SignaMax FO-065-7330 Manual de usuario
USER’S GUIDE
SignamaxConnectivity Systems
FO-065-7330
FO-065-7340
16 / 24 Ports Ethernet Switch
SignamaxConnectivity Systems
F0-065-7330
F0-065-7340
16 / 24 Ports Ethernet Switch
User’s Guide
SignamaxFO-065-7330 / 7340 Ethernet Switch
User’s Manual
1
FCC Statement
The FCC (Federal Communications Commission) restricts
the amount of radio frequency emission and radiation coming
from computer equipment.
The equipment introduced in this manual has been tested
and found to comply with the limits for a Class A digital
device pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user is required
to correct the interference at his/her own expense.
Any changes or modifications not expressly approved by the
manufacture would void the user’s authority to operate the
equipment.
Trademarks
Product names mentioned in this manual may be trademarks
or registered trademarks of those products.
All trademarks or brand names mentioned are properties of
their respective companies.
SignamaxFO-065-7330 / 7340 Ethernet Switch
User’s Manual
2
Preface
This manual describes how to install and use the SignamaxFO-
065-7330 / 7340, 16 / 24 Ports Ethernet Switch. The TX ports of
the switch introduced here auto-negotiates the presence of
10/100Mbps and full/half-duplex mode and auto-MDIX. In
addition, it allows an optional 100BaseFX multi-mode or single-
mode fiber module, enabling long distance connection.
To get the most out of this manual, you should have an
understanding of networking concepts such as bridging, IEEE
802.3 10BaseT Ethernet, IEEE 802.3u 100BaseTX/FX Fast
Ethernet, and local area networks (LANs).
For more information about these topics, please refer to the
Appendices.
In this manual, you will find:
•Introduction on the SignamaxFO-065-7330 /
7340 Ethernet Switch
•Product features
•Illustrative LEDs functions
•Installation instructions
•Specifications
SignamaxFO-065-7330 / 7340 Ethernet Switch
User’s Manual
3
Table of Contents
FCC STATEMENT1
TRADEMARKS 1
PREFACE 2
TABLE OF CONTENTS 3
PRODUCT OVERVIEW 4
FRONT VIEW 4
PACKAGE CONTENTS 4
PRODUCT FEATURES 5
FRONT PANEL DISPLAY 6
PHYSICAL PORTS 7
INSTALLATION 8
SELECTING A SITE FOR THE EQUIPMENT 8
DECIDING HOW TO INSTALL 9
HOW TO INSTALL MODULE 10
CONNECTING TO POWER 11
CONNECTING TO YOUR NETWORK 11
TECHNICAL SPECIFICATIONS 13
PHYSICAL SPECIFICATIONS 14
CONNECTOR PINOUTS 15
ORDERING INFORMATION 16
CONTACT INFORMATION 17
SignamaxFO-065-7330 / 7340 Ethernet Switch
User’s Manual
4
Product Overview
Front View
Figure 1: The SignamaxFO-065-7330, 16 Ports Ethernet Switch
Figure 2: The SignamaxFO-065-7340, 24 Ports Ethernet Switch
Package Contents
When you unpack the product package, you shall find these items
listed below.
lThe SignamaxFO-065-7330 / 7340 Ethernet Switch
lOne AC power cord
lUser’s Manual
lAccessories: brackets (2 pcs) & bracket screws (6 pcs)
Please inspect the contents, and report any apparent damage or
missing items immediately to your authorized reseller.
SignamaxFO-065-7330 / 7340 Ethernet Switch
User’s Manual
5
Product Features
♦PROVIDES 16 OR 24 × 10/100MBPS PORTS USING RJ-45
CONNECTORS
♦AN OPTIONAL SINGLE-PORT FIBER MODULE ALLOWS:
-100BASEFX MULTI-MODE FIBER WITH SC, ST, MT-RJ, VF-45 OR LC
CONNECTOR
-100BASEFX SINGLE-MODE FIBER WITH SC CONNECTOR
♦AUTO-NEGOTIATION FOR SPEED AND DUPLEX MODE ONTX
PORTS
♦AUTO-MDIX FOR ALL TX PORTS
♦TRUE NON-BLOCKING ARCHITECTURE
♦FULL WIRE SPEED FORWARDING RATE
♦STORE-AND-FORWARD MECHANISM
♦BROADCAST STORM FILTERING CONTROL
♦BACK-PRESSURE AND IEEE 802.3X COMPLIANT FLOW
CONTROL
♦SUPPORTS 8K MAC ADDRESSES
♦4M BITS BUFFER MEMORY FOR THE 16-PORT SWITCH
♦2M BITS BUFFER MEMORY FOR THE 24-PORT SWITCH
♦FRONT PANEL PUSH BUTTON TO CHOOSE 100BASEFX OR
PORT 16 OR 24
♦FRONT PANEL PORT STATUS LEDS
♦STANDARD 19” RACKMOUNT SIZE, ONE-UNIT-HEIGHT
SignamaxFO-065-7330 / 7340 Ethernet Switch
User’s Manual
6
Front Panel Display
An array of LED indicators on the front panel provides you with
instant feedback on each port status, and, helps you monitor and
troubleshoot the switch.
Figure 3: Front Panel LEDs
Œ
Power
This LED comes on when the switch is properly connected to power and
turned on.
•
Push Button
The push button is located at the right side of port 16 on the 16-Port Switch
or of port 24 on the 24-Port Switch.
Depress this button to use port 16 or 24, and press this button to use the
100BaseFX module.
Ž
Port Status
The RJ-45 ports numbered from 1 to 16 on the 16-Port Switch, or 1 to 24 on
the 24-Port Switch.
The LEDs are located at the left side of the switch, displaying status for each
respective port. Please refer to the table below for more information.
Consult the following table for details.
iBefore you use this table for troubleshooting, make sure the switch is
properly connected to power and turned on.
SignamaxFO-065-7330 / 7340 Ethernet Switch
User’s Manual
7
Physical Ports
The 16 / 24 Ports Switch has sixteen or twenty-four 10/100Mbps
ports using RJ-45 connectors and provides one optional slot for
single-port fiber module. The optional module allows fiber type
(multi-mode or single-mode fiber) and connector (SC, ST, MT-RJ,
VF-45, or LC) at user’s discretion.
UNDERSTANDING FRONT PANEL DESIGN
On Power feeding in
Power switched off
Power LED Off Improper connection
On A valid network connection
LNK stands for LINK
Flashing Transmitting or receiving data
ACT stands for ACTIVITY
LNK/ACT
Off No connection
On A valid 100Mbps connection
100 stands for 100Mbps
Port LED
100M
Off A valid 10Mbps connection
SignamaxFO-065-7330 / 7340 Ethernet Switch
User’s Manual
8
Installation
Selecting a Site for the Equipment
As with any electric device, you should place the equipment where
it will not be subjected to extreme temperatures, humidity, or
electromagnetic interference. Specifically, the site you select
should meet the following requirements:
-The ambient temperature should be between 32 and 104
degrees Fahrenheit (0 to 40 degrees Celsius).
-The relative humidity should be less than 90 percent,
non-condensing.
-Surrounding electrical devices should not exceed the
electromagnetic field (RFC) standards for IEC 801-3, Level 2
(3V/M) field strength.
-Make sure that the equipment receives adequate ventilation.
Do not block the ventilation holes on each side of the switch or
the fan exhaust port on the side or rear of the equipment.
-The power outlet should be within 1.8 meters of the switch.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Cambiar de SignaMax
SignaMax
SignaMax 065-7932 Manual de usuario
SignaMax
SignaMax 065-7921PoE Manual de usuario
SignaMax
SignaMax 065-7940B-WS Manual de usuario
SignaMax
SignaMax 065-7726SPOE Manual de usuario
SignaMax
SignaMax 098-8026 Manual de usuario
SignaMax
SignaMax 065-7942 Manual de usuario
SignaMax
SignaMax C-500 Series Manual de usuario
SignaMax
SignaMax 065-7341 Manual de usuario
SignaMax
SignaMax 098-8280 Manual de usuario
SignaMax
SignaMax 065-7006 Manual de usuario
SignaMax
SignaMax 065-7407GPOEP Manual de usuario
SignaMax
SignaMax 065-7861 Manual de usuario
SignaMax
SignaMax 065-7429 Manual de usuario
SignaMax
SignaMax 098-8040 Manual de usuario
SignaMax
SignaMax 065-7345 Manual de usuario
SignaMax
SignaMax CommandView FO-098-8080 Manual de usuario
SignaMax
SignaMax I-120 Series Manual de usuario
SignaMax
SignaMax FO-065-7030Q Manual de usuario
SignaMax
SignaMax 065-7940D-WS Manual de usuario
SignaMax
SignaMax 065-7851 Manual de usuario
