Silicon Laboratories Si5341-EVB Manual de usuario

Si5341-EVB

Si5341 EVALUATION BOARD USER’SGUIDE

Description

The Si5341-EVB is used for evaluating the Si5341 Low

Jitter Any-Frequency Clock Generator. The Si5341 uses

the patented Multisynthtechnology to generate up to

10 independent clock frequencies each with 0 ppm

synthesis error. The Si5341-EVB has 3 independent

input clocks, an optional feedback input clock for zero

delay mode, and 10 independent output clocks. The

Si5341-EVB can be controlled and configured using the

Clock Builder Pro(CB Pro) software tool.

EVB Features

Powered from USB port or external power supply.

Onboard 48 MHz XTAL allows free-run mode of

operation on the Si5341 or up to 3 input clocks for

synchronous clocking.

Feedback clock input for optional zero delay mode.

CBProGUI programmable VDD supply allows

device to operate from 3.3, 2.5, or 1.8 V.

CBPro GUI programmable VDDO supplies allow each

of the 10 outputs to have its own power supply

voltage selectable from 3.3, 2.5, or 1.8 V.

CBPro GUI-controlled voltage, current, and power

measurements of VDD and all VDDO supplies.

Status LEDs for power supplies and control/status

signals of Si5341.

SMA connectors for input and output clocks.

Figure 1. Si5341 Evaluation Board

Si5341-EVB

2 Rev. 1.1

1. Functional Block Diagram

Below is a functional block diagram of the Si5341-EVB. This EVB can be connected to a PC via the main USB

connector for programming, control, and monitoring. See section “3. Quick Start” or section “8. Installing

ClockBuilderPro (CBPro) Desktop Software” for more information.

Figure 2. Si5341-EVB Functional Block Diagram

Si5341-EVB

Rev. 1.1 3

2. Si5341-EVB Support Documentation and ClockBuilderProSoftware

All Si5341 schematics, BOMs, User’s Guides, and software can be found online at the following link:

http://www.silabs.com/products/clocksoscillators/pages/si538x-4x-evb.aspx

3. Quick Start

1. Install ClockBuilderPro desktop software from http://www.silabs.com/CBPro.

2. Connect a USB cable from Si5341-EVB to the PC where the software was installed.

3. Leave the jumpers as installed from the factory, and launch the ClockBuilderPro software.

4. You can use ClockBuilderPro to create, download, and run a frequency plan on the Si5341-EVB.

5. For the Si5341 data sheet, go to http://www.silabs.com/timing.

4. Jumper Defaults

Refer to the Si5341 EVB schematics for the functionality associated with each jumper.

Si5341 EVB Jumper Defaults

Location Type I = Installed

0 = Open Location Type I = Installed

0 = Open

JP1 2pin O JP23 2pin O

JP2 2pin I JP24 2pin O

JP3 2pin O JP25 2pin O

JP4 2pin I JP26 2pin O

JP5 2pin I JP27 2pin O

JP6 2pin I JP28 2pin O

JP7 2pin I JP29 2pin O

JP8 2pin I JP30 2pin O

JP9 2pin O JP31 2pin O

JP10 2pin I JP32 2pin O

JP13 2pin O JP33 2pin O

JP14 2pin I JP34 2pin O

JP15 3pin 1to2JP35 2pin O

JP16 3pin 1to2JP36 2pin O

JP17 2pin O JP38 3pin allopen

JP18 2pin O JP39 2pin O

JP19 2pin O JP40 2pin O

JP20 2pin O JP41 2pin O

JP21 2pin O

JP22 2pin O J36 5x2Hdr All5installed

Si5341-EVB

4 Rev. 1.1

5. Status LEDs

D27, D22, and D26 are illuminated when USB +5 V, Si5341 +3.3 V, and Si5341 VDD supply voltages, respectively,

are present. D25, D21, and D24 are status LEDs showing on-board MCU activity.

Figure 3. Status LEDs

Si5341EVBStatusLEDs

Location Silkscreen Color StatusFunctionIndication

D27 5VUSBMAIN Blue Main USB +5V present

D22 3P3V Blue DUT +3.3 V is present

D26 VDD DUT Blue DUT VDD voltage present

D25 INTR Red MCU INTR (Interrupt) active

D21 READY Green MCU Ready

D24 BUSY Green MCU Busy

Si5341-EVB

Rev. 1.1 5

6. Clock Input Circuits (INx/INxB and FB_IN/FB_INB)

The Si5341-EVB has eight SMA connectors (IN0/IN0B–IN2/IN3B and FB_IN/FB_INB) for receiving external clock

signals. All input clocks are terminated as shown in Figure 4 below. Note input clocks are AC coupled and 50 ohm

terminated. This represents 4 differential input clock pairs. Single-ended clocks can be used by appropriately

driving one side of the differential pair with a single-ended clock. For details on how to configure inputs as

single-ended, please refer to the Si5341 data sheet.

Figure 4. Input Clock Termination Circuit

7. Clock Output Circuits (OUTx/OUTxB)

Each of the twenty output drivers (10 differential pairs) is AC coupled to its respective SMA connector. The output

clock termination circuit is shown in Figure 5 below. The output signal will have no dc bias. If DC coupling is

required, the AC coupling capacitors can be replaced with a resistor of appropriate value. The Si5341-EVB

provides pads for optional output termination resistors and/or low frequency capacitors. Note that components with

schematic “NI” designation are not normally populated on the Si5341-EVB and provide locations on the PCB for

optional DC/AC terminations by the end user.

Figure 5. Output Clock Termination Circuit

Si5341-EVB

6 Rev. 1.1

8. Installing ClockBuilderPro (CBPro) Desktop Software

To install the CBOPro software on any Windows 7 (or above) PC:

Go to http://www.silabs.com/CBPro and download ClockBuilderPro software.

Installation instructions and User’s Guide for ClockBuilderPro can be found at the download link shown above.

Please follow the instructions as indicated.

9. Using the Si5341 EVB

9.1. Connecting the EVB to Your Host PC

Once ClockBuilderPro software is installed, connect to the EVB with a USB cable as shown below.

Figure 6. EVB Connection Diagram

Si5341-EVB

Rev. 1.1 7

9.2. Additional Power Supplies

Although additional power (besides the power supplied by the host PC’s USB port) is not needed for most

configurations, two additional +5 VDC power supplies (MAIN and AUX) can be connected to J33 and J34 (located

on the bottom of the board, near the USB connector). Refer to the Si5341-EVB schematic for details.

The Si5341-EB comes preconfigured with jumpers installed at JP15 and JP16 (pins 1-2 in both cases) in order to

select “USB”. These jumpers, together with the components installed, configure the evaluation board to obtain all

+5 V power solely through the main USB connector at J37. This setup is the default configuration and should

normally be sufficient.

Figure 7 shows the correct installation of the jumper shunts at JP15 and JP16 for default or standard operation.

Figure 7. JP15-JP16 Standard Jumper Shunt Installation

Errata Note:Some early versions of the 64-pin Si534x-EVBs may have the silkscreen text at JP15-JP16 reversed regarding

EXT and USB, i.e., USB EXT instead of EXT USB. Regardless, the correct installation of the jumper shunts for

default or standard operation is on the right hand side as read and viewed in Figure 7.

The general guidelines for single USB power supply operation are listed below:

Use either a USB 3.0 or USB 2.0 port. These ports are specified to supply 900 mA and 500 mA

respectively at +5 V.

If you are working with a USB 2.0 port and you are current limited, turn off enough DUT output voltage

regulators to drop the total DUT current ≤470 mA. (Note: USB 2.0 ports may supply > 500 mA. Provided

the nominal +5 V drops gracefully by less than 10%, the EVB will still work.)

If you are working with a USB 2.0 and you are current limited and need all output clock drivers enabled,

re-configure the EVB to drive the DUT output voltage regulators from an external +5 V power supply as

follows:

Connect external +5 V power supply to terminal block J33 on the back side of the PCB.

Move the jumper at JP15 from pins 1-2 USB to pins 2-3 EXT.

Si5341-EVB

8 Rev. 1.1

9.3. Overview of ClockBuilderPro Applications

The ClockBuilderPro installer will install two main applications:

Figure 8. Application #1: ClockbuilderPro Wizard

Use the CBPro Wizard to:

Create a new design

Review or edit an existing design

Export: create in-system programming

Figure 9. Application #2: EVB GUI

Use the EVB GUI to:

Download configuration to EVB’s DUT (Si5341)

Control the EVB’s regulators

Monitor voltage, current, power on the EVB

Si5341-EVB

Rev. 1.1 9

9.4. Common ClockBuilderPro Work Flow Scenarios

There are three common workflow scenarios when using CBPro and the Si5341 EVB. These workflow scenarios

are:

Workflow Scenario #1: Testing a Silicon Labs-Created Default Configuration

Workflow Scenario #2: Modifying the Default Silicon Labs-Created Device Configuration

Workflow Scenario #3: Testing a User-Created Device Configuration

Each is described in more detail in the following sections.

9.5. Workflow Scenario #1: Testing a Silicon Labs-Created Default Configuration

The flow for using the EVB GUI to initialize and control a device on the EVB is as follows.

Once the PC and EVB are connected, launch ClockBuilder Pro by clicking on this icon on your PC’s desktop.

Figure 10. ClockBuilderPro Desktop Icon

If an EVB is detected, click on the “Open Default Plan” button on the Wizard’s main menu. CBPro automatically

detects the EVB and device type.

Figure 11. Open Default Plan

Once you open the default plan (based on your EVB model number), a popup will appear.

Figure 12. Write Design to EVB Dialog

Select “Yes” to write the default plan to the Si5341 device mounted on your EVB. This ensures the device is

completely reconfigured per the Silicon Labs default plan for the DUT type mounted on the EVB.

Si5341-EVB

10 Rev. 1.1

Figure 13. Writing Design Status

After CBPro writes the default plan to the EVB, click on “Open EVB GUI” as shown below.

Figure 14. Open EVB GUI

The EVB GUI will appear. Note all power supplies will be set to the values defined in the device’s default CBPro

project file created by Silicon Labs, as shown below.

Figure 15. EVB GUI Window

Tabla de contenidos

Otros manuales de Placa madre de Silicon Laboratories

Silicon Laboratories

Silicon Laboratories Thunderboard EFM32GG12 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si8284-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5338 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5338 Manual de usuario

Silicon Laboratories

Silicon Laboratories SLWRB4179B Manual de usuario

Silicon Laboratories

Silicon Laboratories Si4827-DEMO Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5356-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si890x-PWR-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories SENSOR PUCK Manual de usuario

Silicon Laboratories

Silicon Laboratories Si2493/57/34/15/04-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories EZRadioPRO F912/4431 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5350/51-B20QFN-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si514 Manual de usuario

Silicon Laboratories

Silicon Laboratories IRSLIDER2EK Si1142 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5345-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si4700 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si827 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories Si84xxISO Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5 UC-EVB Series Manual de usuario

Silicon Laboratories

Silicon Laboratories Thunderboard EFR32BG22 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si8600ISO Manual de usuario

Silicon Laboratories

Silicon Laboratories CP2104 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si4844-B Series Manual de usuario

Silicon Laboratories

Silicon Laboratories Si1120-EK Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario