapidly, indicating that the vehicle is now out of Valet

mode.

Using the TRANSMITTER (Remote Valet Mode):

1. Press and hold the and buttons simultaneously until the remote beeps once, pauses,

then beeps once again. Release the buttons.

2. The and button will flash 3 times.

3. The LED on the antenna will flash rapidly, indicating that the vehicle is now out of Valet

mode.

If someone has attempted to remote-start the vehicle while in Valet Mode; the parking lights will

turn ON, then OFF, then flash twice.

Panic Mode

Note: Panic mode can only be activated if the horn has been adequately configured by the

installer.

In an emergency situation, you can activate panic mode by pressing and holding the AUX button

until the horn starts honking. If the vehicle is under a remote start, the engine will shutdown

automatically before setting off the horn. You can stop the horn by pressing:

(this will lock your doors and deactivate panic mode),or

(this will unlock your doors and deactivate panic mode).

Furthermore, the panic mode can be stopped by activating Valet Mode (page-9)

* Panic Mode will automatically shut down after 30 sec.

Quick LockoutTM

(Also called Secure Panic.) For fast protection in emergency situations, the system will LOCK all

doors when you press the brake pedal while you hear the Horn sounding. (Quick Lockout is only

available when Panic mode has been triggered.)

Cold Weather Mode

If the vehicle has a manual transmission, Ready mode (page-7) should be set before entering

Cold Weather Mode. When Cold Weather Mode is active, the engine starts every 2 hours and runs

for 3 minutes (or for 8 or 20 minutes with diesel engines). Cold Weather Mode automatically ends

after 24 hours (or 12 starts).

To enter Cold Weather Mode (2-way remote):

1. Press and release the AUX button.

2. The button on the transmitter will light up.

3. While the button is still lit, press and hold the button until the remote beeps

once, pause, then beeps twice.

4. Release the button. Its LED will flash quickly.

Tabla de contenidos

Otros manuales de Arranque remoto de Smart Start

Smart Start

Smart Start AS-1880FM Manual de usuario

Smart Start

Smart Start AS-2471TW-FM Manual de usuario

Smart Start

Smart Start AS2272 Manual de usuario

Smart Start

Smart Start AS-2780U Manual de usuario

Smart Start

Smart Start GS-2260TW Manual de usuario

Smart Start

Smart Start ns1074 Manual de usuario

Smart Start

Smart Start BC-11 Manual de usuario

Manuales populares de Arranque remoto de otras marcas

AstroStart

AstroStart 803U Manual de usuario

Durite

Durite 0-649-20 Manual

EINHELL

EINHELL BT-PS 1000 Manual

Linear

Linear ACCESS AK-21 Especificaciones técnicas

Soundstream

Soundstream TARANTULA RS.2 Manual de usuario

Jaycar Electronics

Jaycar Electronics MB3752 Manual de usuario

Ultra Start

Ultra Start 72 Series Manual de usuario

ADS

ADS FLASHLOGIC FLRSVW1 Manual de usuario

Selecta

Selecta JS012 Manual de usuario

Black Widow Security

Black Widow Security BW RAS 400 Manual de usuario

Vector

Vector Power City DK080706 Suplemento

Code Alarm

Code Alarm CA-535 Manual de usuario

Ozito

Ozito OJS-800 Manual de usuario

Profi-Partner

Profi-Partner 46387 Manual de usuario

EZ STARTER

EZ STARTER EZ-45 Manual de usuario

Viper

Viper 4204 Manual de usuario

Essex Electronics

Essex Electronics KE-1701 Manual de usuario

EINHELL

EINHELL EGS 3600 Manual