SIGMA TEK CP 101 Manual de usuario

CP 101

S-DIAS CPU Module

Instruction Manual

Date of creation: 10.04.2014

Version date: 26.07.2023

Article number: 20-004-101-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur

through use of this handbook.

S-DIAS CPU MODULE CP 101

26.07.2023 Page 1

S-DIAS CPU Module CP 101

with 1 Ethernet

1 USB Device

1 CAN

The S-DIAS CP 101 CPU module is a high-performance processor unit

for the S-DIAS I/O modules. With the Ethernet and CAN bus interfaces,

the module can be used for various applications. A zero-voltage

protected RAM area is available, which is implemented by copying a

data block from the DDR RAM to the NAND Flash.

The voltage supply is already available in the module. The number of

modules that can be supplied depends on the total current consumption

The CP 101 can supply a maximum of 0.6 A.

S-DIAS has no intelligent master (manager).

CP 101 S-DIAS CPU MODULE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 5 
1.1 Target Group/Purpose of this Operating Manual......................5 
1.2 Important Reference Documentation .........................................5 
1.3 Contents of Delivery.....................................................................5 
2Basic Safety Directives .......................................................... 6 
2.1 Symbols Used...............................................................................6 
2.2 Disclaimer......................................................................................8 
2.3 General Safety Directives ............................................................9 
2.4 Software/Training .......................................................................10 
3Standards and Directives......................................................11 
3.1 Directives.....................................................................................11 
3.1.1 EU Conformity Declaration................................................................11 
4Type Plate...............................................................................12 
5Technical Data .......................................................................13 
5.1 Performance Data.......................................................................13 
5.2 Standard Configuration..............................................................14 
5.3 Electrical Requirements.............................................................14 
5.3.1 Module Supply (Input) .......................................................................14 
5.3.2 S-DIAS Bus Supply (Output) .............................................................15 
5.4 Miscellaneous .............................................................................17 
5.5 Environmental Conditions.........................................................17 

 S-DIAS CPU MODULE CP 101 
 
07.2023 Page 3 
6Mechanical Dimensions........................................................18 
7Connector Layout..................................................................19 
1 Status LEDs.................................................................................20 
2 Connectors..................................................................................20 
3 Applicable Connector Cables....................................................21 
4 Applicable Connectors...............................................................22 
5 Label Field...................................................................................23 
8CAN Bus Setup......................................................................24 
1 CAN Bus Station Number ..........................................................24 
2 Number of CAN Bus Participants..............................................24 
3 CAN Bus Data Transfer Rate.....................................................24 
4 CAN Bus Termination.................................................................25 
9Strain Relief ...........................................................................26 
Process Diagram...................................................................27 
Status and Error Messages..................................................28 
Application Exceptions.........................................................35 
1 Data Breakpoint ..........................................................................35 
Wiring Guidelines..................................................................35 
1 Shielding......................................................................................36 
2 ESD-Protection............................................................................36 

CP 101 S-DIAS CPU MODULE 
 
Page 4 26.07.2023 
Assembly/Installation............................................................37 
1 Check Contents of Delivery.......................................................37 
2 Mounting......................................................................................38 
Transport/Storage..................................................................40 
Storage ...................................................................................40 
Maintenance...........................................................................41 
1 Service.........................................................................................41 
2 Repair...........................................................................................41 
Disposal..................................................................................41 
 

S-DIAS CPU MODULE CP 101

26.07.2023 Page 5

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x CP 101

CP 101 S-DIAS CPU MODULE

Page 6 26.07.2023

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

S-DIAS CPU MODULE CP 101

26.07.2023 Page 7

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require

attention.

CP 101 S-DIAS CPU MODULE

Page 8 26.07.2023

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the

subsequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine

operator is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If

necessary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product

description. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this

operating manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Tabla de contenidos

Otros manuales de Unidad de control de SIGMA TEK

SIGMA TEK

SIGMA TEK EZ 101 Manual de usuario

SIGMA TEK

SIGMA TEK PW 022 Manual de usuario

SIGMA TEK

SIGMA TEK CP 102 Manual de usuario

SIGMA TEK

SIGMA TEK AM 441 Manual de usuario

SIGMA TEK

SIGMA TEK S-DIAS PS 101 Manual de usuario

SIGMA TEK

SIGMA TEK AI 047 Manual de usuario

SIGMA TEK

SIGMA TEK S-DIAS DM 821 Manual de usuario

SIGMA TEK

SIGMA TEK SCP 011 Manual de usuario

SIGMA TEK

SIGMA TEK DIAS-Drive 2000 Manual de usuario

SIGMA TEK

SIGMA TEK SCP 111-S Manual de usuario

SIGMA TEK

SIGMA TEK PIM 021 Manual de usuario

SIGMA TEK

SIGMA TEK KL 181 Manual de usuario

SIGMA TEK

SIGMA TEK VI 021 Manual de usuario

SIGMA TEK

SIGMA TEK SR 022 Manual de usuario

SIGMA TEK

SIGMA TEK DM 167 Manual de usuario

SIGMA TEK

SIGMA TEK C-DIAS Manual de usuario

SIGMA TEK

SIGMA TEK ST 151 Manual de usuario

SIGMA TEK

SIGMA TEK AM 222 Manual de usuario

SIGMA TEK

SIGMA TEK SCP 111-2 Manual de usuario

SIGMA TEK

SIGMA TEK PL 221 Manual de usuario

SIGMA TEK

SIGMA TEK S-DIAS EC 121 Manual de usuario

SIGMA TEK

SIGMA TEK CP 112-1 Manual de usuario

SIGMA TEK

SIGMA TEK AI 022-1 Manual de usuario

SIGMA TEK

SIGMA TEK CSDI 162 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario