Smart Start AS-2471TW-FM Manual de usuario

TWO-WAY 6-BUTTON LCD

AUTOMATIC/MANUAL TRANSMISSION

REMOTE STARTER

INDUSTRY CANADA USER NOTICE:

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired operation of

the device.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen

that the equivalent isotropically radiated power (EIRP) is not more than that required for successful

communication.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized

modifications to this equipment. Such modifications could void the user's authority to operate the

equipment

AS-2471TW-FM

/AS-2472TWU

User Guide

WARNING

It is the responsibility of the vehicle operator to ensure their vehicle is parked

in a safe and responsible manner.

1. a) Manual transmission: When leaving the vehicle, it is the user’s responsibility

to ensure that the gearshift lever is in the NEUTRAL position and the parking

brake is engaged in order to avoid accidents upon remote starting.

b) Automatic transmission: When leaving the vehicle, it is the user’s

responsibility to ensure that the gearshift lever is in “Park” in order to avoid

accidents upon remote starting.

(Note: Make sure that the automatic vehicle cannot start in "Drive".)

2. It is the user's responsibility to ensure that the remote starter is disabled or put

into valet mode before servicing.

A note concerning the battery inside the transmitter:

Depending on your usage of the transmitter, the battery can last anywhere between 3 to 6 months. When the

battery is low, the transmitter will produce two beeps in a repetitive cycle. At that point you should replace

your battery with a new one. That is why we recommend that you keep a spare battery somewhere handy

such as the glove compartment.

Designed & engineered in Canada

P.2 User Guide

TableofContents

Government regulations..................................................................................................................3

Introduction with SmartStart™ .............................................................................................3

Vehicle Presets.................................................................................................................................4

Heater ............................................................................................................................................4

Windshield Wipers, Radio & Headlights........................................................................................4

Using the Transmitter ......................................................................................................................4

LCD Transmitter basic confirmations ............................................................................................5

Basic Vehicle Operations...............................................................................................................5

Backlight............................................................................................................................................6

Remote’s advanced functions and MENU......................................................................................6

How to access default advanced remote functions and MENU.....................................................6

Remote-Starting Your Vehicle.........................................................................................................9

Setting Your Vehicle Into Ready Mode..........................................................................................9

Remote-starting............................................................................................................................10

Driving Off....................................................................................................................................10

Arming and disarming the starter kill (if installed) .....................................................................10

Remote Starter Features................................................................................................................11

Remote Door Locks.....................................................................................................................11

Remote Trunk Release................................................................................................................12

Idle Mode .....................................................................................................................................12

Valet Modes.................................................................................................................................13

Panic Mode..................................................................................................................................13

Quick Lockout

...........................................................................................................................14

Cold Weather Mode.....................................................................................................................14

Extended Run Time.....................................................................................................................14

Disable/Enable LED flashing .......................................................................................................15

Temperature Request (If ACC-Temp-100 installed)....................................................................15

Advanced Features: Installation-programmable Options..........................................................15

Ignition-controlled Door Locks .....................................................................................................15

Secure Lock.................................................................................................................................15

Safe Start.....................................................................................................................................15

Engine Run Time .........................................................................................................................16

Turbo Mode..................................................................................................................................16

“Home Valet

” Mode ..................................................................................................................16

AUX 1...........................................................................................................................................17

Horn Chirp Timing........................................................................................................................17

Multi-car Operation.......................................................................................................................17

OEM-Style Alarm.........................................................................................................................18

Intrusion Codes via horn..............................................................................................................18

Missing a Start or a Stop Confirmation........................................................................................18

Multi-Level Features.......................................................................................................................19

Troubleshooting Transmitting Range ..........................................................................................20

Diagnostics – Parking Light Flash Table .....................................................................................20

User Guide P.3

Governmentregulations

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

This device complies with the Industry Canada Radio Standards Specification RSS 210. Its use is

authorized only on a no-interference, no-protection basis; in other words, this device must not be

used if it is determined that it causes harmful interferences to services authorized by IC. In

addition, the user of this device must accept any radio interface that may be received, even if this

interference could affect the operation of the device.

Warning! Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate this device.

IntroductionwithSmartStart™

This is a state-of-the-art remote car starter system. The system is packed with advanced features

such as priority access to the driver’s door (commodity features), the Safe Start children safety

feature and SmartStart™.

SmartStart™ is a groundbreaking technology that enables your remote starter features to be

accessed by your smartphone. Features include keyless entry, trunk release, panic, remote

start/stop toggle and alarm notifications

. Note: SmartStart™ must be professionally installed. For

more information, see your nearest authorised Directed Canada dealer.

With many advanced functions, this product will satisfy any one of your expectations from high-end

commodity and security systems, without neglecting any standard feature commonly offered by

entry-level starters.

Certain conditions apply. See your authorised Directed Canada dealer.

P.4 User Guide

VehiclePresets

Heater

When leaving the vehicle it is recommended to preset the accessory controls in preparation for the

next remote start. Settings for the blower motor (fan), front and rear, should not be left on HIGH. It

is recommended to leave the settings on LOW or MEDIUM instead.

WindshieldWipers,Radio&Headlights

Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to become

energized while running under remote start. When leaving the vehicle you must ensure that the

windshield wiper and headlight switches are OFF. Leaving the headlight switch ON on certain

types of vehicles could cause them to remain ON even after remote starter shut down, resulting in

a dead battery.

UsingtheTransmitter

Your remote starter is equipped with a 6-button multi-channel remote control. It can operate two

independent vehicles equipped with identical remote starters (see Multi-car operation section on

page 17).

The functions of the 2-way transmitter are as follows:

LOCK:

Locks the doors and arms theSTARTER KILL (if installed).

UNLOCK:

Unlocks the doors and disarms the STARTER KILL (if

installed). Activates the AUX 1 output if Priority Door Access is

configured.

TRUNK:

Opens the TRUNK or activates the AUX 3 output.

Note: Trunk option must be installed.

START:

Remote starts the engine. Gets the system into Cold Weather

mode if pressed for longer than 3 seconds.

Note: Icon may vary.

FUNCTION button

Turns the backlight ON, allows access to the Multi-level

functions and to the Menu.

AUX button (if programmed):

Activates AUX 2 output, stops the engine, requests

Temperature, activates Panic mode or activates Cold Weather

mode.

User Guide P.5

The functions of the 1-way transmitter are as follows (optional):

LOCK: Locks the doors and arms the

STARTER KILL (if installed).

(Image as reference only)

UNLOCK: Unlocks the doors and disarms the

STARTER KILL (if installed). Activates the

AUX 1 output if Priority Door Access is

configured.

TRUNK: Opens the TRUNK or activates the

AUX 3 output.

Note: Trunk option must be installed.

START/STOP: Remote starts or stops the

engine. Gets the system into Cold Weather

mode by pressing the AUX button and then

pressing and holding the START/STOP button

for 3 seconds. Note: Icon may vary.

AUX

AUX: This button serves as a second function

button.

This button allows assigning different functions

to any of the other four buttons.

LCDTransmitterbasicconfirmations

BasicVehicleOperations

Function Button pressed

Icon / text

Sound

Instructions /description

Lock / LOCK 1 beep Lock and arm the system

Unlock / UNLOCK 2 beeps Unlock and disarm the system

Trunk or Aux 3 TRUNK 1 beep Trunk output

Start 0:15+ (default) 3-beeps Start the engine

Stop None 2-beeps Stop the engine

Back light On for 5 seconds Press for 1 sec then release

Cold Weather

mode , then

(default) 1 beep See Cold Weather Mode section

(page-14)

Remote Valet + 1 beep See Valet

mode section

(page-12)

Panic or for

longer than 5 sec.

None 1 beep

See Panic Mode section

(page-13)



P.6 User Guide

Backlight

Three different ways to use the backlight:

•Turning the backlight on for 3 seconds, press the for at least 1 second and

release.

•If the button is pressed and held for more than 5 seconds the backlight will stay ON

as long as the button is held.

•To browse the MENU while the backlight is ON:

a) Press the for at least 1 second and release. The backlight should

turn ON.

b) Within 3 seconds, press the button for 2 seconds to access the

various functions.

Remote’sadvancedfunctionsandMENU

HowtoaccessdefaultadvancedremotefunctionsandMENU

User

Transmitter

(default)

1.Press for 1 second and release ÎRemote beeps once and L-01

appears on screen.

2.Press a 2nd time for 1 second and release ÎRemote beeps once and L-02

appears on screen.

3.Press a 3rd time for 1 second and release ÎRemote beeps once and L-03

appears on screen.

4.Press a 4th time for 1 second and release ÎRemote beeps once and MENU

appears on screen.

5.At that point, press to enter the remote’s

MENU. ÎFollow the steps listed below in

“Selecting and adjusting

advance MENU options”:

Note: The order of LEVELS and MENU can be re-arranged in the menu option FBPRO.

Selecting and adjusting advanced menu options:

•When in MENU, press button to enter the menu.

•Press button to move up in the menu or button to move down in the

menu.

•Press button to select the option you would like to adjust

•Press button to increase the value or to activate or deactivate a function

or toggle through the selection.

•Press button to decrease the value or to activate or deactivate a function

or toggle through the selection.

•Press button to move to the next sub-option or go back to the main menu.

•To SAVE modifications and EXIT remote’s MENU, do not touch any button for

approximately 5 to 10 seconds.

User Guide P.7

Remote’s advanced functions and MENU

Display Description

PARK

(1)

Parking meter countdown

This version of the countdown feature is particularly useful for keeping track of

parking meter time: the user may quickly set up the countdown using the Parking

Menu. The transmitter will beep once, 5min before the Parking countdown reaches 0

and beeps 6 times once the countdown expires.

Through Advanced Options, first press to select MENU, then:

a. Choose PARK and press .

b. Set the time at which you want set the alarm. First set the hour, and

press . Then set the minutes and press .

c. Choose ON and wait. A flashing “P” will appear on screen to

confirm activation.

ALARM

(2)

Alarm Clock

The LCD remote control has a built-in alarm clock, which can be set up using the

Alarm Clock Menu. Once the programmed time is reached, the remote will beep 6

times every minute until a button is pressed.

Through Advanced Options, first press to select MENU, then:

a. Choose ALARM and press .

b. Set the time at which you want to set the alarm. First set the hour,

and press . Then set the minutes and press .

c. Choose ON and wait. A flashing “A” will appear on screen to

confirm activation.

CWM

(3)

Cold weather mode

function:

Through Advanced Options, first press to select MENU, then:

a. Choose CWM and press .

b. Choose ON/OFF, then press and hold until icon appears.

VALET

(4)

Valet function:

Through Advanced Options, first press to select MENU, then:

a. Choose VALET and press .

b. Choose ON/OFF, then press and hold until icon appears.

TSTART

(5)

Time start function:

This feature is used to remote start the car at a pre-programmed time. Once the pre-

programmed time is reached, the remote will send a start command to the car

module. (Note: For this feature to work, remote has to be within range of the vehicle).

Through Advanced Options, first press to select MENU, then:

a. Choose TSTART and press .

b. Set the time at which you want to remote start the vehicle. First set

the hour, and press . Then set the minutes and press .

c. Choose ON and wait. A flashing “T” will appear on screen to confirm

activation.

SECUR

(6)

Secure:

This feature is used to lock the keypad of the transmitter to avoid accidental button

press. When the keypad is locked and a button is pressed, the LCD will display

“PRESF” for 1 second and goes back to the clock.

The transmitter keypad can also be locked as follows:

a. Press to select MENU.

P.8 User Guide

b. Within 3 seconds, press .

c. The LCD will display “Security” to confirm locking of the keypad.

•Press for about 1sec, to unlock the transmitter’s keypad.

COLOR

(7)

Backlight color

The backlight can be set to 8 different colors.

Through Advanced Options, first press to select MENU, then:

a. Choose COLOR and press .

b. Choose the desired color by pressing or

LCD

(8)

LCD:

If there is no activity within the programmed time, LCD screen will automatically turn

off after 1 min, 15 min, 30 min, 60 min or always ON. This feature maximizes the

lifetime of the battery.

CLOCK

(9)

Clock:

The Clock menu is used to set the current time on your remote control.

Through Advanced Options, first press to select MENU, then:

a. Choose CLOCK and press .

b. Set the time at which you want to set the clock. First set the hour,

and press , then set the minutes and press .

TEMP

(10)

Temp

Can be set to read the temperature in Celsius (CTEMP) or Fahrenheit (FTEMP)

LANGU

(11)

Language

Can be set to either English or French

SBPRO

(12)

Side button function:

The side button can be programmed as:

•Panic button;

•Stop button;

•Temperature request button;

•Aux 2 output button;

•or CWM (Cold Weather Mode).

KEYLOC

(13)

Keypad lock

Note: In order for this feature to work, “Secure function” must be set to ON.

If there is no activity within the programmed time, the keypad will automatically lock

after 5 seconds, 10 seconds or 20 seconds.

•Press for about 1sec, to unlock the transmitter’s keypad.

ILLUM

(14)

LCD illumination:

When this function is enabled, the LCD will illuminate each time LOCK, Unlock or

START is activated.

User Guide P.9

FBPRO

(15)

Button Function:

The order of LEVELS and MENU can be re-arranged using the Button Function

Menu. Details on (page-18).

F Button Function

Menu FBPRO Function Button Programming

Function Button

programming

1 2 3

2 3 1 M

3 1 2 M

2 1 3 M

M 1 2 3

Level 1, level 2, level 3, MENU

Level 2, level 3, level 1, MENU

Level 3, level 1, level 2, MENU

Level 2, level 1, level 3, MENU

MENU, level 1, level 2, Level 3

RemoteStartingYourVehicle

SettingYourVehicleIntoReadyMode

If your vehicle has a manual transmission you must read the following indications. The unit must

first be set to Ready Mode in order to start the vehicle by remote. If the unit is not set to Ready

Mode, it cannot remote start the vehicle. Please note that Ready Mode can be enabled by the

remote or the handbrake, depending on the option that was selected by your installer. Therefore,

you must follow the appropriate procedure between the two described below in order to set your

vehicle into Ready Mode.

Once the system is set to Ready Mode, the vehicle can be remote started and stopped at any time.

The system will exit Ready Mode if a door, the hood or the trunk is opened, if the brake pedal is

pressed, if the parking brake is disengaged or if the ignition key is turned to the IGNITION ON

(RUN) position.

To set the system to Ready Mode:

If Ready Mode is enabled by remote If Ready Mode is enabled by handbrake

1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the

neutral position.

2. With the engine running, apply the parking

brake once and release the brake pedal.

3. Within 20 sec. of engaging the parking

brake, press and hold , or on

the transmitter (SmartStart™ uses only the

SmartStart™ icon).

The parking lights will flash 3 times quickly

and remain lit. Release the button.

2. With the engine running, apply the parking

brake twice within 10 sec.

3. Make sure to release the brake pedal.

The parking lights will flash 3 times quickly

and remain lit.

4. Remove the key: the engine will keep on running.

5. Exit the vehicle. All doors should be closed, including the hood and trunk.

6. THERE ARE THREE POSSIBLE OPTIONS TO COMPLETE READY MODE (programmable

by installer)

OPTION 1: No lock OPTION 2: Manual shut down

(default) OPTION 3: Automatic shut

down

The engine stops. The engine keeps going until you

press either;

a. to lock the doors and shut

down the engine;

The engine runs for 8 sec.

then locks the doors before

finally shutting down the

engine, without user

P.10 User Guide

b. to unlock the doors and

shut down the engine;

c. to shut down the engine

without affecting the doors.

interaction.

WARNING: The vehicle is

not armed or locked down.

WARNING: Engine runs until the

pre-programmed run time

expires.

WARNING: Do not leave

your keys in the vehicle!

The Parking lights will flash

twice to indicate Ready

mode is set. To see the

icon, refresh the

remote screen by pressing

The icon will appear on your

screen.

The Parking lights will flash

twice to indicate Ready mode

is set. To see the icon,

refresh the remote screen by

pressing .

Remotestarting

1. Press the button for approximately 1 second and release.

2. The remote will beep once and the LCD will display “START”.

3. The remote will confirm the remote starter’s activation by beeping 3 times.

If your vehicle does not start on the first attempt, the system will shut down, wait a few seconds

and try to start the engine again. There will be 3 start attempts before the system gives up.

DrivingOff

With the vehicle running remotely, press the button to disarm the starter kill (if installed) and

unlock the doors. Enter the vehicle and do the following:

1. Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the CRANK

position while the engine is running. This would cause the starter motor to re-engage.)

2. Press the brake pedal to disengage the remote starter unit.

You are now ready to drive off.

Note: On some Push-To-Start (PTS) vehicles, no takeover is possible as pressing the brakes will

shut the engine down. Please talk to your technician to determine if the “Takeover mode” can be

set for your vehicle.

Arminganddisarmingthestarterkill(ifinstalled)

This added security feature will prevent the vehicle from starting with the Ignition key when the

starter kill is armed. If the system was installed with the starter kill option, the vehicle will not be

able to start with the key unless the system has been unlocked first or put into Valet Mode

(page 12).

Note: If the Starter Kill is installed, the vehicle will benefit from a protection against starter motor

damage that could occur after remote-starting the engine should the user, by force of habit, turn

the ignition key to the CRANK position.

The Starter Kill (if installed) can be configured by the installer either to Passive Mode (so as to arm

automatically) or Active Mode (so as to require the user’s intervention for arming). By default, the

Remote Car Starter is configured to Passive Mode.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Arranque remoto de Smart Start

Smart Start

Smart Start AS-1880FM Manual de usuario

Smart Start

Smart Start AS-2780U Manual de usuario

Smart Start

Smart Start AS2272 Manual de usuario

Smart Start

Smart Start ns1074 Manual de usuario

Smart Start

Smart Start GS-2260TW Manual de usuario

Smart Start

Smart Start TRANSMISSION REMOTE STARTER Manual de usuario

Smart Start

Smart Start BC-11 Manual de usuario

Manuales populares de Arranque remoto de otras marcas

AstroStart

AstroStart 803U Manual de usuario

Durite

Durite 0-649-20 Manual

EINHELL

EINHELL BT-PS 1000 Manual

Linear

Linear ACCESS AK-21 Especificaciones técnicas

Soundstream

Soundstream TARANTULA RS.2 Manual de usuario

Jaycar Electronics

Jaycar Electronics MB3752 Manual de usuario

Ultra Start

Ultra Start 72 Series Manual de usuario

ADS

ADS FLASHLOGIC FLRSVW1 Manual de usuario

Selecta

Selecta JS012 Manual de usuario

Black Widow Security

Black Widow Security BW RAS 400 Manual de usuario

Vector

Vector Power City DK080706 Suplemento

Code Alarm

Code Alarm CA-535 Manual de usuario

Ozito

Ozito OJS-800 Manual de usuario

Profi-Partner

Profi-Partner 46387 Manual de usuario

EZ STARTER

EZ STARTER EZ-45 Manual de usuario

Viper

Viper 4204 Manual de usuario

Essex Electronics

Essex Electronics KE-1701 Manual de usuario

EINHELL

EINHELL EGS 3600 Manual