SignaMax 065-7940B-WS Manual de usuario

24-Port Gigabit Web Smart Switch

with 4 SFP (Mini-GBIC) slots

User Manual

V1.4

(April 2008)

065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports

a retrieval system, or transmitted in any form or by any means, whether

electronic, mechanical, photo copying, recording or otherwise, without the

prior written permission of the publisher.

FCC WARNING

This equipment has been tested and found to comply with the limits

for a class A device, pursuant to part 15 of FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a

commercial installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communication.

Operation of this equipment in a residential area is likely to cause harmful

interference, in which case, the user will be required to correct the

interference at the user’s own expense.

This is a Class A product. In a domestic environment, this product may

cause radio interference in which case the user may be required to take

adequate measures.

Take special care to read and understand all the content in the warning

boxes.

065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports

Table of Contents

UNPACKING INFORMATION...................................... 5

INTRODUCTION........................................................ 5

GENERAL DESCRIPTION..........................................................................5

KEY FEATURES ......................................................................................6

THE FRONT PANEL .................................................................................6

THE REAR PANEL...................................................................................7

INSTALLATION ......................................................... 8

DESKTOP INSTALLATION ........................................................................8

RACK INSTALLATION .............................................................................8

INSTALLING NETWORK CABLES..............................................................8

DESCRIPTION OF SWITCH FUNCTIONS .................. 10

JUMBO FRAME ..................................................................................... 10

FLOW CONTROL AND BACKPRESSURE................................................... 10

MIRROR............................................................................................... 10

VLAN................................................................................................. 10

TRUNK (AGGREGATION)....................................................................... 10

QUALITY OF SERVICE (QOS) ................................................................ 10

SNMP ................................................................................................. 10

MANAGEMENT GUIDE ............................................. 11

ACCESS THE SWITCH............................................................................ 11

HOMEPAGE .......................................................................................... 12

SYSTEM ...............................................................................................13

PORT ................................................................................................... 14

VLAN................................................................................................. 15

PVID................................................................................................... 16

065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports

AGGREGATION/TRUNK CONFIGURATION..............................................17

QUALITY OF SERVICE........................................................................... 18

MIRROR............................................................................................... 22

RATE LIMIT ......................................................................................... 23

SNMP ................................................................................................. 24

DISCOVERY.......................................................................................... 25

STATISTICS OVERVIEW......................................................................... 26

DETAILED STATISTICS .......................................................................... 26

RESTART ............................................................................................. 27

FACTORY DEFAULT.............................................................................. 27

SMART BOOT ....................................................................................... 27

SOFTWARE UPLOAD .............................................................................28

PRODUCT SPECIFICATIONS.................................... 29

APPENDIX- COMMAND LINE INTERFACE ................ 30

START-UP AND TERMINAL CONFIGURATION .......................................... 30

COMMAND HIERARCHY........................................................................31

ENTERING COMMANDS......................................................................... 31

COMMAND DESCRIPTION...................................................................... 32

System Commands...........................................................................32

Console Commands.........................................................................33

Port Commands............................................................................... 34

VLAN Commands............................................................................ 36

Aggregation Commands ..................................................................38

QoS Commands............................................................................... 39

Mirror Commands........................................................................... 40

IP Commands.................................................................................. 41

SNMP Commands ........................................................................... 41

Ratelimit Commands .......................................................................42

065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports

Unpacking Information

Congratulations on purchasing this Signamax 065-7940B-WS 24-port Gigabit Web

Smart Switch with 4 SFP module Combo slots. Before you start, please verify that

your package contains the following items:

1. One Signamax 065-7940B-WS 24-port Gigabit Web Smart Switch with 4 SFP slots

2. One power cord

3. Rack-mounting brackets and screws (optional)

4. User Manual CD

Introduction

General Description

This Switch will instantly boost your networking throughput because it provides

you with 24 Gigabit ports that enable true Gigabit connectivity. Users are now

able to transfer large and bandwidth-hungry files faster and hence get a real

efficiency improvement. This efficiency is further enhanced by the user-friendly

Web-based management interface. In addition to the 24 copper ports, the

Switch offers 4 fiber ports (slots) that can be used in the place of the last 4

copper ports (these are interchangeable or ‘combo’ ports). These SFP

module slots offer the option of a long-distance, fiber-based connection. Use of

a SFP module port automatically disables its corresponding copper port.

The management functions enable efficient network usage. VLAN reduces the

collisions caused by broadcasting. Port Aggregation enlarges the bandwidth of

the backbone connection. QoS secures the bandwidth for some

bandwidth-hungry applications like VoIP and video conferencing. The Switch

also supports 802.3x and backpressure flow control mechanisms to ensure the

correctness of data transmission.

065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports

Key Features

24 (twenty-four) 10/100/1000Mbps Gigabit Ethernet ports.

4 (four) SFP slots for optional fiber connection.

Supports auto-detection for SFP module insertion

Auto-discovery function for easy Network management.

8K MAC address entries and 24 groups VLAN table

Supports Port Mirroring.

Supports up to 8 ports and 12 groups port aggregation.

Supports QoS: port-based, tag-based, DSCP priority

Supports full-duplex flow control and half-duplex backpressure

Supports Rate Limit (ICMP Rate, Broadcast Rate, Multicast Rate, and

Ingress/Egress Rate)

Supports Jumbo frame 9K bytes

Supports 500K bytes buffer Memory

Supports Web-based management interface.

Non-blocking wire-speed switching performance

Supports firmware upgrade, SNMP

FCC Class A, CE, VCCI. RoHS-compliant

The Front Panel

The front panel features all the LED indicators and ports:

Device LED:

LED Status Operation

Steady Green The switch is powered on

Power (PWR) Off The switch is powered off

Port LEDs:

LED Status Operation

Green The port is connected at 1000 Mbps

Blinking Green A valid link is established, and there is data being

transmitted/received.

1000M

Off No valid link on this port or the Port is connected at 10/100

Mbps

Steady Green A valid link is established, and there is no data being

transmitted/received.

Blinking Green A valid link is established, and there is data being

transmitted/received.

10/100M

Off No valid link on this port or the port is connected at 1000

Mbps

065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports

Port Operation

The auto-negotiation feature allows ports to run at one of the following operation

modes:

Me ia Spee Duplex Mo e

Full Duplex 10 Mbps

Half Duplex

Full Duplex 100 Mbps

Half Duplex

10/100/1000 Mbps(copper)

1000 Mbps Full Duplex

1000 Mbps(Fiber)

(mini GBIC required)

1000 Mbps Full Duplex

Note: For the interchangeable (combo) ports (the last 4 RJ-45 ports and the fiber

slots), if both the fiber and copper interfaces of an interchangeable pair (combo) are

connected (incorrect set-up), the system automatically accepts the fiber interface and

disables the copper port.

Restore Default Button

You can use this button to reset the switch or restore it to its factory default settings.

To reset the switch, press the button once.

To restore factory default settings, press and hold the button for three seconds.

The Rear Panel

The rear panel:

Power Receptacle

To be compatible with electricity standards around the world, the Switch is designed to

work with voltages between 100 and 240V AC and 50/60Hz. Please make sure that

your region’s electricity supply is within this range.

To power on the Switch, please plug the female end of the power cord firmly into the

receptacle of the Switch and the other (male) end into an electricity outlet (usually a

wall plug). After plugging in the power cord, check if the power LED is lit to indicate

normal power status.

Attention：

：：

：The SFP module (SFP) slots share their LED indicators with their

interchangeable Gigabit RJ-45 (copper) ‘combo’ ports (the last 4 copper ports).

Use of a SFP module slot automatically disables its corresponding copper port.

065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports

Installation

This Signamax 065-7940B-WS Switch can be placed on your desktop or mounted in a

rack. Installation is very easy. Users can use all the features of the Switch by simply

attaching the cables and turning the power on.

Before installing the Switch, we strongly recommend that …

1. … the Switch must be placed in an environment that is well ventilated – a

minimum space around the unit of 25mm is recommended.

2. … the Switch and relevant components are far from sources of electrical noise,

such as radios, transmitters and broadband amplifiers

3. … the Switch’s environment is protected from high levels of humidity.

Desktop Installation

1. Install the Switch on a level surface that can support the weight of the unit and the

relevant components.

2. Plug the Switch’s power cord into the power outlet.

Rack Installation

Rack mounting enables orderly installation in cases where many networking devices

have to be installed in the same area. The Switch is supplied with brackets and screws

for rack-mounting purposes.

1. Disconnect all cables from the Switch before mounting it.

2. Place the unit the right way up on a hard, flat surface with the front facing you.

3. Locate a mounting bracket over the mounting holes on one side of the unit.

4. Insert the screws and tighten them with a suitable screwdriver.

5. Repeat this for the other side of the unit.

6. Slide the unit into the rack and secure it with suitable screws.

7. Reconnect all the cables.

Installing Network Cables

1. Crossover or straight-through cable: All the ports on the Switch support

Auto-MDI/MDI-X functionality. Both straight-through and crossover cables can

be used to connect the Switch with PCs and other devices like switches, hubs or

router.

2. Category 3,4,5 or 5eUTP/STP cable: To make a valid connection and obtain

optimal performance, it is vital to use the appropriate cables that correspond to

the different transmitting/receiving speeds.

3. To choose a suitable cable, please refer to the following table:

065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports

Media Speed Wiring

10 Mbps Category 3,4,5 UTP/STP

100 Mbps Category 5 UTP/STP

10/100/1000 Mbps

copper

1000 Mbps Category 5,5e UTP/STP

1000 Mbps Fiber

(SFP module

required)

1000 Mbps The cable type differs according to the SFP

module you choose. Please refer to the

instructions that came with your SFP module.

065-7940B-WS 24-Port 10/100/1000 WebSmart Switch with 4 SFP Ports

Description of Switch Functions

Jumbo Frame

The Signamax 065-7940B-WS Switch supports Jumbo Frames, which means that it

can transmit the same data in fewer frames. This helps to ensure fewer overheads,

shorter processing time, and fewer interruptions.

NOTE: To enable Jumbo Frame, Flow Control should be enabled in advance.

Flow Control and Backpressure

Flow Control and Backpressure both help devices with different processing speeds to

communicate with each other. This ensures the correctness of data transmissions.

The 802.3x Flow Control and Backpressure mechanisms work respectively for full-

and half-duplex modes. Flow Control can be enabled or disabled on a per-port basis.

Mirror

The Mirror function enables network administrators to monitor all traffic. By forwarding

a copy of the packets that are transferred by the monitored port, the sniffer port

receives all the packets and hence is able to monitor the traffic through the specified

port.

VLAN

This Switch supports Virtual LAN, which means the network can be segmented into

groups to reduce collisions caused by wide broadcasting. The Switch supports both

port-based VLAN and 802.1q tag-based VLAN. Port-based VLAN directs incoming

packets to VLANs according to their ingress ports. 802.1q-based VLAN adds a tag to

the header of the packet to direct the packet to the right VLAN.

Trunk (Aggregation)

The Trunk function groups several ports into one combined transmission channel.

This increases the bandwidth, which helps to boost backbone connectivity. The

Switch allows a maximum of 4 groups and 8 members for each group.

Quality of Service (QoS)

QoS classifies packets into different precedence classes. The packets are transmitted

and received according to their classified priorities. This mechanism helps

high-bandwidth demanding applications such as VoIP to get an unobstructed

connection.

SNMP

The Switch supports SNMP (Simple Network Management Protocol). It allows the

product to be monitored by an SNMP management station.

Tabla de contenidos

Otros manuales de Cambiar de SignaMax

SignaMax

SignaMax C-600 Series Manual de usuario

SignaMax

SignaMax 065-7310F Series Manual de usuario

SignaMax

SignaMax 065-7401 Manual de usuario

SignaMax

SignaMax 098-8040 Manual de usuario

SignaMax

SignaMax SC30010 Manual de instrucciones

SignaMax

SignaMax CommandView FO-098-8080 Manual de usuario

SignaMax

SignaMax 065-7905A Manual de usuario

SignaMax

SignaMax 065-7726SPOE Manual de usuario

SignaMax

SignaMax 065-7508 Manual de usuario

SignaMax

SignaMax SC10010 Manual de usuario

SignaMax

SignaMax 065-7111F Series Manual de usuario

SignaMax

SignaMax 065-7309POEP Manual de usuario

SignaMax

SignaMax C-500 Series Manual de usuario

SignaMax

SignaMax 065-7710 Manual de usuario

SignaMax

SignaMax 065-7890FSFPDP Manual de usuario

SignaMax

SignaMax 065-7908A Manual de usuario

SignaMax

SignaMax C-500 Series Manual de usuario

SignaMax

SignaMax 065-7434 Manual de usuario

SignaMax

SignaMax 065-7707 Manual de usuario

SignaMax

SignaMax 065-7931 Manual de usuario

SignaMax

SignaMax C-100 Series Manual de usuario

SignaMax

SignaMax 65-7542 Manual de usuario

SignaMax

SignaMax 065-7932 Manual de usuario

SignaMax

SignaMax I-120 Series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario