Silicon Laboratories Sensor-EXP-EVB Manual de usuario

Sensor EXP EVB UG

Sensor EXP Evaluation Board USER’SGUIDE

1. Introduction

This Sensor-EXP-EVB is a hardware plugin card for the EFM32 starter kits (STKs). It contains the Si7013 humidity

and temperature sensor as well as the Si1147 UV and proximity sensor. A weather station software demo is

available to download to the Zero or Tiny Gecko STK through simplicity studio. When downloaded to the

EFM32ZG-STK3200 Zero Gecko STK or the EFM32TG-STK3300 Tiny Gecko STK, the demo displays humidity,

temperature, and UV index and performs gesture detection. Right or left gestures move the display type and, on

the temperature screen, up or down gestures move the display between °C or °F.

1.1. Features

Si7013 Humidity and Temperature sensor

Si1147 proximity sensor

3 IR LEDs for gesture detection

20-pin expansion header

Battery operation with long battery life

1.2. Getting Started

The first step to get started with your new Sensor-EXP-EVB is to go to www.silabs.com/simplicity-studio.

The simplicity studio software package contains all the tools, drivers, software examples and documentation

needed to use the Sensor-EXP-EVB.

You will need to connect the Sensor-EXP-EVB to the EFM32ZG-STK3200 Zero Gecko STK or the EFM32TG-

STK3300 Tiny Gecko STK. The demo code can be loaded using the USB cable and J-Link debug interface.

Sensor EXP EVB UG

2 Rev. 0.2

2. Weather Station Demo

2.1. Loading the Demo

Connect the USB cable to the STK and launch Simplicity Studio. Click on “Detect connected device” then click on

the Demos button (top right) and select the Sensor-EXP weather station demo from the list. Make sure the Bat/Dbg

switch on the STK is set to DBG and click Start to download the demo. The following figures show the Zero Gecko

STK screens.

Figure 1. Simplicity Studio

Sensor EXP EVB UG

Rev. 0.2 3

Figure 2. Device Detection



Sensor EXP EVB UG

4 Rev. 0.2

Figure 3. Select Demos

Sensor EXP EVB UG

Rev. 0.2 5

Figure 4. Demo Selection



Sensor EXP EVB UG

6 Rev. 0.2

2.2. Using the Demo

After download, the USB cable can be disconnected and the demo will run from battery power by switching the

Bat/Dbg switch to battery.

The demonstration will first show a start screen with some basic instructions. In order to conserve power the

demonstration code wakes up every few seconds and looks for a proximity event before looking for gestures. To

initiate a proximity event, hold your hand (with fingers closed) over the Sensor-EXP-EVB. Once the proximity event

has been detected, gesture detection is enabled. The gesture control state is fairly high-power compared to the idle

state, so the code will automatically terminate gesture detection after one minute of inactivity. Swiping your hand

across the Sensor-EXP-EVB in left and right motions will change the display as shown in Figure 5.

Figure 5. Displays

While on the temperature display, an up or down swipe motion will change the units to °C or °F.

Humidity

(Si7013) UV Index

(Si1147)

Temperature

(Si7013)

Sensor EXP EVB UG

Rev. 0.2 7

3. Block Diagram

Figure 6. Sensor EXP Component Layout

Battery to

converter

JP3

I2C

INTERFACE

All other lines

VMCU

(Battery)

JP4

Si1147 UV

and

Proximity

sensor

Si7013

Humidity and

Temperature

sensor

LEDs

Sensor EXP EVB UG

8 Rev. 0.2

4. EXP Hardware Layout

4.1. Sensor-EXP-Evaluation Board

Figure 7. Assembled Demo Platform

Si1147 UV and proximity

sensor

Si7013 Humidity and

Temperature sensor

IR LEDs I2C ribbon connector

EXP connector for EFM32 STK

Sensor EXP EVB UG

Rev. 0.2 9

4.2. Sensor-EXP-EVB Connected to Zero Gecko STK

Figure 8. Sensor-EXP-EVB Connected to Zero Gecko STK

Hover hand to create a proximity event (Figure 9).

Figure 9. Hover Gesture

Swipe hand right or left to change display (Figure 10). Swipe up and down to change temperature display units.

Figure 10. Left/Right Swipe Gesture

Sensor EXP EVB UG

10 Rev. 0.2

5. Connectors

On the left hand side of the board there is a right-angle 20-pin expansion header is to allow connection to the

EFM32 STK board. This connector is not currently compatible with Wonder, Giant, or Leopard Gecko STKs.

However, with hardware modifications, the sensor-EXP-EVB can be used with these STKs as well. On the right

hand side of the board there is another connector to allow connection to another plugin card. J6 is a flat ribbon

cable connector to connect other devices such as additional sensors to the I2C bus.

6. Schematics, Assembly Drawings and BOM

The schematics, assembly drawings and bill of materials (BOM) for the Sensor-EXP-EVB are available through

simplicity studio when the EXP documentation package has been installed.

Otros manuales para Sensor-EXP-EVB

Tabla de contenidos

Otros manuales de Placa madre de Silicon Laboratories

Silicon Laboratories

Silicon Laboratories Si5341-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Biometric-EXP EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5347-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5-EVB Series Manual de usuario

Silicon Laboratories

Silicon Laboratories SLWRB4173A Manual de usuario

Silicon Laboratories

Silicon Laboratories CP2201EK Manual de usuario

Silicon Laboratories

Silicon Laboratories Si57-EVB Series Manual de usuario

Silicon Laboratories

Silicon Laboratories UG524 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si1102EK Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F850 BLDC Manual de usuario

Silicon Laboratories

Silicon Laboratories Sensor-EXP-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si1120 Manual de usuario

Silicon Laboratories

Silicon Laboratories CP2105 Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F2 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories Si827 Series Manual de usuario

Silicon Laboratories

Silicon Laboratories AMW007 Manual de usuario

Silicon Laboratories

Silicon Laboratories SiTCXO1-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories EFM8LB1-SLSTK2030A Manual de usuario

Silicon Laboratories

Silicon Laboratories Si47xx-EVB Series Manual de usuario

Silicon Laboratories

Silicon Laboratories Si823Hx-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5345-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si53108-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories EFR32xG22 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5317-EVB Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario