Silver Cross 3D Pram System Manual de usuario

IMPORTANT: KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

silvercrossbaby.com

These instructions are important.

Read these instructions carefully before use

and keep them for future reference. Your

child’s safety may be affected if you do not

follow these instructions.

Your 3D Pram System is a high quality Silver

Cross product. It meets current British and

European safety standards and care and

regular light maintenance will ensure

long service.

This vehicle is intended for children from birth

and up to 15kg.

If somebody unfamiliar is using your 3D

always ensure that they read these instructions

carefully so that they understand how the

product works best.

The 3D Pram System is designed and tested

to accept the Ventura Plus Car Seat.

Always read all the instructions provided

carefully and remember, the safety of your

child is your responsibility.

Contents

First check all your parts have been supplied.

Your 3D Pram System includes:

1.1 3D Pram System body and chassis

1.2 Pram system liner

1.3 Hood

1.4 Apron

1.5 Footmuff

1.6 Raincover

1.3

1.1 1.2

1.4

1.5 1.6

Preparation for use

Remove all packaging material from your 3D

Pram System.

2.1 To unfold your 3D release the folding

lock by pulling up on each of the

handle catches (marked with a number

1) on both sides of the chassis

simultaneously.

2.2 Whilst holding each of the handle

catches (marked with a number 1), pull

upwards on the main handles. The

pushchair may lift off the ﬂoor during

this action.

2.3 As the 3D begins to unfold, release the

handle catches and immediately push

down with your foot on the centre of the

main lock to errect your pushchair.

2.4 Ensure that the secondary locks have

engaged on both sides, if not then

gently push down to engage them.

2.5 Your 3D is now erected. If you wish to

use your pushchair as a pram continue,

if you wish to use your 3D as a pushchair

proceed to point 4.1.

WARNING: Ensure that all

locking devices are engaged

before use.

2.1

2.2

2.3

2.4

2.5

silvercrossbaby.com

Using your 3D as a pram

3.1 Lift the leg supports to the upper

position, so that they touch the bumper

bar (see point 9.1).

3.2 Recline the seat to the lie ﬂat position by

releasing the mechanism at the back of

the seat.

3.3 Remove the head support by releasing

the zip and then releasing the harness

(see point 6.2). Feed the harness

through the harness button holes.

Using your 3D as a pram (cont.)

3.4 Flip the head support over so that it is

upside down and place over the buckle

so that the head support is now laying

in the ‘seat’ of the pushchair (under the

head of the pram liner)

3.5 Pull the fabrics over and under at the

handle end of the seat. Ensuring that the

recline mechanism can pass through the

opening in the liner.

3.6 Now pull the liner over the bumper bar,

and under the leg support. The liner will

attach with velcro underneath the leg

support.

3.1

3.2

3.3

3.4

3.5

3.6

silvercrossbaby.com

Using your 3D as a pram (cont.)

3.7 Now ﬁt your hood facing towards the

handles. The hood catches should easily

‘click’ onto the 3D. To lock, put the catch

down. Position the rear elasticated hood

skirt under the leg support joint.

3.8 Slip the apron cover over the bumper

bar end of the pram. Now slide the clips

on your apron on to the attachment

points inside the hood to enclose the

pram.

3.9 Your 3D Pram System is now ready for

use

WARNING: Do not add a

separate mattress.

Using your 3D as a pushchair

4.1 Attach your hood facing towards the

bumper bar. The hood catches should

easily ‘click’ into position. Lock them in

place by pushing the securing

catch down.

4.2 Select the position you require for the

seat back (see point 7.2) and the leg

support (see point 9.2).

Your 3D Pushchair is ready for use.

3.7

3.8

3.9

4.1

4.2

silvercrossbaby.com

Using the brake

5.1 To engage the brake, press down on

either pedal.

5.2 A ‘click’ will be heard.

Note: Always check that your brake

is fully engaged by gently rocking

the pushchair.

5.3 To disengage the brake, simply push the

brake pedal upwards, this will disengage

both sides simultaneously.

Using the harness

6.1 WARNING: Always use the

crotch strap in combination

with the waist belt.

To fasten the harness insert both buckle

clips into each side of the buckle.

Listen for the ‘click’.

6.2 WARNING: Use a harness

as soon as your child can sit

unaided.

To release the harness press the centre

and pull apart. The shoulder straps

can be unhooked from the buckle if

required.

6.3 Your harness is fully adjustable by

moving the slides (A), to make ﬁtting

easy. ‘D’ rings are provided for ﬁtting

a separate harness if required (B). Any

additional harness used must comply

with BS 6684. Your child should always

be harnessed in and should never be

left unattended, even for short periods

of time.

5.1

5.2

5.3

6.1

6.2

6.3

silvercrossbaby.com

Adjusting the seat position

7.1 Your 3D has 4 seat positions

7.2 To lower the seat, release the

mechanism on the rear top of the seat,

and gently lower to the desired position.

7.3 To raise the seat place your hand in the

middle of the rear of the seat and gently

lift to the desired position ensuring both

sides are level.

Operating your height

adjustable handles

8.1 The handles on your 3D have 2

positions. Press the button on the

underside and raise or lower to the

desired position.

Operating your leg support

9.1 Your 3D has a two position leg support

for your child.

9.2 Press the buttons simultaneously

underneath both sides of the leg

support and raise or lower to the

desired position.

7.1

7.2

7.3

8.1

9.2

9.1

silvercrossbaby.com

Operating the swivel wheels

10.1 Your 3D has lockable swivel wheels. By

pressing the locking catch down the

wheels will lock in the ﬁxed position. By

lifting this up the wheels will freely swivel

for easier steering.

You should always lock the wheels on

uneven surfaces, and before folding.

Using your hood

11.1 Your 3D hood ﬁts on the 3D facing both

directions, rearwards for the pram mode

and forwards for pushchair mode. Press

down on the hood arms to tension the

hood.

Using your liner

12.1 Your 3D liner has a Soft Wrap™ to

help provide your child with a safe and

comfortable position. Open the wrap

completely, place your child in the

centre of the Soft Wrap™ and close the

waist and crotch pads, securing with the

velcro tabs.

12.2 If you wish to attach a separate harness

D-rings can be accessed at the sides of

liner.

WARNING: Use a harness

as soon as your child can sit

unaided.

NOTE: Always use the

harness provided when in

pushchair mode

Your pram system liner can be washed

(please refer to washcare labels), it is

recommended that the mattress and

side supports are removed by accessing

from the base of the liner.

Using your raincover

13.1 To attach the raincover, ﬁrst slide over

the 3D Pram System handles and pass

over the hood. Then fasten the velcro

ﬂap at the rear.

13.2 Pull the raincover over the 3D at both

ends. Loop the velcro straps at the front

around the 3D leg, just below the foot

plate, and fasten. The raincover is now

ﬁtted.

13.3 Your 3D Pram System raincover is

designed to ﬁt the 3D in either pram or

pushchair mode. The raincover however

is not designed to ﬁt when the Ventura

Plus car seat is ﬁtted to the 3D. A

separate raincover can be purchased for

this purpose.

10.1

11.1

12.1

12.2

13.1

13.2

13.3

silvercrossbaby.com

Folding your 3D

Your 3D will fold with and without the

pram system liner ﬁtted. It is easier

without the liner in position, and we

would therefore recommend removing it

before folding.

Note: To ensure your 3D folds

correctly remove all items from the

shopping basket before attempting

to fold.

Note: If the liner is left in place and

folded for a long period, then the

foam mattress will curve upwards.

This will then regain its normal ﬂat

shape once a baby is placed in the

liner.

Note: If using as a travel system

please ensure that the Ventura Plus

car seat is removed before folding.

14.1 Before commencing the fold apply the

brake. Then lift the seat back into the

upright position (if in pram system make

sure you push the apron part upright)

lock the swivel wheels and ensure the

hood is fully folded back.

This is very important.

14.2 Next, gently Pull the 2 ﬁnger catches

simultaneously upwards (numbered 1)

until you hear the click and reveal the

red exclamation marks. Now press

down gently on the main pushchair

handles to disengage the main front

locks.

Folding your 3D

14.3 Rotate the red rotation lever (numbered

2) so it’s horizontal. Pull gently upwards

and the 3D will begin to fold. This lever

is not a carry handle.

Note: Do not force or over rotate

the red rotation lever, this may

cause damage to your pushchair.

14.4 Pushing on the handle and lifting the

red rotation lever will help your 3D to

fold easily.

14.5 Rock the pushchair onto the front wheels

and push downwards. Your 3D will lock

together.

14.6 From time to time it may be necessary

to lock your 3D by pressing the legs

together until the 3D locks. This is

perfectly normal.

NOTE: When folding your 3D in pram

mode, please ensure that the apron (seat

back) has been raised to the upright

position (see point 7.3), then proceed

with points 14.1 - 14.5.

NOTE: Silver Cross advises that the

apron is removed before folding in pram

mode.

14.1

14.2

14.3

14.4

14.5 14.6

Lock

silvercrossbaby.com

Unfolding your 3D

15.1 To unfold your 3D release the folding

lock by pulling up on each of the handle

catches (marked with a number 1) on

both sides of the chassis simultaneously.

15.2 Whilst holding each of the handle

catches (marked with a number 1), pull

upwards on the main handles. The

pushchair may lift off the ﬂoor during

this action.

15.3 As the 3D begins to unfold, release the

handle catches and immediately push

down with your foot on the centre of the

main lock to erect your pushchair.

NOTE: It is essential to ensure the

main lock is engaged. Failure to do

so could result in damage to your

pushchair.

Unfolding your 3D

15.4 Push the main pushchair handles

upwards to engage the secondary lock.

15.5 Check the secondary lock has engaged

on both sides. If not push down on the

tube to lock.

15.6 Your 3D is ready for use.

15.1

15.2

15.3

15.4

15.5

15.6

silvercrossbaby.com

Attaching your Ventura Plus

Car Seat

16.1 To attach your Ventura Plus, unfasten

the fabric cover on the 3D arms. Lift the

catches inside the arms until they reach

the stop point.

16.2 Position the Ventura Plus in the 3D seat,

do this by ﬁrstly positioning the large

opening on the Ventura Plus base over

the bumper bar.

16.3 Lock the handle down towards the

bumper bar, by pressing and holding

down both buttons simultaneously, then

rotating the handle. An audible ‘click’

will be heard. Your 3D Travel System is

now ready.

WARNING: Check that

the seat unit attachment

is correctly engaged by

checking both catches

are vertical and locked in

position with the car seat

Detaching your Ventura Plus

Car Seat

17.1 To detach your Ventura Plus,

simultaneously press the buttons on

both sides of the car seat handle at the

same time and hold down.

17. 2 Rotate the handle to the upright carry

position and lift the car seat out of the

3D.

17. 3 Push the car seat locks back into the 3D

arms and re-attach the fabrics back onto

the arms.

16.1

16.3

16.2

17.1

17. 2

17. 3

Otros manuales para 3D Pram System

Tabla de contenidos

Otros manuales de Paseante de Silver Cross

Silver Cross

Silver Cross Coast Manual de usuario

Silver Cross

Silver Cross Jet Manual de usuario

Silver Cross

Silver Cross Dune Manual de usuario

Silver Cross

Silver Cross Comet Manual de usuario

Silver Cross

Silver Cross Wayfarer Manual de usuario

Silver Cross

Silver Cross Sleepover Manual de usuario

Silver Cross

Silver Cross 2003 Kensington Manual de usuario

Silver Cross

Silver Cross Balmoral Manual de usuario

Silver Cross

Silver Cross Wayfarer Pushchair & Carrycot Manual de usuario

Silver Cross

Silver Cross SUN SAIL Manual de usuario

Silver Cross

Silver Cross Avia Manual de usuario

Silver Cross

Silver Cross Pacific Manual de usuario

Silver Cross

Silver Cross REEF Manual de usuario

Silver Cross

Silver Cross 3D Pram System Manual de usuario

Silver Cross

Silver Cross Freeway Manual de usuario

Silver Cross

Silver Cross ZEST Manual de usuario

Silver Cross

Silver Cross Pioneer Manual de usuario

Silver Cross

Silver Cross Wave Manual de usuario

Silver Cross

Silver Cross Coast Manual de usuario

Silver Cross

Silver Cross Wing 2 Manual de usuario

Silver Cross

Silver Cross Kensington Manual de usuario

Silver Cross

Silver Cross Tide Manual de usuario

Silver Cross

Silver Cross Jet Manual de usuario

Silver Cross

Silver Cross Coast Manual de usuario

Manuales populares de Paseante de otras marcas

Hauck

Hauck Priya Trioset Manual de usuario

CHILDHOME

CHILDHOME CWQDN Manual de usuario

Dreamer Design

Dreamer Design Rebound GST Manual de usuario

Britax

Britax STEELCRAFT AGILE Manual de usuario

Graco

Graco 7427 Manual de usuario

Comfort

Comfort COMPASS Manual de usuario

OBaby

OBaby Aura Manual de usuario

Tutek

Tutek Tirso Manual de usuario

Babify

Babify Dual Plus Manual de usuario

Graco

Graco Stroller Manual de usuario

Special Tomato

Special Tomato Jogger Manual de usuario

Chicco

Chicco CORTINA TOGETHER TWO-PASSENGER STROLLER Manual de usuario

Otto Bock

Otto Bock Kimba neo Manual de usuario

Milly Mally

Milly Mally ROYAL Guía de inicio rápido

Hauck

Hauck DUETT 3 PRAM Manual de usuario

BOB

BOB DUALLIE Manual de usuario

Nuna

Nuna Pepp Manual de usuario

Britax

Britax B2 Manual de usuario