Silicon Laboratories Si5397 Series Manual de usuario

UG353: Si5397 Evaluation Board User's

Guide

The Si5397-EVB is used for evaluating the Si5397 Any-Frequency, Any-Output, Jitter-

Attenuating Clock Any-Frequency, Any-Output, Jitter-Attenuating Clock Multiplier Revi-

sion A. The device grade and revision is distinguished by a white 1 inch x 0.187 inch

label installed in the lower left hand corner of the board. In the example below, the label

"SI5397A-A-EB" indicates the evaluation board has been assembled with an Si5397 de-

vice, Grade A,Revision A, installed. (For ordering purposes only, the terms “EB” and

“EVB” refer to the board and the kit, respectively. For the purpose of this document, the

terms are synonymous in context.)

KEY FEATURES

• Powered from USB port or external +5 V

power supply via screw terminals

•Onboard 48 MHz XTAL allows standalone

or holdover mode of operation on the

Si5397

• CBPro™ GUI programmable VDD supply

allows device supply voltages of 3.3, 2.5,

or 1.8 V

• CBPro GUI programmable VDDO supplies

allow each of the eight outputs to have its

own supply voltage selectable from 3.3,

2.5, or 1.8 V

• CBPro GUI allows control and

measurement of voltage, current, and

power of VDD and all eight VDDO supplies

• Status LEDs for power supplies and

control/status signals of the Si5397

• SMA connectors for input clocks, output

clocks and optional external timing

reference clock

silabs.com | Building a more connected world. Rev. 0.1

1. Functional Block Diagram

Below is a functional block diagram of the Si5397-A-EB. This evaluation board can be connected to a PC via the main USB connector

for programming, control, and monitoring. See 3. Quick Start or 10.3 Overview of ClockBuilderPro Applications for more information.

Si5397

Output

Termination

CLKOUT_1

CLKOUT_1B

Output

Termination

CLKOUT_2

CLKOUT_2B

Output

Termination

CLKOUT_3

CLKOUT_3B

Output

Termination

CLKOUT_4

CLKOUT_4B

Output

Termination

CLKOUT_5

CLKOUT_5B

Output

Termination

CLKOUT_6

CLKOUT_6B

Output

Termination

Output

Termination

XAXB

Crystal / Term

Input

Termination

Input

Termination

Input

Termination

CLKIN_0

CLKIN_0B

CLKIN_1

CLKIN_1B

CLKIN_2

CLKIN_2B

Power Supply

C8051F380

MCU

Peripherals

I2C/SPI Bus

VDDO_0

VDD_Core

VDD_3.3

VDDO_1

VDDO_2

VDDO_3

VDDO_4

VDDO_5

VDDO_6

VDDO_7

VDDO_0

VDD_Core

VDD_3.3

VDDO_1

VDDO_2

VDDO_3

VDDO_4

VDDO_5

VDDO_6

VDDO_7

Main USB

Connector

Aux USB

Connector

Ext +5V

Connector

I2C/SPI Bus

+5V_USB

+5V_Aux

+5V_Ext

VDDMCU

Input Clock 0 {

Input Clock 1 {

Input Clock 2 {

}Output Clock 0

}Output Clock 1

}Output Clock 2

}Output Clock 3

}Output Clock 4

}Output Clock 5

}Output Clock 6

}Output Clock 7

Power only

Control/

Status

INTR

Alarm_Status

Input

Termination

CLKIN_3

CLKIN_3B

Input Clock 3 {

CLKOUT_0

CLKOUT_0B

CLKOUT_7

CLKOUT_7B

Optional External

XAXB Ref Input {

Figure 1.1. Si5397-A-EB Functional Block Diagram

UG353: Si5397 Evaluation Board User's Guide

Functional Block Diagram

silabs.com | Building a more connected world. Rev. 0.1 | 2

2. Si5397-A-EVB Support Documentation and ClockBuilderPro™ Software

All Si5397-A-EVB schematics, BOMs, User’s Guides, and software can be found online at: http://www.silabs.com/products/clocksoscil-

lators/pages/si539x-evb.aspx.

UG353: Si5397 Evaluation Board User's Guide

Si5397-A-EVB Support Documentation and ClockBuilderPro™ Software

silabs.com | Building a more connected world. Rev. 0.1 | 3

3. Quick Start

1. Install the ClockBuilderPro desktop software from http://www.silabs.com/CBPro.

2. Connect a USB cable from the Si5397-A-EB to the PC where the software was installed.

3. Leave the jumpers as installed from the factory, and launch the ClockBuilderPro software.

4. You can use ClockBuilderPro to create, download, and run a frequency plan on the Si5397-A-EB.

5. For the Si5397 data sheet, go to http://www.silabs.com/timing.

UG353: Si5397 Evaluation Board User's Guide

Quick Start

silabs.com | Building a more connected world. Rev. 0.1 | 4

4. Jumper Defaults

Table 4.1. Si5397-EB Jumper Defaults1

Location Type I= Installed

0 = Open Location Type I = Installed

0 = Open

JP1 2-pin I JP23 2-pin O

JP2 2-pin O JP24 2-pin O

JP3 2-pin I JP25 2-pin O

JP4 2-pin I JP26 2-pin O

JP5 2-pin O JP27 2-pin O

JP6 2-pin O JP28 2-pin O

JP7 2-pin I JP29 2-pin O

JP8 2-pin O JP30 2-pin O

JP9 2-pin O JP31 2-pin O

JP10 2-pin I JP32 2-pin O

JP13 2-pin O JP33 2-pin O

JP14 2-pin I JP34 2-pin O

JP15 3-pin all open JP35 2-pin O

JP16 3-pin 1 to 2 JP36 2-pin O

JP17 2-pin O JP38 3-pin All Open

JP18 2-pin O JP39 2-pin O

JP19 2-pin O JP40 2-pin I

JP20 2-pin O JP41 2-pin I

JP21 2-pin O J36 5 x 2 Hdr All 5 installed

JP22 2-pin O

Note:

1. Refer to the Si5397-A-EB schematics for the functionality associated with each jumper.

UG353: Si5397 Evaluation Board User's Guide

Jumper Defaults

silabs.com | Building a more connected world. Rev. 0.1 | 5

5. Status LEDs

Location Silkscreen Color Status Function Indication

D27 5VUSBMAIN Blue Main USB +5 V present

D22 3P3V Blue DUT +3.3 V is present

D26 VDD DUT Blue DUT VDD voltage present

D25 INTR Red MCU INTR (Interrupt) active

D21 READY Green MCU Ready

D24 BUSY Green MCU Busy

D2 LOS_XAXB_B Blue Loss of Signal at XAXB input

D5 LOL_AB Blue Lossof Lock - DSPLL A

D6 LOL_BB Blue Lossof Lock - DSPLL B

D8 LOL_CB Blue Lossof Lock - DSPLL C

D11 INTRB Blue Si5397 Interrupt Active

D12 LOL_DB Blue Loss of Lock _ DSPLL D

D27, D22, and D26 are illuminated when USB +5 V, Si5397 +3.3 V, and Si5397 Vcore supply voltages, respectively, are present. D25,

D21, and D24 are status LEDs showing onboard MCU activity. D2 indicates loss of signal at XAXB input (either crystal osc or external

reference). D5, D6, D8, D12 indicate loss of lock for one of four internal DSPLLs (A–D). D11 indicates the Si5397 interrupt output is

active (as configured by Si5397 register programming). LED locations are highlighted below with LED function name indicated on board

silkscreen.

Figure 5.1. Status LEDs

UG353: Si5397 Evaluation Board User's Guide

Status LEDs

silabs.com | Building a more connected world. Rev. 0.1 | 6

6. External Reference Input (XA/XB)

An external timing reference (48 MHz XTAL) is used in combination with the internal oscillator to produce an ultra-low jitter reference

clock for the DSPLL and for providing a stable reference for the free-run and holdover modes.The Si5397-A-EB can also accommodate

an external reference clock instead of a crystal.To evaluate the device with an external REFCLK, C111 and C113 must be populated

and XTAL Y1 removed (see figure below). The REFCLK can then be applied to SMA connectors J39 and J40.

Figure 6.1. External Reference Input Circuit

UG353: Si5397 Evaluation Board User's Guide

External Reference Input (XA/XB)

silabs.com | Building a more connected world. Rev. 0.1 | 7

7. Clock Input Circuits (INx/INxB)

The Si5397-A-EB has eight SMA connectors (IN0, IN0B–IN3, IN3B) for receiving external clock signals. All input clocks are terminated

as shown below. Note that input clocks are ac-coupled and 50 Ω terminated. This represents four differential input clock pairs. Single-

ended clocks can be used by appropriately driving one side of the differential pair with a single-ended clock. For details on how to con-

figure inputs as single-ended, please refer to the Si5397 data sheet.

Figure 7.1. Input Clock Termination Circuit

UG353: Si5397 Evaluation Board User's Guide

Clock Input Circuits (INx/INxB)

silabs.com | Building a more connected world. Rev. 0.1 | 8

8. Clock Output Circuits (OUTx/OUTxB)

Each of the sixteen output drivers (eight differential pairs, OUT0/OUT0B—OUT7/OUT7B) is ac-coupled to its respective SMA connec-

tor. The output clock termination circuit is shown below. The output signal will have no dc bias. If dc coupling is required, the ac cou-

pling capacitors can be replaced with a resistor of appropriate value. The Si5397-A-EB provides pads for optional output termination

resistors and/or low-frequency capacitors. Note that components with a schematic “NI” designation are not normally populated on the

Si5397-A-EB and provide locations on the PCB for optional dc/ac terminations by the end user.

Figure 8.1. Output Clock Termination Circuit

UG353: Si5397 Evaluation Board User's Guide

Clock Output Circuits (OUTx/OUTxB)

silabs.com | Building a more connected world. Rev. 0.1 | 9

9. Installing ClockBuilderPro (CBPro) Desktop Software

To install the CBOPro software on any Windows 7 (or above) PC, go to http://www.silabs.com/CBPro and download the ClockBuilder-

Pro software.

Installation instructions and User’s Guide for ClockBuilderPro can be found at the download link shown above.

UG353: Si5397 Evaluation Board User's Guide

Installing ClockBuilderPro (CBPro) Desktop Software

silabs.com | Building a more connected world. Rev. 0.1 | 10

Otros manuales para Si5397 Series

Tabla de contenidos

Otros manuales de Placa madre de Silicon Laboratories

Silicon Laboratories

Silicon Laboratories Si5310-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories CP2201EK Manual de usuario

Silicon Laboratories

Silicon Laboratories Wizard Gecko WGM110 Wi-Fi Wireless Starter... Instrucciones de funcionamiento y mantenimiento

Silicon Laboratories

Silicon Laboratories CP2130 Manual de usuario

Silicon Laboratories

Silicon Laboratories CP2105 Manual de usuario

Silicon Laboratories

Silicon Laboratories Sensor-EXP-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories SENSOR PUCK Manual de usuario

Silicon Laboratories

Silicon Laboratories Si1120-EK Manual de usuario

Silicon Laboratories

Silicon Laboratories CP2112-EK Manual de usuario

Silicon Laboratories

Silicon Laboratories M88 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si827 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories BRD4175A Manual de usuario

Silicon Laboratories

Silicon Laboratories Si52147 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si50x-FPB1-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories CP2110 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5341-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5338-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si890x-PWR-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5372 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si51211 EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories UG524 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si4700 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si53112 Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F960 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario