SIIG Low Profile USB Adapter Manual de usuario
1
Low Profile USB Adapter
Quick Installation Guide
04-0192A
Introducing the Low Profile USB Adapter
The Low Profile USB Adapter conforms to the new PCI card form factor
standard made for space constrained system designs. It is a
high-speed Universal Serial Bus (USB) host adapter that has more
user-friendly features than the current I/O interfaces such as serial/
parallel ports. It works with all types of USB devices including digital
cameras, PC video cameras, scanners, joysticks and more.
Features and Benefits
• Compliant to USB Specification, Version 1.1
• Completely implements OpenHCI Specification, Version 1.0a
• Compliant to PCI Specification, Version 2.1
• Fully compatible with Windows Standard OHCI drivers
• User friendly plug-n-play and hot-swapping features allow
you to attach/remove USB devices without turning your
system off
• Provides 2 downstream ports for USB device connections
• Supports both 12 Mbps and 1.5 Mbps data transfer modes
Dimensions:
• PCB: 119.91 mm (L) x 64.41 mm (H)
• Bracket: 18.42 mm (W) x 79.20 mm (H)
System Requirements
• Pentium or equivalent computer with one available PCI slot
• Windows 98/98 SE/ME/2000
Package Contents
• One Low Profile USB Adapter
• One 5-year warranty card
• This quick installation guide
2
Hardware Installation
General instructions for installing the card are provided below, since
the design of computer cases and motherboards vary. Refer to your
computer’s reference manual for further information, if needed.
Static Electricity Discharge may permanently damage your system.
Discharge any static electricity build up in your body by touching
your computer’s case for a few seconds. Avoid any contact with
internal parts and handle cards only by their external edges.
1. Turn OFF the power to your computer and any other connected
peripheral devices. Unplug the computer's power cord.
2. Remove your computer’s cover and install the card in an
available PCI slot.
3. Push the board down firmly, but gently, until it is well seated.
4. Secure the card and replace the cover.
Software Installation
Windows 98/98 SE:
Windows 98/98 SE will automatically detect the presence of the
Low Profile USB Adapter. Follow the procedures below to install the
host adapter drivers:
1. At the Add New Hardware Wizard, click Next.
2. Choose Search for the best driver for your device
(Recommended) and click Next.
3. Insert Windows 98 CD-ROM and check CD-ROM check box.
4. Click Next, Next, and Finish to complete driver installation.
Windows ME/2000:
Windows ME and Windows 2000 will automatically detect and
install the correct driver for this adapter. No installation is needed.
3
Technical Support
QUESTIONS? SIIG’s Online Support has the answers! Simply
visitourwebsiteatwww.siig.com andclickonONLINE SUPPORT.
Our online support database is updated daily with new drivers
and solutions. The answers to your problems could be just a few
clicks away.
Return Merchandise Authorization (RMA)
SIIGwarrants to theoriginal buyer ofthe product thatthe hardware
is free of defects in materials and workmanship for a period of one,
two or five years from the date of purchase. If your product fails to
be in good working order during the warranty period, you may
return it to SIIG for repair or replacement at SIIG's option.
To return the product, you need to follow these steps.
Step 1: Contact SIIG's RMA Department
Toobtain an RMAnumber, SIIG's RMADepartment can bereached
by phone at (510)413-5333 or fax at (510)657-5962 or email at
serial number is required. This number can be found on the side of
the box and on the back of the product.
Step 2: Complete the RMA form
• Fill out your Return Merchandise Authorization (RMA) form, and
include it in the package with the product.
• Properly pack the product for shipping. All software, cable(s) and
other accessories that came with the original package must be
included.
• ClearlywriteyourRMAnumberonthetopofthereturnedpackage
and on the accompanying RMA form.
SIIG will refuse to accept any shipping package, and will not
beresponsibleforaproduct returned without an RMA number
posted on the outside of the shipping carton.
Step 3: Ship the Product
You are responsible for the cost of shipping back to SIIG at the
following address:
SIIG, Inc. RMA#_______________
6078 Stewart Ave.
Fremont, CA 94538
SIIG will ship the repaired or replaced product via UPS Ground or
US Mail at no cost to you.
PRODUCT NAME MODEL NUMBER
Low Profile USB Adapter LP0402
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC NOTICE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio and
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio or TV technician for help
Caution:
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
this equipment
THE PARTY RESPONSIBLE FOR
PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152
Low Profile USB Adapter is a trademark of SIIG, Inc.
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft, Windows and Windows
NT are registered trademarks of Microsoft Corporation. Pentium is a registered trademark of
Intel Corporation. Other names used in publication are for identification only and may be
trademarks of their respective companies.
November, 2000 Copyright ©2000 by SIIG, Inc. All rights reserved.
Tabla de contenidos
Otros manuales de Hardware de computadora de SIIG
SIIG
SIIG Cyber PCI I/O Manual de usuario
SIIG
SIIG JU-P40412-S1 Manual de usuario
SIIG
SIIG NN-PC8312-S2 Manual de usuario
SIIG
SIIG SC-SAE612-S1 Manual de usuario
SIIG
SIIG DP FireWire 800 3-Port PCIe Manual de usuario
SIIG
SIIG FireWire Dual-Port CardBus Manual de usuario
SIIG
SIIG CyberParallel Dual Manual de usuario
SIIG
SIIG Parallel Pro Manual de usuario
SIIG
SIIG SC-SAE512-S1 Manual de usuario
SIIG
SIIG PCIe to ExpressCard Bay Manual de usuario
SIIG
SIIG SATA II PCIe RAID Manual de usuario
SIIG
SIIG ExpressCard 11-in-1 Reader/Writer Manual de usuario
SIIG
SIIG UltraATA 133 PCI Manual de usuario
SIIG
SIIG CyberParallel Dual Manual de usuario
SIIG
SIIG NN-000032-S1 Manual de usuario
SIIG
SIIG FireWire 800 + Hi-Speed USB Combo Manual de usuario
SIIG
SIIG ID-P40411-S1 Manual de usuario
SIIG
SIIG SC-SE6412 Manual de usuario
SIIG
SIIG DP PCI-to-PS/2 Manual de usuario
SIIG
SIIG 1 FireWire 800 CardBus DV-Ki Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
